Where is the obd2 fuse located?

It is located beneath the instrument panel somewhere between the left end of the instrument panel and 12 inches (300 mm) past the vehicle centerline.

Where is my OBD2 port in Mazda 2?

The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate. To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Use our search engine below to locate your OBD2 port! CX-9 (2007 – …) Mazda 2 (2015 – …)

How to remove the cylinder switch from a Mazda Protege?

ECT sensor signal characteristic (reference) Circuit Open/Short Inspection fPage 210 Door Lock Cylinder Switch: Service and Repair DOOR KEY CYLINDER SWITCH REMOVAL/INSTALLATION 1. Close the door glass completely. 2. Disconnect the negative battery cable. 3. Remove the passenger-side front door trim.

How do you check the PCM on a Mazda Protege?

PCM Inspection Using the SST (104 Pin Breakout Box) 1. Disconnect the negative battery cable. 2. Disconnect the PCM connector. 3. Connect the SST (104 Pin Breakout Box) to the PCM as shown. 4. Tighten the connector bolt. Tightening torque 7.9 – 10.7 N.m {80 – 110 kgf.m, 69.5 – 95.4 in.lbf} 5. Connect the negative battery cable.

How to change the ECT sensor on a Mazda Protege?

Place the ECT sensor in water with a thermometer, and heat the water gradually. Specification 4. Measure the resistance between the ECT sensor terminals A and B using an ohmmeter. – If not as specified, replace the ECT sensor.

What kind of inspection should I do on my Mazda Protege?

Always carry out a total inspection of the Input systems, output systems, and PCM to determine the cause of trouble. Otherwise, a wrong diagnosis will be made. PCM Inspection Using the SST (104 Pin Breakout Box) 1.

Where is the OBD2 fuse located?

One under the hood, one in the trunk and another behind the dashboard. The OBD fuse may be listed on the fuse cover as OBD II, DLC, Accessory port, 12 v power point or cigarette lighter and will most likely be located inside the vehicle. The most efficient way to locate it is check the drivers manual.

How do I turn on OBD2?

Plug the standard OBD2 connector into the vehicle’s port located under the driver’s side of the dashboard. Turn on the car to power the scan tool or code reader. If necessary, enter any vehicle-specific information requested. Many tools will ask for the Vehicle Identification Number (VIN).

How do I test my OBD port?

With a multimeter set to “ohms” check the resistance between these two terminals (the ignition must be in the off position / key removed) as shown. If there is 60 ohms (+/- 2 ohms) your vehicle is equipped with CAN communication and the gaugeART CAN OBD Link is compatible with your vehicle.

Where is the Diagnostic Link on an Isuzu?

Diagnostic Link Connector No. 78 Year range:1986 to 1990 Locations: Under the drivers side dash panel. In the center console. (Isuzu EFI) Use This Connector > Diagnostic Link Connector No. 27 Year range:1987 to 1997 Locations: Under the drivers side dash panel. In the center console. (Isuzu EFI) Use This Connector >

Where are the Isuzu engines located on the car?

Locations: Under the drivers side dash panel. Locations: Under the drivers side dash panel. In the center console. Locations: Under the drivers side dash panel. In the center console. Isuzu Engines: For a vehicle coverage list Click Here All content copyright Rennacs Limited, 2009.

When does a car have an OBD port?

To determine which one you have, if your vehicle was built and sold in the US after January 1st, 1996 you will have an OBD 2 port. This service will allow you to find the OBD2 port location.

Navigation