Why does my kvf360 reset belt light keep coming on?
Do not turn the ignition on with the CVT cover removed or the KEBC motor will spool out and prevent you from putting the cover back on (unplug the KEBC motor if you do). Note: A poorly connected battery can cause the light to repeatedly come on even if the switch doesn’t flip.
When to reset belt light on Kawasaki ATV?
However, the belt light may stay on after flipping the switch back to “ON”, or it may have come on automatically at 100 hours to get you to return the machine to the dealer for inspection even though the belt switch is not tripped. The following procedures will reset the light if the belt switch is not tripped.
What to do when your belt light keeps coming on?
Belt light came on and bike went to limp mode. Checked the toggle switch in the cover and did the belt light reset procedure. Belt toggle switch was not tripped as it was still in on position. Still reset the light and switched the toggle switch back and forth a few times just to be on the safe side.
Is there a belt Trip Switch on a Kawasaki 360?
This has been the case with many 360 owners, they found them after looking further. There is a procedure in the Vforce folder for the Vforce to reset the light. The Vforce does not have a belt trip switch. Note: Disconnecting the battery does not reset the light.
Why is the belt light flashing on my KVF 360?
The 4×4 and the Belt light are flashing. The Belt is brandnew and was changed from a Kawasaki dealer. Another problem is, that the KVF is driving normal and maybe a 10 minutes later the ATV has no power and makes misfire. After i turn the ignition off and wait a few minutes everything is normal for another 10-30 minutes.
However, the belt light may stay on after flipping the switch back to “ON”, or it may have come on automatically at 100 hours to get you to return the machine to the dealer for inspection even though the belt switch is not tripped. The following procedures will reset the light if the belt switch is not tripped.
When is the LED light is flashing the ATV?
When the led light is flashing the atv won’t I have an 2006 Kawasaki Prarie 360 and the 4×4 lights keep..atv..bike… their is a failure in the actuator controller system and that is why the 4X4 light is flashing. how many seconds apart are the flashes? I looked it up in the manual and it seems like its only the engine brake.
This has been the case with many 360 owners, they found them after looking further. There is a procedure in the Vforce folder for the Vforce to reset the light. The Vforce does not have a belt trip switch. Note: Disconnecting the battery does not reset the light.
Where is the belt light reset button on a Kawasaki P650?
Belt light reset procedure for late 2003 and later P650, P360, and BF650SRA. 1. Turn the ignition switch OFF. 2. Disconnect both sets of 5 pin connectors located above the CVT cover. Note: These connectors are located just beneath the shift handle on the right side of the 650; one is black and one is grey.
How do you reset the belt light on a prairie 360?
Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them. Cut the key on to verify the procedure worked.
Do not turn the ignition on with the CVT cover removed or the KEBC motor will spool out and prevent you from putting the cover back on (unplug the KEBC motor if you do). Note: A poorly connected battery can cause the light to repeatedly come on even if the switch doesn’t flip.
Belt light came on and bike went to limp mode. Checked the toggle switch in the cover and did the belt light reset procedure. Belt toggle switch was not tripped as it was still in on position. Still reset the light and switched the toggle switch back and forth a few times just to be on the safe side.
Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them. Cut the key on to verify the procedure worked.
Where can I buy a 2003 Kawasaki Prairie 360?
2003 Kawasaki PRAIRIE 360 4X4 (KVF360-A1) Original Equipment Manufacturer Parts at Babbitts Kawasaki Partshouse
Where is the belt failure switch on a Kawasaki ATV?
1. Turn the ignition switch OFF. 2. Disconnect the belt failure switch at the 2-pin connector above the CVT cover. (Note: Just follow the wires coming from the rectangular black box on the CVT Cover to locate this connector.) 3. Disconnect both sets of 5 pin connectors located above the CVT cover.
Is the Kawasaki 360 belt light the same as the 2003 650?
The 360 belt light behavior is very similar to the 2003 650. If at first you can not find the right connectors, keep looking deeper because they really are there in a similar location to the P650. This has been the case with many 360 owners, they found them after looking further.
Is there a Kawasaki kvf360 Prairie ATV service manual?
The Kawasaki KVF360 Prairie ATV online manual will help you repair the following Kawasaki 2×4 and 4×4 ATVs: Subscribe to the Kawasaki KVF360 Online Motorcycle Manual Now- CLICK HERE!
2003 Kawasaki PRAIRIE 360 4X4 (KVF360-A1) Original Equipment Manufacturer Parts at Babbitts Kawasaki Partshouse
How do you replace a belt on an ATV?
This video shows how to remove and replace the Belt on a Brute Force or Prairie, Covers all models. Belt replacement is quick and easy once you have the primary clutch removal too. This method is by far the most straight forward and will not damage the new belt on installation. by Everything ATV UTV Reviews.