Why is there no power when the key is turned?

When that dead/dying battery was in place, the lights would power on dimly while the key was on, and I would hear a clicking sound while trying to start it, but it would not turn over. The battery was tested and needed to be replaced. Now, with a new battery that has been tested to be good, I don’t get any electrical power when turning the key.

Why does my ATV have no power when I turn the key?

When I installed the new battery, I didn’t noticed that there were two positive cables that need to be connected to the positive terminal. One of them had slipped back into the boot, and I only connected the other one. This is why the ATV had no power at all when I was turning the key.

Why does my car not start when I turn the key?

If there is no sound when you turn the key, but the lights and accessories work, it could be the stater relay or starter solenoid. However if there is no sound at all, not even a click, it’s probably your battery.

There are a lot of ways the cars can not start. One of the most annoying ways is when you turn the key and nothing happens. Also, you may have just changed the battery and have no reason to believe it is bad.

Why does the keyswitch not turn the starter?

They keyswitch may not be sending the signal to tell the battery to send juice to the starter, the battery may not be able to send enough power to the solenoid to turn the starter, the solenoid may not be ramping up the power given to it, or the starter may not be functioning and able to turn.

How to diagnose no start, turn key and nothing happens?

Spark (Only gas engines need a spark, diesel engines need high compression and glow plugs in cold weather to start) Compression (without compression the engine will not run, or not have any power) To read my article where I really lay out the FastC method of diagnosing any no start condition read here.

What happens when I turn the key on the starting circuit?

Now, thinking about that starting circuit, consider the things that could be going wrong to interfere with it.

What causes no ignition, or dash lights when turning key?

Q: I have no ignition, or dash lights when turning key. All relays and battery are fine. Dash lights work when headlights are on. I’m thinking its some kind of electrical problem. I got it to start one time with the remote start. After that, nothing. I’ve tried jump box to be sure I have power.

What to do if no power to ignition or headlights?

And its the only thing left on the checklist that is in line to power the solenoid and headlights. Purchased an aftermarket ignition and spliced it in place of the old ignition switch. A starter relay was inexpensive so I purchased one just in case. I put the old starter relay back into the plug.

How to test a no power ignition switch?

A $10 test light from an auto parts store is what you need. Hook it to the negative post on the battery and turn on the key- your small wire to the solenoid should have power- touch the tip of the test light to the terminal and it should light up.

Is it good to turn key and no start / crank?

Automotive Forums .com Car Chat > Chevrolet > Avalanche | C&K | Silverado | Suburban | Tahoe > Silverado > Turn key and no start/crank…bat is good! Turn key and no start/crank…bat is good! Hi guys, Thanks in advance for any help, I have a 01 2500HD Crew cab with the 6.0. Tonight I stopped at the gas station to grab some milk.

Why does my Harley Davidson have no power?

Last Friday I shut the motor off with the stop switch and then turned the ignition key off. I re-set the stop switch to On. 1 minute later, I turned the ignition switch to ignition and noticed I had no power to my headlights and instrument lights.

Why does my boat have no power to guages or ignition?

Unfortunately, we are not able to boat, because my ignition is dead. I have a 2004 Crownline … read more I have a Quicksilver 87-859660A1 Keyless ignition system on my Supra boat and it will not respond to any codes even the emergency code supplied by the manufacturer. This is after setting for 1.5 years … read more

Why does my car not start when I Turn on the lights?

This is the switch you turn in the key or it could be part of it that is connected to that mechanism in the steering wheel. To troubleshoot this, turn on all your lights, try to start the car. If the light dim considerably, your ignition switch is OK.

Is there a problem with the ignition switch?

To troubleshoot this, turn on all your lights, try to start the car. If the light dim considerably, your ignition switch is OK. In my case, when I opened the ignition switch, I saw a bandage around the Ignition Switch that propted me, may be this is the problem but I am not sure yet.

What does it mean when your car won’t turn over but Lights Come On?

No Spark – if your car will crank, but not turn over, but your lights come on, then you might not be getting a spark to the engine even though your electrical components are working. A spark needs to be used to ignite the fuel, letting the car start.

Why is my battery not transmitting any power?

Remember that power needs a ground to complete the circuit, so the issue could also be in the battery ground cable. It could be a corroded or dirty or loose mount or it could be the internal wiring on one of the cables is corroded and damaged so it cannot transmit power even though the outer covering still looks okay.

Why does my car not start when I Turn on the key?

This feature is not available right now. Please try again later. One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

What are the symptoms of a bad ECM power relay?

A bad relay may cause the vehicle to crank, but not start, or sometimes not even crank at all. 3. Battery drain or dead battery. A failed ECM power relay can also cause a battery drain or dead battery. If the relay shorts it can leave power on to the computer, even when the vehicle is turned off.

How is the black wire connected to the starter relay?

The black/red wire is connected to the starter relay via SPL8 (another bundle). Am I correct in assuming that if the relay was bad, it would affect the instruments, lights, and ignition?

Where is the Kill Switch on a Polaris?

The Kill switch is in the run position, the fuses in the fuse box under the front storage box look good. I’m not sure where to go next. I’m not all that mechanically or electrically inclined.

What to do if your starter relay wont click?

Now just because the relay doesnt click doesnt mean its the fault. You could try a voltage check at your relay signal voltage. If you have power coming from your start button it should be measurable.

How can I tell if my car battery is not working?

Check the terminals on the battery for corrosion and tightness. A good way to check how tight they are is to try and wiggle them with your hand if you can wiggle them they are not tight enough. Tighten them and start over. Make sure the battery is installed correctly, and there isn’t a build up of corrosion on the terminals.

Can a BMW dealership program a new battery?

Any BMW dealership will be able to program or register your new BMW battery as well as authorized BMW shops. Special software and plugs are required to perform this process and is best left to the hands of professionals. Luckily, the process is straight forward and a routine job for these shops.

What happens if you skip the BMW computer battery change?

However, the vehicle users must be warned of the danger of skipping the BMW computer battery change that can result in shortening the life of the battery in the vehicle. In addition to that, it can damage the entire components of the electrical system.

What causes a car battery to lose power?

Opening a door or turning the ignition on with the main battery disconnected can cause the battery in the device to lose power as well. Door modules Loss of express-up feature due to loss of stored “pinch point” Engine control module (ECM, PCM, VCM) Loss of learned idle speed which can cause a stalling condition.

What causes a starter to turn off without a key?

At starter the smaller exciter wire is either getting voltage or the solenoid is stuck engaged?? Smaller gauge wire should have no power without key in “start” position but if it can get power from anywhere it will trigger the starter. Look again to see if something is touching or too close there.

Why does the starter turn when hooking up battery?

Verified ignition in the locked position and left keys out of ignition. Again, when I touched the negative battery cable to the negative terminal on the battery, the starter engaged and tried to start the motor. Could the battery be bad?

Why does a light switch have no power when on?

But my results have me stumped and thinking the switch will not work. The case is when the switch is turned On, there is no power going through the switch. Reading with a volt meter.

Why is there no power in my car?

No electrical power even with a new battery that I bought because of the problem. I checked the new battery and it has a strong spark, but not even the lights work…NOTHING WORKS. Is there a main fuse or something because no matter what I do I can’t get anything to work. I even jumped the 2 large connectors on the solenoid and nothing.

Why does my bike start but no power?

Is is it the fuses, you need to find out whats blowing them. bad earth, short etc. Check all connections and especially earth points. Water and moisture in couplings too. Check the battey next..Its NOT the battery that runs the bike or the lights etc, its the generator. The battery is there to start the bike, no other reason.

Is there no power to the dash or ignition?

The problem I’m having with it is I have no power to the dashboard or ignition (turn key and nothing happens…no dash lights and no starter kick).

Where does the power to the ignition go?

Also doesn’t the ignition power run through the ignition Fuse in the 2nd row of the fuse block first or does it run through the ignition switch then down to the fuse block? The ignition switch is at the base of the steering column, on top, and has a huge plug with a number of 10 AWG wires going to it.

Where does the power go before it goes bad?

And what kind of trouble do they cause before they go bad? Also doesn’t the ignition power run through the ignition Fuse in the 2nd row of the fuse block first or does it run through the ignition switch then down to the fuse block?

What to do when your car has no power?

id try flicking kill switch back n forth a couple times it could be corroded and dirty then try wiggleing plugs at kill switch ignition switch and fuze possible dirty connection and make sure connections at battery and ground on frame are tight

Why is my electric bike not charging properly?

1. CYCLE ANALYST SETTINGS MAY HAVE BEEN CHANGED CAUSING UN-INTENDED RESULTS. 2. MOTOR HALL SENSOR MAY HAVE BEEN DAMAGED. -CONTACT VESSEL BIKES FOR MORE INFORMATION ON TESTING FOR THIS CONDITION. 3. E-BRAKE MAY BE CAUSING THIS ISSUE IF ACCIDENTALLY BEING PRESSED. Q. Does pedaling re-charge the battery? A. Not really.

Why is there no power from the battery?

Logic so far: – If we supply power by a route other than directly from the battery, the car behaves differently, therefore power from the battery is not reaching the car. The most likely cause of that is some kind of contact problem between the battery and the car. Battery terminals often corrode.

Why does my car not have any power?

– If we supply power by a route other than directly from the battery, the car behaves differently, therefore power from the battery is not reaching the car. The most likely cause of that is some kind of contact problem between the battery and the car. Battery terminals often corrode.

What should I do if my battery is not working?

Press on Windows key+I to open Settings and click on Update & Security. Check for updates here and download and install them. Don’t forget to reboot your laptop before checking if the battery is working again or not. 2. Power Adapter

Is there no power to the car BA?

New car battery, but there is no power to the car jeep ba… The Jeep has been sitting for 2 months and went to start it and it did not even make any noise, I pulled the battery and had it charged, put it in the car and still got absolutely nothing. No lights go on, and none of the dash controls work.

Why does my car make no sound when I start it?

Most likely a dead battery. Start by getting a jump start. Do the lights on the dashboard turn on? If there is no sound when you turn the key, but the lights and accessories work, it could be the stater relay or starter solenoid. However if there is no sound at all, not even a click, it’s probably your battery.

What does it mean when your car won’t start when you turn the key?

The same is true if your headlights come on, but the car won’t start. If your instrument panel lights don’t come on when you turn the key, then your battery is totally dead. You get a jump and it works – If you get a jump, you need to let the car run for a few minutes.

What happens when you turn the key on a car?

The higher rate of electricity gives the starter motor more “oomph” to turn the engine over. The process of starting the car begins at the ignition switch in the driver’s cockpit. The key turn completes a small circuit that tells the battery to release power to the starter solenoid.

How does a key turn work on a starter motor?

The key turn completes a small circuit that tells the battery to release power to the starter solenoid. The solenoid ramps up the power given to it and that power causes the starter motor to turn very quickly.

What should I do if my battery charger is not working?

Almost certainly it’s a battery problem, either low charge or bad cable connection. Charge the battery on a good bench charger, not a Tender, but a real charger. Remove and reconnect both battery cables making sure they are tight and connections are clean. This sounds like a discharged battery to me just saying.

Why is my car not turning on when I Turn on the ignition?

Of course, if you access the car itself with your key, you likely won’t be able to turn on the ignition because of all those extra tumblers. And on the off chance that you do turn the ignition cylinder, the immobilizer won’t allow you to start the car, because it’s protected by one-in-millions of transponder codes.

What to do if your ignition switch is bad?

Bad Ignition Switch: If your battery checks out, but the starter is still silent, it might be a faulty ignition switch. Turn the key to the “On” position, not all the way to start, and check the following: If the red warning lights on your dash don’t light up and your battery connections are clean, the ignition switch is bad.

Why does my car not start when I put the key in?

Putting the key in the ignition switch and starting the car feels like second nature. However, if your car has ignition switch problems, you may not be able to start the car at all. Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems.

Why does my bike stop when I Turn on the ignition?

The main fuse is not part of this circuit and the only thing that stops the ignition working is the kill switch and the ignition switch which both connect a wire from the CDI unit to ground (negative – the frame). When you turn the ignition ‘on’ all you are doing is opening this connection so the CDI is no longer grounded.

Navigation