Why did my timing belt break off my 2004 Jetta?
I just want to know the timing marks for a 2004 jetta 2.0 because my timing belt broke off ‘the camshaft it has the but I just want to know the timing marks for a 2004 jetta 2.0 because my timing belt broke off ‘the camshaft it has the but – Answered by a verified VW Mechanic
How to fix timing marks on a Jetta?
Tighten securing nut to 20 Nm (15 ft. lbs.) Continue turning crankshaft two turns in the direction of engine rotation until the engine is again at TDC cyl. 1. When doing this it is important that the last 45°(1/8 turn) turnis performed without stopping.
What are timing marks on VW 2.0 engine?
FIG : View of camshaft damper aligned with the timing mark-Volkswagen 2.0L (AEG) 4-Cyl. engine- FIG : Adjusting the timing belt tensioner-Volkswagen 2.0L (AEG) 4-Cyl. engine- Make sure that the camshaft and crankshaft timing marks are aligned.
How do you set the timing belt on a VW?
Install the lower and center timing belt covers. Install the vibration damper and torque the damper-to-crankshaft sprocket bolts to 18 ft. lbs. (25 Nm). Using the 2-Hole Tensioning tool T-10020, rotate the timing belt tensioner counterclockwise until notch 1 and indicator 2 align. Then, tighten the timing belt tensioner nut to 15 ft. lbs. (20 Nm).
Where are the timing marks on a 16 valve engine?
Slide the timing belt from the sprockets. Check the alignment of the timing marks. On 16-valve engines, the mark on the tooth should align with the mark on the rear belt cover. Install the new timing belt and tension the belt so it can be twisted 90° at the middle of it’s longest section, between the camshaft and intermediate sprockets.
https://www.youtube.com/watch?v=8H2-DRZxPSQ
What kind of belt does a VW Jetta use?
This VW Jetta timing belt system consists of a wear resistant, high strength, corded/molded rubber timing belt (a.k.a. VW Jetta toothed belt). There’s also an assortment of tensioner and idler rollers to guide and tension the VW Jetta timing belt. It’s very important to service your 2.0T VW Jetta timing belt.
How long does it take to repair a VW Jetta?
Answered in 35 minutes by: 12/12/2010 VW Mechanic: marcpod, Own collision repair advice replied 10 years ago marcpod, Own collision repair advice Category: VW Satisfied Customers:2,882 Experience: i-car/Basf training, 300 repairs and 650,000 in Collision monthly 18 yrs exp/licensed adjuster Verified marcpod :
How to set the camshaft pulley on a Jetta?
Set camshaft pulley to TDC No. 1 cylinder by turning the crankshaft. Mark on camshaft pulley must align with (arrow) on toothed belt guard. Loosen tensioning roller and remove toothed belt from camshaft pulley. Turn crankshaftback slightly.
Where is the crankshaft located on a Jetta?
Crankshaft is at TDC, cylinder 1. Before tensioning the toothed belt, turn the tensioning roller eccentric pulley using the pin wrench -T10020-five times all the way in both directions. Procedure Tension camshaft drive belt.
What should the crankshaft temperature be on a Jetta?
The Engine must be no more than warm to the touch. Crankshaft is at TDC, cylinder 1. Before tensioning the toothed belt, turn the tensioning roller eccentric pulley using the pin wrench -T10020-five times all the way in both directions.