Why does my international 4300 engine not start?
Replaced injector, put new orings on hipop. It will not start. Runs on ether but dies as soon as ether stops. Replaced both batteries. Checked fuses by batteries. All good. We pulled the ipr and bench tested it. It was working. Scanner says 8 engine codes. They are: FMI=4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE.
What should the fuel pressure be on an international 4300?
Need 20 psi to start, 65 psi when running. Hold your schrader valve open during crank to make sure there is solid fuel flow there. If you have the test fitting on the fuel filter cap, you can check for pressure there too. Even the hand primer pump should be able to build up to 60 psi and get hard. spsauerland Thanks this.
Is the IH 4300 DT466 getting hard to start?
I have an 05 IH 4300 DT466 with 131K miles on it. I have had a small problem with it before, usually first thing in the AM. But now it doesn’t want to start no matter what time of the day it is. If its been sitting for any length of time it cranks and will finally start after about 45 seconds.
What to do if your International Truck won’t start?
International 4700 Truck Won’t Start, Ignition Switch or Gear Selector ? (Solved) – YouTube International 4700 Truck Won’t Start, Ignition Switch or Gear Selector ? (Solved) If playback doesn’t begin shortly, try restarting your device.
Can a 2007 IH 4300 run in sub zero temps?
The place I work at has a 2007 IH 4300 with a DT466. The past few days have been sub zero temps here. It ran fine the beginning of the week but yesterday it wouldn’t start. We pushed it in the garage and let in warm up over night. We also put the batteries on charge since they were pretty weak.
Where is the starter on a 2004 DT466?
If you start from behind the head and start feeling downwards and onto the bell housing you will see that it is mounted with one small bolt at about the 11 o’clock position . It is above the starter by about 12 inches for sure but right on top of the bell housing .
Where are the lights on my international 4300?
The highbeam headlights, markers and all other lights function properly. I have checked the fusebox in the engine compartment and above the glovebox and am unable to locate either a DRL/headlight, fuse or relay. We would love to have a troubleshooting guide, or schematic, but have been unable to locate one on the internet.
What kind of truck is the International 4300?
Our 2009 International 4300 MaxForce DT (7.6L) truck is shifting into neutral as we are driving down the highway. We have to pull off and turnoff engine 5 minutes and then restart and drive for anothe … read more
What’s the ABS light on an international 4300?
2012 INTERNATIONAL 4300 DT466 MAXFORCE… *****************. I HAVE AN ABS LIGHT AND WARNING BEEPER CONSTANT, I HAD A … read more Our 2009 International 4300 MaxForce DT (7.6L) truck is shifting into neutral as we are driving down the highway. We have to pull off and turnoff engine 5 minutes and then restart and drive for anothe … read more
What’s the electric fault on an international 4300?
I have an international 4300 and the electric fault and abs… Vocational, Technical or Tra… I have a 2012 international with datalink issues Data link issues. Looking for help troubleshooting cause
Is the battery box on an IHC truck bad?
More than 1/2 of the road services I do for Budget Rental on IHC trucks are bad connector in battery box. More than 1/2 is being generous! Heavyd Thanks this. Overall a great company to work for. They genuinely care about the drivers and are constantly looking for ways to improve.
Why is my MaxxForce crank but no start?
I also heard that using cheap fuel filters causes issues. They are all expensive and hard to find American made filters. Foreign made junk should cost end users less but it usually cost you more in other areas. Like a cheap air filter that a contractor installed. It somehow got rain water intrusion and sucked part of the filter into the engine.
What’s the oil pressure on a 2006 International 4300?
SPN175 ENGINE OIL TEMP. SPN 102 BOOST PRESSURE. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 100 ENGINE OIL PRESSURE. FMI= 3 VOLTAGE ABOVE NORMAL OR SHORTED TO HIGH SOURCE. SPN105 INTAKE MANIFOLD TEMP. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 94 FUEL DELIVERY PRESSURE.
Is the IDM a bad design on the 2005 model?
My personal opinion is that the IDM is a bad design on the 2005 model. It was the first year for the new body and engine. So the IDM needs 39 amps and the fuse and circuit are only 40. now that they are old the resistance has gone up in the IDM, injectors, and injector harness so the IDM pulled extra power and overheats the circuit.
What makes a 2003 International 4300 sputter and Miss?
I have a 2003 International 4300 with a DT466. I just had all the O-rings on the injectors replaced along with the wiring harness that goes to the injectors. Now once the truck gets up to running temp it starts to sputter/miss. Truck runs GREAT cold but once warm gets worse.
Why does my DT466 diesel truck start smoking?
The truck will crank and accelerate great, then it begins smoking and goes into a limp mode with little pedal reaction. If you raise the rpm’s the smoke goes from whitish grey to dark almost black, but only when you raise the rpm’s.
How to program IDM for DT466 international?
Hi, any ideas for how to program IDM on DT466 international, deal won’t do it unless buy part from them which selling me at $1500, and I got from Ebay at $300 already, I have software MD32 DLC ( Diamond Logic Controller) which has program on menu, does it works? Thanks
Why does my 1999 IH dt466e keep dying?
I have a 1999 IH DT466E that will not stay running. It will start right up and then run from anywhere from 30 secs. to several minutes. It then dies, but will start back up and do the same thing. I have replaced the fuel filter on the drivers side, and the high pressure oil pump is also new last fall.
What should fuel pressure be in 2005 DT466?
You will see the pressure relief ball. It may be partially unseated by debris causing a drop in fuel pressure. Anyway, you will notice a compuchek fitting on the top of the filter housing cap. You plug in a fuel pressure gauge here to test your fuel pressure. Need 20 psi to start, 65 psi is normal running pressure.
What kind of engine does an International 4700 have?
Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by rshackleford, Feb 4, 2011 . Have a 1998 international 4700 lo profile service truck with a t444e engine. while truck was running died acted like it just run out of fuel no sputtering. Has fuel and cranks over fine. good voltage to engine.
Is there an international fault code for FMI 8?
International 4700: 1998 international 4700. Erratic idle, 1998 international 4700. Erratic idle, then dies. Codes are. Sid 21 FMI 8 and FMI 2 Sid 247 FMI 2 Pid 110 FMI 14 Pid 111 FMI 2 Sid 254 FMI 8 Is this a crank position sensor problem? … read more
What are the trouble codes for International trucks?
International Trucks Diagnostics Trouble Codes (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar
Where do I find the Diagnostic Code on my truck?
The ability to display diagnostic trouble codes (DTC) is an optional feature. Codes may be displayed on either the gauge cluster or an optional vehicle information display (VID). The vehicle must be equipped with the option to display codes in both cases.
Can a 2007 International 4400 cab start fine?
No announcement yet. I have a 2007 International 4400 commercial cab KME. I love the engine. However, it has a starting issue. Sometimes it will start fine, but and jump the two large terminals on the starter solenoid on the starter. you don’t need to hold the screwdriver across the contacts till it starts. Once it starts it is fine.