Where is the top motor on a convertible?
If the level drops below the MIN, the convertible top will either not operate at all or move too slowly, not close, or stop halfway. Locate the convertible top motor. In most convertibles, it is located in the trunk behind the lining. Also, check near the spare tire or behind the rear seats.
Where is the CVM located on a convertible top?
CVM: Convertible top module The convertible top module (CVM) controls all electrical and hydraulic functions of the convertible top. The convertible top module is connected to the K-bus. Convertible top module is installed on rear left side panel (removal of rear seat and side trim is necessary).
What to do when your convertible top stops working?
By the time your convertible top stops working, the leaks should be easy to identify. Inspect the hydraulic lines. Make sure they are tightly connected. The hoses should not be cracked or leaking. Address any leaks that you may find at the pump, cylinders, or solenoid. Replace any damaged or leaking o-rings.
How do you raise the roof on a convertible car?
Answer: By default, the controls for the raising and lowering of the roof on convertible cars are bound to the same button as the headlights. To raise or lower the roof on your car, the vehicle must be stationary and the button held down.
How is the convertible top raised and lowered?
The manual convertible is raised and lowered by hand (once unlatched) with the help of hydraulic gas cylinders. The top lowers and raises fully automatically by means of electrohydraulic servo units that control the primary soft-top movements. The top / windshield top rail locks are operated by an electric motor.
How do you close the convertible top on a BMW?
Closing the convertible top manually should be performed by two people. The rear seats must not be occupied. 1. Open the trunk lid. 2. Take the screwdriver out of the onboard vehicle tool kit. 3. If the convertible top is locked, release the two button in the cargo area, arrows 1, using the screwdriver and pull forcefully all the way out.
How do you raise the convertible top on a corvette?
Press and release the lock button, and then press and hold the convertible top button. The tonneau cover can also be raised remotely via the key fob by pressing and holding the lock button, and then pressing the convertible top button. This latter feature is ideal for checking fluid levels.
CVM: Convertible top module The convertible top module (CVM) controls all electrical and hydraulic functions of the convertible top. The convertible top module is connected to the K-bus. Convertible top module is installed on rear left side panel (removal of rear seat and side trim is necessary).
Why is my convertible top not moving up?
While the pump is running, the hydraulic system has air trapped in the lines. Also, this system has a major hydraulic fluid leak, and for that reason, the level drops below the MIN mark as the level drops, the convertible struggles to move up and down. Check the operation of the convertible pump motor.
How many volts does a convertible top need?
Every time you press the convertible switch, you should read between 11-13 volts at the pump. If you are not getting any current at the hydraulic motor, you may have an electrical problem or a defective switch. There are between 4 and 10 micro-switches installed in your convertible required to run your top.
Is there a way to rebuild a convertible motor pump?
In addition to offering new motor pumps, we offer a hydraulic motor pump rebuilding service. This service allows us to return your own convertible top motor to fully reliable action at less cost than a replacement motor. You can “order” the rebuild service, listed as a “part” on this page, and pay for it with your credit card or paypal.
If the level drops below the MIN, the convertible top will either not operate at all or move too slowly, not close, or stop halfway. Locate the convertible top motor. In most convertibles, it is located in the trunk behind the lining. Also, check near the spare tire or behind the rear seats.
What causes a convertible top to move slowly?
Convertible top moving very slowly. Often caused by a weak lift cylinder. It can also be caused by binding or convertible motor failure. If a convertible system may seem complicated at first, don’t let fear stop you from carrying a few basic troubleshooting steps yourself.
Every time you press the convertible switch, you should read between 11-13 volts at the pump. If you are not getting any current at the hydraulic motor, you may have an electrical problem or a defective switch. There are between 4 and 10 micro-switches installed in your convertible required to run your top.
How to operate the top switch on a convertible?
HOW TO OPERATE THE TOP SWITCH The top will work only in the “Park” or “Neurtal” positions, with key turned to “ACC” or “START”.