Where is the OBD2 port in my Jeep Grand Cherokee WK2?

Where is the OBD2 port in my Jeep Grand Cherokee WK2 (2011 – …) All vehicles are equipped with an OBD port to which you can connect your klavkarr diagnostic case. Sometimes, the most difficult thing is to find this port!

Where is the OBD2 connector on a Jeep ZJ?

To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Use our search engine below to locate your OBD2 port! You will find below several pictures which will help you find your OBD connector in your car. Compass (2016 – …) Grand Cherokee WK2 (2011 – …)

What is the location of the OBD port?

The OBD Port, is the location where you can plug in any OBD tool into the vehicle to pull vehicle information. It is also the primary location of tracking devices such as dongles as the port provides ongoing power to the device. There are two generations of OBD ports, OBD1 and OBD-ii aka OBD2.

How to diagnose a Jeep Grand Cherokee WK2?

To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Use our search engine below to locate your OBD2 port! Grand Cherokee WK2 (2011 – …)

What to do if the OBD II scanner doesn’t communicate with the vehicle?

What to do if the OBD II scanner doesn’t communicate with the vehicle. TEST 1: Connect the positive DMM lead to DLC pin 4 and the negative DMM lead to the negative battery terminal, using jumper wires if necessary. Do not connect to the body or chassis ground but to the battery terminal directly.

When do I get ” linking error ” OBDII Comm failure?

Dec 24, 2008 I have been having so much trouble with this car so I finally went out and bought a nice OBD II Scanner. Relief came when the scanner arrived but it did not last long. I booted it up correct and as it tried to connected I get “Linking Error”.

Where is the OBD plug on a Jeep Grand Cherokee?

OBD connector location for Jeep Grand Cherokee WJ (1998 – 2005) You will find below several pictures which will help you find your OBD connector in your car. The OBD socket is located under the steering wheel on the left. Go to the OBD2. scanner for JEEP. The OBD2 plug is above the hood lever.

Why is my OBD2 not connecting to YouTube?

These issues include an incompatible obd2 scan tool, bad fuses, damage in the circuit board, ECU, and failed computer. OBD-II…. Non connecting data Port Issue. *FIXED* This might help you! – YouTube OBD-II…. Non connecting data Port Issue. *FIXED* This might help you! If playback doesn’t begin shortly, try restarting your device.

How to check engine light codes on Jeep Cherokee?

Jeep Check Engine Light Codes 1 Connect scan tool to the 16-pin data link connector (DLC) located near the steering column. The connector may have a removable cover. 2 Turn the ignition on. 3 Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).

Why is my OBD 2 scanner not working?

Look in the connector and make sure you don’t have a pin that is bent and not making contact. You could also have lost the connection on the back of the OBD plug too. From what I’ve read around, a bad CPS will actually stop the OBDII from working.

Is there a scanner that can read OBD codes?

Both wires terminate in one ring terminal attached to the engine block at the oil dipstick tube bracket attach stud. It’s called G102. Will check this out – I too cant read codes with my scanner although the scanner works perfectly on my other car…Thanks You should check the two grounds (4&5) in the engine bay.

Where can I find the OBD code for my Acura?

If there is no procedure for your manufacturer specific code, then I suggest referring to a similar generic OBD II code (these are listed numerically by system type) to get a good idea of what to look for. If at this point you still need assistance use the “Get Help” link and let us know how we can help.

Where are the OBD-2 connectors located in the car?

Some connectors have been located behind ashtrays, under the passenger seat and even over by the passengers door. OBD-2 connector must have pins 4, 5 for ground connections and pin 16 for 12 volt power supply from the vehicle battery. What is OBD DTC? Prior to OBD, auto manufacturers did not standardize DTC’s (diagnostic trouble code).

How does the OBD-2 diagnostic interface work?

If the vehicle’s onboard diagnostic system detects a malfunction, a DTC corresponding to the malfunction is stored in the vehicle’s computer, as well as realtime data from the sensors connected to the on-board computer. In addition, the OBD-II interface provides a means to clear the DTC’s once maintenance has been completed.

Where is the OBD2 plug on a jeep KK?

OBD2 port Jeep Cherokee KK (2008 – 2013) – Find your plug ! Where is my OBD2 port ? All vehicles are equipped with an OBD port to which you can connect your klavkarr diagnostic case.

Where is my OBD2 port in my car?

Since the implementation of the OBD standard, each vehicle has a standard 16-pin connector, as described on our OBD presentation page. The norm states that the port must be located inside the vehicle passenger compartment.

Where do I plug in my OBD reader?

Where’s my OBD-II port? Just select your vehicle below and we’ll show you exactly where to plug in your Hum OBD Reader. If you don’t see your vehicle listed, please call (800) 711-5800 for help.

What are the pins for the OBD-2 connector?

OBD-2 connector must have pins 4, 5 for ground connections and pin 16 for 12 volt power supply from the vehicle battery. What is OBD DTC? Prior to OBD, auto manufacturers did not standardize DTC’s (diagnostic trouble code).

Navigation