Why are all the lights on my Jeep Liberty not working?
I have a 2004 Jeep Liberty, and my drivers side taillight,tag light and front marker lights all stopped working,the turn signal and brake lights still work,anyone know what the problem is :sick: It would have to be either a fuse (fuses?), a broken connection or bad plug.
Are there any turn signals on a Jeep Wrangler?
No turn signals, hazards or brake lights…so I figured I blew the multifunction switch. Today I replaced the multifunction switch, removed all LED bulbs and replaced with the standard bulbs and reinstalled the OEM flasher relay into the new multifunction switch. Still no turn signals, hazards or brake lights.
Are there brake lights on a Jeep Wrangler?
Today I replaced the multifunction switch, removed all LED bulbs and replaced with the standard bulbs and reinstalled the OEM flasher relay into the new multifunction switch. Still no turn signals, hazards or brake lights. The standard bulbs and OEM relay all worked just fine before switching to the LED bulbs.
What does the green light mean on a Jeep Wrangler?
The green with red tracer is your brake/turn signal (check with test light to see if it flashes), and the purple with black (i believe) is your reverse. See what you get at those wires. If there is power there and the signal is flashing, it is likely a ground issue.
What happens when you turn off the headlights?
When the headlights are on, the brake lights, running lights, back-up lights all function as expected. The Hazards and the turn signals do not work. If the turn signals or hazards are on and then the headlights are turned on, the lights stop blinking. They will resume blinking when the headlights are turned off.
Why are the turn signals on my Jeep not working?
Jeep Turn Signals not Working? Here is a quick fix. – YouTube Jeep Turn Signals not Working? Here is a quick fix. If playback doesn’t begin shortly, try restarting your device.
Are there turn signals that blink when the headlights are on?
This time, the turn signals will not blink when the headlights are on. Since they say that it takes a a village to raise a child (or an idiot, in my case), this Village Idiot is turning to the MJR village for help. I recently changed the standard tail lights out for LEDs. I have had LEDs for turn signals in the front for years.
When the headlights are on, the brake lights, running lights, back-up lights all function as expected. The Hazards and the turn signals do not work. If the turn signals or hazards are on and then the headlights are turned on, the lights stop blinking. They will resume blinking when the headlights are turned off.
Jeep Turn Signals not Working? Here is a quick fix. – YouTube Jeep Turn Signals not Working? Here is a quick fix. If playback doesn’t begin shortly, try restarting your device.
Why are the parking lights on my Jeep Patriot not working?
The exterior lighting for your Jeep is pretty simple and yes something is wrong as your front parking bulbs should be on. The question then becomes – what the heck would cause that? I doubt both bulbs would “halfway” burn out at the same time?
This time, the turn signals will not blink when the headlights are on. Since they say that it takes a a village to raise a child (or an idiot, in my case), this Village Idiot is turning to the MJR village for help. I recently changed the standard tail lights out for LEDs. I have had LEDs for turn signals in the front for years.
Are there blinkers on a 2002 Jeep Wrangler?
I have a 2002 TJ Sport, all stock and no PO modifications. Yesterday I swapped out the front marker, side marker, tail and reverse light bulbs with LED’s from superbrightleds.com (using the stock housings) and installed their LED turn signal relay.
I have a 2002 TJ Sport, all stock and no PO modifications. Yesterday I swapped out the front marker, side marker, tail and reverse light bulbs with LED’s from superbrightleds.com (using the stock housings) and installed their LED turn signal relay.
The green with red tracer is your brake/turn signal (check with test light to see if it flashes), and the purple with black (i believe) is your reverse. See what you get at those wires. If there is power there and the signal is flashing, it is likely a ground issue.
Today I replaced the multifunction switch, removed all LED bulbs and replaced with the standard bulbs and reinstalled the OEM flasher relay into the new multifunction switch. Still no turn signals, hazards or brake lights. The standard bulbs and OEM relay all worked just fine before switching to the LED bulbs.
What are the symptoms of a bad Flasher relay?
Another symptom of a faulty flasher relay is hazards or turn signal lights that stay on. If the flasher has any sort of internal short it may cause the hazards or signals to stay on when they are activated, instead of flashing.
Is there a problem with my Jeep Liberty blower control?
Been problem free through 73,000 miles except for the blower control. This is a 4 position switch that only the fourth position works on. Does anyone know if this sounds like a switch, or is it something more complicated? If it is a switch, I can probably change it, if not probably a trip to the dreaded dealer. Thanks
What’s the problem with my 2004 Jeep Liberty?
We just had our 2004 Jeep Liberty in to get the power steering pump and P/S hih pressue line replaced; when we got it back from dealer, the horn wasn’t working?
Why does my Jeep not start when there is no power?
There is a wire that goes to the power distribution box on the finder close to the battery, if you don’t have power to it nothing will work. Could be a dirty connection there or there is also a large main fuse in the PDB that supplies power to all circuits in the jeep. I would check the fuse box for problems.
Is the Liberty CRD required to have DTR lights?
My ’05 Liberty CRD does not have DTR lights. As a matter of fact, they were not required by federal regulation as of that date. Many vehicles being sold to Canada and other countries are required to have DTR lights. A/C blower 2nd speed stopped working then 3rd stopped.
What was the damage to my 2002 Jeep Liberty Limited?
Our 2002 Jeep Liberty Limited was in a small fender bender and was repaired. They replaced the front bumper and some of the front lights, can’t remember which ones. Anyways, the passenger side low beam does not work while the driver side low beam does.
I have a 2004 Jeep Liberty, and my drivers side taillight,tag light and front marker lights all stopped working,the turn signal and brake lights still work,anyone know what the problem is :sick: It would have to be either a fuse (fuses?), a broken connection or bad plug.
My ’05 Liberty CRD does not have DTR lights. As a matter of fact, they were not required by federal regulation as of that date. Many vehicles being sold to Canada and other countries are required to have DTR lights. A/C blower 2nd speed stopped working then 3rd stopped.
Our 2002 Jeep Liberty Limited was in a small fender bender and was repaired. They replaced the front bumper and some of the front lights, can’t remember which ones. Anyways, the passenger side low beam does not work while the driver side low beam does.
What was the misfire code on my 2002 Jeep Liberty?
Just finished putting in a used engine in my 2002 3.7 liberty. Fired off great and once warmed up started miss firing. Code showed miss fire on #4 and #6 cylinders I did the typical swap coil packs. Pulled the fuel rail and checked all of the fuel injectors.
Why are there no tail lights on my Jeep Grand Cherokee?
My 2004 grand cherokee is acting all sorts of crazy im really convinced that its always had some sort of electrical issue somewhere that hasnt been found yet. The current issue im battling is a brake light. tail lights work but not brake one side or the other intermittently.
Where are the lights on a Jeep Wrangler?
For more serious off-roading you can step up the light of your ride with high-powered light bars. There are bars that can be installed to the front bumper or rear bumper of your Jeep Wrangler. They feature an array of high-powered LEDs and deliver impressive levels of illumination so you can drive with confidence.
Why are the brake lights not working but the tail lights are?
Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.
What to do if your Jeep Liberty is having trouble stopping?
If your Liberty is having trouble stopping, or noticeably leaking fluid, don’t drive it. Just have it towed to a mechanic. If you mess up fixing your engine, the vehicle does not move. If you mess up fixing the brakes, it doesn’t stop.
Why does my third brake light fall out?
Third brake light rust, due to poor seal and design. Cost hundreds of dollars in repairs, which is silent until the light falls out and damage is beyond a simple repair. I was alerted to this by the auto body shop, that told me it was common in Jeep Liberty, and did my research.
What are the warning lights on a jeep?
The following are warning lights and indicators found in vehicles built by Jeep. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are nearly 80 of them so be patient!
Where is the fan switch on a Jeep Liberty?
Nothing is wrong with the fan switch. I believe the resistor is located behind the glove box. Empty out glove box, push in clips on each side, the box will swing down, giving access to the lower portion of the dash, wires, etc.
Where is the resistor on a Jeep Liberty?
Squeeze them towards each other and the glove box opens up. (empty glove box 1st). the resistor is towards the right. There was a red locking clip on the bottom, getting this to come out was the biggest problem, it does NOT come off, just out. then remove the cable connections, then two bolts (5/16). It took me about 30 minutes total.
What does it mean when your headlights don’t work?
With that in mind, it can be tremendously useful to start off by looking at whether both, or just one, of your headlights have failed, and whether or not the high or low beam mode still works. When headlights stop working, it’s usually an electrical problem or an physical issue with the bulbs themselves.
What to do when both head lights stop working at the same time?
When that happens, the operational lifespan of your headlight capsule will be severely compromised, and the only fix is to replace the headlight assembly. When both headlights stop working at the same time, the bulbs usually aren’t at fault.
Been problem free through 73,000 miles except for the blower control. This is a 4 position switch that only the fourth position works on. Does anyone know if this sounds like a switch, or is it something more complicated? If it is a switch, I can probably change it, if not probably a trip to the dreaded dealer. Thanks
Where are the speed sensors on a Jeep Liberty?
On my 2002 Liberty is one speed sensor, placed on the top of rear differential. I had 2x problem with it. Second time it was only broken wire direct on this sensor. Fixed it by myself. Hey Guys (and Ladies), Here’s a quick question – the headlights on my 06 Liberty stay on after I leave the vehicle for 60 seconds.
We just had our 2004 Jeep Liberty in to get the power steering pump and P/S hih pressue line replaced; when we got it back from dealer, the horn wasn’t working?
Why is my brake light not working on my Jeep Liberty?
TIPM was replaced 7 months ago but exhibit no symptoms during diagnostic. Brake switch failed so that brake lights stayed on and cruise control would not work. The signal will continue to flash in the last direction the signal light lever was moved to, turn or lane change mode.
Are there any electrical problems with a Jeep Liberty?
The local Jeep Dealer is useless. I have a 2002 Liberty – one of the first off the line. This weekend, I think I blew a fuse for the interior electrical. The radio/clock, lights, locks, and alarm do not work. I was driving when it happened, and it scared the heck out of me.
What’s the problem with my Jeep Liberty window?
Many drivers also expressed a problem with window regulator failure. This was a recurring issue with the number of vehicles in which the window would either only have open or closed and the motor that operated the window would make quite an annoying sound while you’re trying to operate it.
Are there any recalls on the 2010 Jeep Liberty?
There are only two recalls that affected the 2010 Jeep Liberty, and both affected only around 20,000 vehicles. One related to a potential failure in the brakes because of a brake booster input Ron, and the other related to a hydraulic control unit that could lead to a loss of brake fluid.
Squeeze them towards each other and the glove box opens up. (empty glove box 1st). the resistor is towards the right. There was a red locking clip on the bottom, getting this to come out was the biggest problem, it does NOT come off, just out. then remove the cable connections, then two bolts (5/16). It took me about 30 minutes total.
What does it mean when your tail light does not work?
This most likely means you have a bad ground since neither tail or brake lights work. Check the black wire going to bulb for good ground using a testlight. If ground does not light up testlight run a new ground. Let me know if you have any questions, thanks. Dan its the tail light which is also the brake light AND the left parking light up front.
Is the left tail light and parking light the same?
(Same Bulbs (2) as the parking Light) left TAIL light, left PARKING light does not turn on when i turn the headlights on with the standard 2 position pull knob on the dash. It only effects the left side of the car. Right side works properly. Check 10 amp fuse in location 7 of fusebox, this is for park lamps on left side.
What are the new tail lights on a jeep?
On the new taillight, Black was the running light, White was the brake, turn and flasher and Red was the ground wire. Happy hunting! Keep us posted. :thumbsup:
Are there no tail, parking OT dash lights?
No announcement yet. NO tail, parking ot dash lights!!! NO tail, parking ot dash lights!!! I’m John and a newb to the forum. I own a 2000, a 2002 and a 2008 Wranglers. They are driven by the wife and my 2 children, which sort of leaves me walking.
What are the running lights on a jeep TJ?
For this vehicle (2000 TJ), running lights (ie: when the headlights are on) are Black. Turn signal, brake and flashers are Green on the left and Brown on the Right. Back up is Purple.
On the new taillight, Black was the running light, White was the brake, turn and flasher and Red was the ground wire. Happy hunting! Keep us posted. :thumbsup:
The following are warning lights and indicators found in vehicles built by Jeep. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are nearly 80 of them so be patient!
How do I Turn on Dash, tail and parking lights?
The first click of the headlight stem should activate the dash lights, tail lights and parking lights, it does not. The second click should and does activate the headlights. However the dash, tail and parking lights still do not come on.
Where are the running lights on a quadratec Jeep?
On the left, I used a ring connector and screwed the plate mounting screw to the connector. On the right, another ring connector was used with a small sheet metal screw through the backside of the wheel well. On the new taillight, Black was the running light, White was the brake, turn and flasher and Red was the ground wire.
Where are the ESC lights on a jeep?
There are 2 ESC lights on the cluster. One controlled by the switch on the dash which says “off” under the picture of the jeep with skid marks under it (signifying that the ESC system was manually disabled) and another identical looking light but the word “off” is not displayed under it. This is the light that is on.
What is the malfunction indicator light on a Jeep Liberty?
The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position, before engine start.
When does the oil chime sound on a Jeep Liberty?
The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine.
When to cycle the shift key on a Jeep Liberty?
This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off.
Where is the fuse box on a Jeep Liberty?
Jeep Liberty (2008) – fuse box diagram Year of production: 2008 Totally Integrated Power Module (TIPM) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery.
Why is my brake light not working on my 2005 Jeep Liberty?
It would seem that the contact overheats and melts into the plastic housing, causing a potential fire issue and resulting in no contact to make the light bulb work. See all problems of the 2005 Jeep Liberty .
Are there any problems with the Jeep Liberty?
Other Common Exterior Lighting related problems of Jeep Liberty Problem Category Number of Problems Headlight Switch problems 15 Tail Light Switch problems 12 Turn Signal problems 8 Fog Light Switch problems 4
Why is the brake warning light on on my Chevy Tahoe?
If it’s engaged, the brake light will stay lit. If the handle isn’t all of the way down, it’ll cause the brake warning light to stay on. Check to make sure that there isn’t the little bit left that it needs to turn the brake light off.
Why are the brake lights on my Jeep Liberty going out?
The contact owns a 2005 Jeep Liberty. The contact stated that the brake lights had gone out completely. The service station stated that the light bulbs failed and they replaced the bulbs. The current mileage was 66,000 and the failure mileage was unknown. The contact owns a 2005 Jeep Liberty.
Where are the fuses on a Jeep Liberty?
Jeep Liberty (2004) – fuse box diagram Year of production: 2004 Interior Fuses The fuse panel is on the left side of the instrument panel. Cavity Ampere rating [A] Description 1 15 Horn Relay, Power Sunroof Relay, Power Window Relay 2 10 Rear Fog Lights (Export Only) 3 20 Cigar Lighter 4 10 Headlight Low Beam Right …
When did I get my 2004 Jeep Liberty?
It was handed down to me during senior year of HS in 2014 and has taken me from California to my current home in Chicago. Its been there through the good and bad of my life. The lack of traction control, ABS and 4WD means that it’s fun to drive, especially in rain and snow.
The Liberty was fairly popular in its day, but it was not without its problems as well. If you’re interested in picking up a used Liberty for yourself, it’s good to be familiar with the problems that the various model years were faced with.
Jeep Liberty (2004) – fuse box diagram Year of production: 2004 Interior Fuses The fuse panel is on the left side of the instrument panel. Cavity Ampere rating [A] Description 1 15 Horn Relay, Power Sunroof Relay, Power Window Relay 2 10 Rear Fog Lights (Export Only) 3 20 Cigar Lighter 4 10 Headlight Low Beam Right …
What was the rating of the Jeep Liberty in 2006?
Based on the Insurance Institute for Highway Safety crash testing, the 2006 Jeep Liberty was also poorly rated, in particular is it related to rear crash test results. The Jeep Liberty fared a little bit better in 2007 than it did in 2006 in terms of problems reported by drivers.
Why is my passenger side brake light not working?
The brake light (passenger side) went out. I replaced the bulb and the other one while I was at it. But the passenger side brake light still doesn’t work. Even tried switching bulbs to use the one that I knew was working on driver’s side, but still wouldn’t work on passenger side. I see that there’s only one fuse control for both lights.
How to change the brake light on a Jeep Liberty?
Brake light replacement. Needed: Sylvania 3157 bulb, 10mm socket, T-20 star bit. Wrench. I used a power wrench but a manual socket wrench works fine too. Takes 5 minutes. Same process works for changing amber light or tail light. This is a 2011 Jeep Liberty but the process is the same for 2008, 2009, 2010, 2011, and 2012 Jeep Liberty. Loading…
The brake light (passenger side) went out. I replaced the bulb and the other one while I was at it. But the passenger side brake light still doesn’t work. Even tried switching bulbs to use the one that I knew was working on driver’s side, but still wouldn’t work on passenger side. I see that there’s only one fuse control for both lights.
Why are the rear lights on my car not working?
The causes for dysfunctional rear lights are: 1 Burnt bulbs 2 Blown out fuse 3 Damaged wiring 4 Electrical issues
Is it illegal to drive without a brake light?
First of all, you will get pulled over and be fined by a police officer since it is definitely illegal to drive without a working brake light. Second of all, other drivers cannot see you very well in the dark. Without brake lights, it is impossible for them to know whether you are stopping or not, so accidents on the road are very likely.
Which is the worst year for Jeep Liberty?
The 2006 model year has the most overall complaints for all model years, and is commonly rated as the worst model year depending on the severity of heat issues, the repair cost for any problems, and the average mileage at which the problems generally occur in the car.
Why are the lights on my Jeep Liberty not going off?
A Jeep Liberty’s Interior Lights Won’t Go Off. If the interior lights on your Jeep Liberty stay on, there could be three possible issues: the fuse is stuck, one of your doors is open, or the light switch is set to the “ON” position. All three of these issues have very simple solutions that should not take more than ten minutes to solve.
How do you turn off the lights on a Liberty?
Open and close all of the Liberty’s doors. Make sure every door is closed all the way. If the lights are still on, you may need to check to the light switch. Press the light switch on the headlamp control panel. It should be fully depressed for the lights to be off.
On my 2002 Liberty is one speed sensor, placed on the top of rear differential. I had 2x problem with it. Second time it was only broken wire direct on this sensor. Fixed it by myself. Hey Guys (and Ladies), Here’s a quick question – the headlights on my 06 Liberty stay on after I leave the vehicle for 60 seconds.
Why does my Jeep horn sound all the time?
The TIPM is Chrysler ’s Totally Integrated Power Module, used in newer Jeeps. It’s the relay center that sends power to the windows, door locks, horns, and many other electronic parts. If the TIPM malfunctions, it can cause the horn to honk at random, the windows to roll up and down, and the doors to seemingly lock and unlock themselves.
What kind of problem does a Jeep Liberty have?
210-horsepower 3.7L V6 4-speed automatic 4WD, part-time w/low range rear window would not go up or down. Covered under manufacturere’s warranty both front door windows coming off track during closing. Replaced window glass and track or fixture inside front doors. Seems to be a common problem with 2007 Liberties.
When did my car horn stop blaring?
Nothing happened until I closed the hood, shut the garage door and start to go inside, and the horn starts blaring continuously. I have the fuse pulled again for the time being. The battery was replaced in early September and the horn issue started randomly in October (I got back in November).
Why do the lights flash on my Jeep Liberty?
As Farout stated, the Tech may have left it in the ON position, try one click first. My wife and I have a 2002 Liberty and have noticed that the dash lights flash when the lights are on sporadically.
How to change speed sensor on Jeep Liberty?
Empty out glove box, push in clips on each side, the box will swing down, giving access to the lower portion of the dash, wires, etc. OK the dealer fixed the speed sensor for the third time on his dime claiming that now all 3 speed sensors have been changed.
What to do if your Jeep Liberty stops running?
Just like the air shut the nibble off before it stops flowing. By the way use a long hose like a oversized aquarium hose on the end of the nipple to a container below the the jeep, or some rags to catch the fuel. Or one will smell fuel for a few days. Make sure the air nipple is closed tight and try to start it again.
Nothing is wrong with the fan switch. I believe the resistor is located behind the glove box. Empty out glove box, push in clips on each side, the box will swing down, giving access to the lower portion of the dash, wires, etc.