Why is my third brake light cracked on my CLK?
Even if you have not already experienced a cracked third brake light (officially termed ‘center high-mounted stop lamp’) on your W209 CLK, the chances are that sooner or later you will. The design of the unit seems unable to tolerate the successive shocks that its mounting on the trunk lid is bound to inflict. Tip: don’t slam the lid.
Do you need brake light switch for Mercedes?
Very familiar with models such as E 320, C 240, SLK, CLK and several other Mercedes-Benz chassis. Luckily for you this is a very easy repair that you can also perform yourself. All you need is a Brake Light Switch for your Mercedes-Benz model.
Why does my left brake light keep coming on?
Mercedes 2013 C-250 – false dashboard warning light keeps coming on for left rear brake and tail light every day but my lights are ok! Bought the ML350 used and have changed 3 bulbs since February but the same “left brake light” message keeps coming up!
Why does my Bas light come on in my Mercedes Benz?
To reset the lights, start up your Mercedes-Benz and turn the steering wheel all the way to the right, then all the way to the left. Do this a couple of times. Turn off the engine. Restart. Brake Light Switch may cause BAS / ESP / ABS light to come on. It is the most common problem with Mercedes-Benz cars.
What are the brake lights on a Mercedes Benz?
Mercedes-Benz’s E-Class is no exception. So when it comes to the brake system, the brake lights in your Mercedes-Benz E-Class w211 are important things to consider. However, when drivers think about their vehicle’s brake lights, they usually think about the left and right tail lamps.
How do you replace the third brake light?
The panel that secures the light fixture for the third brake light is secured with T25 Torx screws. Remove the six T25 Torx screws. Then, pull down the carpeting to expose the third brake lamp. Figure 3. Location of T25 Torx screws.
What should I do if my brake lights are not working?
One pair of contacts (1 & 2) are normally-closed and go to the ESP control unit (N47/5). The other pair (3 & 4) are normally-open and go to the SAM for all the stop lights. TANKS FOR YOUR POST, IT WAS VERY USEFUL .CAN YOU SAY HOW SHOULD ADJUSTED STOP PEDAL SWITCH AND HOW IMPORTANT IT IS (ADJUSTMENT)?
Where is the brake light on a Mercedes Benz?
The brake light assembly can then be removed from the outside of the trunk lid. It is easier to disconnect the cable when the brake light is partially removed from the trunk lid.
Even if you have not already experienced a cracked third brake light (officially termed ‘center high-mounted stop lamp’) on your W209 CLK, the chances are that sooner or later you will. The design of the unit seems unable to tolerate the successive shocks that its mounting on the trunk lid is bound to inflict. Tip: don’t slam the lid.
The panel that secures the light fixture for the third brake light is secured with T25 Torx screws. Remove the six T25 Torx screws. Then, pull down the carpeting to expose the third brake lamp. Figure 3. Location of T25 Torx screws.
How do you install a new brake lamp?
Install the new brake lamp through the space in the trunk lid, and re-fit the connector ensuring that it is locked in position. Attach the bracket using the two screws, being careful here not to over-tighten. Finally ensure that the lamp is seated flush with no gaps at the surface, as it must form a waterproof seal.
Can a defective brake light switch still work?
(Brake light switch can still be defective even if the brake lights work. Checking the brake light operation is not a good test.) ESP, BAS, ABS lights turn on. Car won’t shift properly. Stuck in gear. To change the brake light switch on your Mercedes-Benz you will need a star torx bit set. You can buy a set on Amazon for under $20.
Why is my brake light not working on my Mercedes?
Yes it could be the brake light switch. It could be other problems such as low brake fluid level or failed ABS wheel speed sensor. There is no certain way to know without first doing some troubleshooting. Where is the brake light swtich located on a Mercedes-Benz? Right above the brake pedal.
How do you change the brake light switch on a Mercedes?
Once you remove the old brake light switch, unplug the electrical wires from it. Plug the wires in the new switch and install the new switch by twisting it counter-clockwise. Watch the following video on how to install brake stop light switch on an Mercedes-Benz E-Class . I replaced the brake light switch but the lights are still on.