Where is the water pump located on a Pontiac?
The Pontiac car is a compact vehicle, so a number of parts and components are installed within close proximity. The water pump on the Pontiac car is connected to the thermostat housing, so you must work with both of these parts to replace the water pump.
How to tell if a car’s water pump needs replacement?
How to Tell if a Car’s Water Pump Needs Replacement. Your car’s water pump is an important part of your vehicle. It is the part that continually pumps coolant to your vehicle’s engine so that it doesn’t overheat.
How do you install a water pump on a car?
Align the bolt head of the long bolt up with the hole in the frame rail to remove it. Remove the water pump bolts and the water pump. Squeeze some sealer around the outer edge of the water pump and install the pump with a new gasket into the engine, tightening the long bolts to 22 foot pounds (30 Nm) and the short bolts to 11 foot pounds (15 Nm).
What does it mean if your car water pump is leaking?
A puddle of water found beneath your car on a hot day may not indicate a water pump or coolant system problem. When your air conditioning system runs in your car, condensation occurs. This condensation leaks out beneath your car and is perfectly normal.
When did the Pontiac Grand Prix come out?
In this article, we consider the sixth-generation Pontiac Grand Prix, produced from 1997 to 2003. Here you will find fuse box diagrams of Pontiac Grand Prix 1997, 1998, 1999, 2000, 2001, 2002 and 2003, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Where is the fuse box on a Pontiac Grand Prix?
Pontiac Grand Prix (2004-2008)…>>. Cigar lighter / power outlet fuse in the Pontiac Grand Prix is located in the Instrument panel fuse box (see fuse “CIG LTR”). It is located in the glovebox, behind the cover on the right.
What kind of carpet does a Pontiac Grand Prix have?
The bucket seats were upholstered in Morrokide vinyl, while nylon loop-blend carpeting covered the floor and lower door panels. The center console-mounted transmission shifter included a storage compartment and a tachometer.
What kind of power does a Pontiac Grand Prix have?
The standard 350 hp (260 kW) 400 cu in (6.6 L) V8 was revised to meet the new 1968 Federal and California emission regulations. Both optional 428 cu in (7.0 L) V8s received higher power ratings of 375 hp (280 kW) for the base version and 390 hp (290 kW) the HO. Interior trim only received minor changes from 1967 aside from revised door panels.
How to tell if a car water pump is bad?
If a car’s water pump is bad, the pump will usually leak, the engine compartment may make a whining noise or the car may be overheating. Learn about the variety in difficulty of replacing water pumps with help from an ASE-certified technician in this free video on troubleshooting car problems. Expert: Chuck Orlandi.
How big is a water pump on a car?
Attach the water pump pulley, tightening the bolts to 115 inch pounds (13 Nm). Reattach the engine mount bracket, tightening the nut that is positioned the closest to the air-conditioning compressor to 33 foot pounds (45 Nm) and all others to 58 foot pounds (78 Nm).
How to replace the water pump in a Grand Prix?
Learn more about removing and replacing the water pump in your Grand Prix, including proper tightening procedures for different engines. Park your Grand Prix on level ground. Gather your tools for easy access and disconnect the negative battery cable.
Can a power steering pump be removed from a Grand Prix?
On Grand Prix models equipped with the 3.8-liter engine, removing the power steering pump will help you access the water pump. This is optional. If you do remove the power steering pump, the bolts must be tightened to 25 foot-pounds of torque when replaced. Use caution when working with engine coolant.
How do you remove a pulley from a water pump?
Loosen the bolts on the pulley, but do not remove them. Once the pulley bolts are loosened, turn the pulley to remove the accessory belt, and then finish removing the pulley. Set the pulley and its bolts aside. Remove the five bolts (all models) mounting the water pump.
Where is the coolant drain plug on a Grand Prix?
Park your Grand Prix on level ground. Gather your tools for easy access and disconnect the negative battery cable. Place your drain pan underneath the radiator and locate the coolant drain plug. Newer models will have a plastic guard to remove before you can access underneath the front of the engine bay.
How do you remove water pump pulleys on radiator?
Slide the drain pan under the radiator petcock. Open the petcock and allow the antifreeze mixture into the drain pan. Close the petcock. Loosen the water pump pulley bolts, but do not remove them. Loosen the belt tensioners on the accessory drive belts.
How do you remove coolant from a water pump?
Remove the accessory drive belt and disconnect the coolant hoses from the water pump. Loosen and remove the water pump pulley bolts and remove the pulley. Align the bolt head of the long bolt up with the hole in the frame rail to remove it. Remove the water pump bolts and the water pump.
What happens when the water pump fails in a car?
When the water pump fails or is beginning to wear out, it can lead to complete engine failure. When the water cooled (as opposed to air cooled) engine was introduced, many automotive experts believed that the water pump circulating coolant through the engine block was just as critical to engine protection as oil.
Where does the coolant go in a water pump?
1. Coolant Leak at the Front-Center of your Car. The water pump is comprised of multiple gaskets and seals that keep coolant contained and ensure that consistent flow of coolant is delivered from the radiator to the engine.
What to do if your car water pump is leaking?
If you notice there is a leak of coolant (which will appear to be green or sometimes red in color) under the center of your car, truck or SUV, contact a professional mechanic to inspect this problem. More often than not, it’s a leak from the water pump that can be repaired before it gets worse.
What should I do if my water pump is not working?
As discussed above, an engine will maintain a consistent temperature when the water pump works correctly and circulates water to a functioning radiator. If you notice steam coming from the front of your motor, you should pull over to a safe area and contact a mechanic as soon as possible.
What happens if you don’t replace a water pump?
Failure to replace a malfunctioning water pump puts the engine at risk of overheating, because it won’t always receive the proper amount of coolant. Slide the drain pan under the radiator petcock. Open the petcock and allow the antifreeze mixture into the drain pan. Close the petcock. Loosen the water pump pulley bolts, but do not remove them.
How do you remove a water pump from an engine?
Remove the water pump mounting bolts with the appropriate socket, then remove the water pump with from the engine. Clean the mounting surface on the engine with a screwdriver and a rag. Line the water pump-mounting surface with a thin layer of RTV silicone onto the water pump.
The Pontiac car is a compact vehicle, so a number of parts and components are installed within close proximity. The water pump on the Pontiac car is connected to the thermostat housing, so you must work with both of these parts to replace the water pump.
Align the bolt head of the long bolt up with the hole in the frame rail to remove it. Remove the water pump bolts and the water pump. Squeeze some sealer around the outer edge of the water pump and install the pump with a new gasket into the engine, tightening the long bolts to 22 foot pounds (30 Nm) and the short bolts to 11 foot pounds (15 Nm).
Attach the water pump pulley, tightening the bolts to 115 inch pounds (13 Nm). Reattach the engine mount bracket, tightening the nut that is positioned the closest to the air-conditioning compressor to 33 foot pounds (45 Nm) and all others to 58 foot pounds (78 Nm).
How do you replace a water pump cover?
Replace the seal to the recessed part of the water crossover. Insert all components in the reverse order in which they were removed. Tighten the water pump bolts to 74 foot pounds (100 Nm), the water pump cover bolts to 89 inch pounds (10 Nm), and the water pump shield fastener to 98 inch pounds (10 Nm).
What kind of car is the Pontiac Grand Am?
The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. Why dose my car keep overheating?
Why does my Pontiac Grand Am keep overheating?
I gotta 1999 pontiac grand am se 3.4 it ran ok when I first got it then seripeteen belt broke overheated a lil had problems since.got belt fixed then had problems with the fans not wrking also so hooked them up direct an found out outta 2 fans one wrked.
How do you remove a water pump from a car?
Put the nut back onto the stud, so you don’t lose it. Remove the alternator retaining bolts, alternator and alternator bracket with the appropriate socket. Remove the water pump pulley bolts, then remove the pulley. Remove the water pump mounting bolts with the appropriate socket, then remove the water pump with from the engine.
Where is the tensioner on a Pontiac Grand Prix?
Place the 15mm socket and long handled wrench on the supercharger tensioner pulley (just below the SC pulley and towards the front of the car) with the other hand. Push the wrench towards the front of car to relieve the tension on the belt. Slip the SC belt over the SC pulley. Double check the routing and fit of the belts.
How to relieve tension on the serpentine belt?
To relieve the tension on the serpentine belt, push the long handled wrench towards the rear of the car and then pull the serpentine belt off the alternator. Then pull the serpentine belt off the power steering pump, the tensioner, the water pump, the crank shaft, and the air conditioning pulley.
How do you install a new water pump?
Install the new water pump, placing a bit of bead sealer around the outside edge of the pump. Also attach a new gasket to the water pump. Tighten the long water pump bolts to 22 foot pounds (30 Nm), and the short water pump bolts to 11 foot pounds (15 Nm). Attach the water pump pulley, tightening the bolts to 115 inch pounds (13 Nm).
Failure to replace a malfunctioning water pump puts the engine at risk of overheating, because it won’t always receive the proper amount of coolant. Slide the drain pan under the radiator petcock. Open the petcock and allow the antifreeze mixture into the drain pan. Close the petcock. Loosen the water pump pulley bolts, but do not remove them.
Remove the water pump mounting bolts with the appropriate socket, then remove the water pump with from the engine. Clean the mounting surface on the engine with a screwdriver and a rag. Line the water pump-mounting surface with a thin layer of RTV silicone onto the water pump.
Install the new water pump, placing a bit of bead sealer around the outside edge of the pump. Also attach a new gasket to the water pump. Tighten the long water pump bolts to 22 foot pounds (30 Nm), and the short water pump bolts to 11 foot pounds (15 Nm). Attach the water pump pulley, tightening the bolts to 115 inch pounds (13 Nm).
How do you mount a water pump on silicone?
Line the water pump-mounting surface with a thin layer of RTV silicone onto the water pump. Place the gasket on the water pump and press it into the silicone. Install the water pump and tighten the retaining bolts to 19 foot-pounds of torque.
Put the nut back onto the stud, so you don’t lose it. Remove the alternator retaining bolts, alternator and alternator bracket with the appropriate socket. Remove the water pump pulley bolts, then remove the pulley. Remove the water pump mounting bolts with the appropriate socket, then remove the water pump with from the engine.
Slide the drain pan under the radiator petcock. Open the petcock and allow the antifreeze mixture into the drain pan. Close the petcock. Loosen the water pump pulley bolts, but do not remove them. Loosen the belt tensioners on the accessory drive belts.
How does the water pump in a Chevy Malibu work?
The water pump in your 1999 2.4 L Chevy Malibu helps cool your engine by distributing engine water to the radiator. You can check for leaks by placing white paper beneath your car overnight and checking to see if there are green coolant stains in the morning.
What’s the best way to replace a water pump?
Water Pump location, inspection, diagnosis, removal and replacement / installation explained. 1. Large Screwdriver: http://amzn.to/2igwntV 2. Metal Oil Pan: http://amzn.to/2nlDM0y 3. Gasket Adhesive: http://amzn.to/2BAc03K 4. Ratchet and socket set: http://amzn.to/2inoxOY 5. Mechanic’s Tool Set: http://amzn.to/2Bzmccg 6.
How can I improve my Pontiac V-8 performance?
Achieving that can be an arduous and time-consuming process with much trial and error, but the efforts can significantly improve a vehicle’s performance. This Tech Tip is From the Full Book, HOW TO BUILD MAX-PERFORMANCE PONTIAC V-8S.
When to start the distributor on a Pontiac V-8?
The distributor must be timed appropriately to provide peak performance and that includes initiating combustion some 30 to 40 degrees before the piston reaches TDC, depending upon the application.
What kind of springs do I need for my Pontiac V-8?
The Adjustable Vacuum Advance kit from Crane includes a variety of advance-curve springs as well as a serrated limited plate and vacuum adjustment tool. It’s an excellent piece that’s ideal for tailoring vacuum advance to provide peak engine efficiency at idle and part throttle.
Achieving that can be an arduous and time-consuming process with much trial and error, but the efforts can significantly improve a vehicle’s performance. This Tech Tip is From the Full Book, HOW TO BUILD MAX-PERFORMANCE PONTIAC V-8S.
The Adjustable Vacuum Advance kit from Crane includes a variety of advance-curve springs as well as a serrated limited plate and vacuum adjustment tool. It’s an excellent piece that’s ideal for tailoring vacuum advance to provide peak engine efficiency at idle and part throttle.
The distributor must be timed appropriately to provide peak performance and that includes initiating combustion some 30 to 40 degrees before the piston reaches TDC, depending upon the application.
What’s the best airflow capacity for a Pontiac V-8?
Those from the mid-to-late 1970s offer a maximum airflow capacity of 800 cfm or slightly more and are the best performance candidates for the cost. Originally installed on Pontiac V-8s displacing 301 to 455 ci, they all respond similarly and favorably to performance modifications regardless of original application.
Replace the seal to the recessed part of the water crossover. Insert all components in the reverse order in which they were removed. Tighten the water pump bolts to 74 foot pounds (100 Nm), the water pump cover bolts to 89 inch pounds (10 Nm), and the water pump shield fastener to 98 inch pounds (10 Nm).
How do you remove a water pump from an alternator?
Remove the main power wire from the back of the alternator with the appropriate wrench. Put the nut back onto the stud, so you don’t lose it. Remove the alternator retaining bolts, alternator and alternator bracket with the appropriate socket. Remove the water pump pulley bolts, then remove the pulley.
When did the Buick 3.8L engine start?
The Buick 3.8L has evolved from its humble beginnings as a cheap, easy-to-build, economy motor in 1962, into one of the best pushrod motors in the world. But did you know that the engine started its “life” as a Buick V8 that had two cylinders “missing”?
When did the Buick 3800 Series 2 come out?
The 3800 Series II was on the Ward’s 10 Best Engines list for 1995 through 1997. A 3800 Series II L67 Supercharged engine in a 1998 Buick Regal GS.The L67 is the supercharged version of the Series II L36 and appeared in 1996, one year after the normally-aspirated version.
How tall is a 1969 Pontiac water pump?
Using a flat object, place it against the face of the hub of the water pump as shown. Measure from that point to the rear of the water pump. This will give you the correct length (or some call it height) for the water pump you need. The early 1969 water pump was 11 bolt and measures 4″.