Where is the fuse for the ECU system?
You can find this fuse near your fuse box, usually on the lower right hand side of your footlight controls. Follow these step by step instructions for this method: This is an easier way of removing any long term memory saved in your car’s ECU system.
How do you reset the ECU in a car?
Locate and remove the cover on the fuse box. Some say to disconnect the negative (black) battery terminal to reset the ECU, but this is unnecessary. Plus, it resets everything in the car (including your stereo settings). Instead, with a fuse puller or needle nose pliers, pull the following two fuses from the fuse box:
What to do if your fuse box is clicking?
If that relay also clicks constantly, you need to run more tests. If that relay works fine, then the original relay that was in that spot is faulty. Simply replace that relay with a new one. Identify the terminals on the relay. Look at the terminal labels on the relay.
How do you take cover off Honda ECU?
Remove the cover on the fuse box by pulling the tabs outward and lifting up. Set the cover aside. Figure 1. Locate and remove the cover on the fuse box.
How do you remove the ECU fuse from a car?
Pull up gently on the fuse pullers (but don’t squeeze the top together, or they will let go of the fuse) to remove the ECU fuse. Here is a view of the fuse box from the driver’s side of the car, with the ECU fuse removed. Put it in a safe place.
Locate and remove the cover on the fuse box. Some say to disconnect the negative (black) battery terminal to reset the ECU, but this is unnecessary. Plus, it resets everything in the car (including your stereo settings). Instead, with a fuse puller or needle nose pliers, pull the following two fuses from the fuse box:
How long does it take to reset an ECU fuse?
–and a 10 mm wrench if you’re going to remove the negative battery terminal clamp. You have 2 options: 1) remove the ECU fuse for 20+ minutes (preferred); or 2) remove the negative battery terminal for 20+ minutes. Although less time might be required for reset, it seems that 20+ minutes is the common method.
If that relay also clicks constantly, you need to run more tests. If that relay works fine, then the original relay that was in that spot is faulty. Simply replace that relay with a new one. Identify the terminals on the relay. Look at the terminal labels on the relay.
How do you reset the ECU on a car?
Pull the fuse for the ECU using the fuse pullers in the fuse panel. Turn the ignition to the “On” position but don’t crank the engine (it won’t start anyway). Wait five minutes and reinsert the fuse. The “Check Engine” light will blink, then shut off. This will indicate that your ECU has been reset.
What happens if the ECU fails in a car?
If the ECU fails completely, it will leave the vehicle without engine management control, and will not start or run as a result. The engine may still crank, but it will not be able to start without the vital inputs from the computer.
What should I do if my ECU light comes back on?
Drive the car for at least 10 miles for the ecu to learn, if there is a problem with your vehicle then the check engine light will come back on and you can analyze the fault code that the ECM throws. These codes will guide you towards the root of the problem and you can begin replacing parts to try to fix the issue.
Where is the fuse for the ECU located?
Locate the fuse for the ECU using the fuse diagram on the underside of the fuse panel cover. Pull the fuse for the ECU using the fuse pullers in the fuse panel. Turn the ignition to the “On” position but don’t crank the engine (it won’t start anyway).
Pull the fuse for the ECU using the fuse pullers in the fuse panel. Turn the ignition to the “On” position but don’t crank the engine (it won’t start anyway). Wait five minutes and reinsert the fuse. The “Check Engine” light will blink, then shut off. This will indicate that your ECU has been reset.
If the ECU fails completely, it will leave the vehicle without engine management control, and will not start or run as a result. The engine may still crank, but it will not be able to start without the vital inputs from the computer.
Drive the car for at least 10 miles for the ecu to learn, if there is a problem with your vehicle then the check engine light will come back on and you can analyze the fault code that the ECM throws. These codes will guide you towards the root of the problem and you can begin replacing parts to try to fix the issue.