Why does my bike not Rev past 5K rpm?
Just been out again and the exact same thing is happening, runs fine and when it gets to 5k rpm in an gear it splutters and theres like no more engine noise just like a bang bang bang, pop pop pop kinda thing. Hard to explain really although i tried to power out of it as if it might be a blockage but it was having non of it.
Is there a bike that wont Rev past 4K?
Still perfect at low revs and starts fine, as always. Only noticeable once you start to creep upto 4k+ Just checked the fuel line Jamie, its fine. Theres only one tube, from tank to LH carb with the fuel filter in the middle. Thanks both. This post is not being displayed . Nearly there…
Why does my bike cut at 4K rpm?
No reason why its not electrical. For instance, Viragos are notorious for cutting at a about 4-5k due to the vibration affecting the side stand switch connection. I would certainly check all the CDI connectors and the coils.
Is there a way to deactivate low rpm mode?
4) I lost my remote, so I did’t have a way to deactivate the Low RPM mode (L-Mode) if that had been the problem. The L-Mode light was not on, but perhaps the bulb could have burnt out? Doing more research, I found that L-Mode limits your engine to about 5,000 rpm.
When do you start the car, the engine revs?
Car engine revs way up immediately upon starting engine. Q: Car engine revs way up immediately upon starting engine. When starting the engine, it sounds like you have your foot pressed to the floor on the gas pedal as soon as you start it, without even having your foot on the gas.
When does the engine lose power when driving?
Engine revs and loses power when driving. I have had this car in for a fix at two different dealers. When driving at highway speeds the tachometer revs to 5 or 6,000 RPMs car loses power. The first fix was a problem with the cruise control cable.
What do I do when my generator gives me a RMP sense loss error?
What do I do when my generator gives me a RMP sense loss error? If the unit was running and shuts down, attempting to restart, clear the alarm by pressing the ENTER button twice, then press AUTO. Next, remove some of the loads. Try putting it back in AUTO and then restart.
Just been out again and the exact same thing is happening, runs fine and when it gets to 5k rpm in an gear it splutters and theres like no more engine noise just like a bang bang bang, pop pop pop kinda thing. Hard to explain really although i tried to power out of it as if it might be a blockage but it was having non of it.
Why do I have a problem shifting gears on my bike?
It can also be caused by a bent derailleur hanger. Solution: If the chain won’t run to the bottom of the cassette and shifts over the big cog into the spokes (or vice-versa), it sounds like a bent rear hanger needs straightening or replacing. If you’ve been in a crash or damaged the bike somehow, this is the likely cause.
How fast will I be going at 90 rpm in all combinations?
How fast will I be going at 90 rpm in all combinations of these gears? Colors group similar values. 20+ is green, 10ish-20, blue, and below 10, red.
No reason why its not electrical. For instance, Viragos are notorious for cutting at a about 4-5k due to the vibration affecting the side stand switch connection. I would certainly check all the CDI connectors and the coils.
Still perfect at low revs and starts fine, as always. Only noticeable once you start to creep upto 4k+ Just checked the fuel line Jamie, its fine. Theres only one tube, from tank to LH carb with the fuel filter in the middle. Thanks both. This post is not being displayed . Nearly there…
Why does my bike run fine before gasket change?
Ran great before the gasket change, only a few weeks ago i use POR-15 on the fuel tank and its immaculate inside, all new fuel tubing and carbs were cleaned. I went out this morning and it felt fine as usual. Thanks alot for your help mate. This post is not being displayed . Nearly there…