Where is the check connector on a Honda Prelude?
On 90–91 Prelude models equipped with 2.1L engine, the check connector is located in the engine compartment. On 92–95 Prelude models, the check connector is located in the passenger compartment behind the center console. On all models, turn the ignition On. The ECM indicates stored DTCs by flashing the malfunction indicator/Check Engine lamp.
What kind of engine does the Honda Prelude have?
The third-generation Prelude was exclusively powered by variants of the Honda B20A engine, a base carbureted version with a SOHC 12-valve valvetrain, or a DOHC variant with Honda’s PGM-FI fuel injection and 16 valves.
Where does the fifth generation Honda Prelude come from?
Honda also released a special edition fifth generation Prelude, called Motegi. The name of this special edition derives from the ‘twin-ring Motegi’ motor-racing circuit, located in Haga District, Tochigi, Japan. This track was built in 1997 by Honda as part of their effort to bring the IndyCar series to Japan.
Why did the Honda Prelude have pop up headlights?
This was the first generation of Prelude to have pop-up headlights, which allowed for a more aerodynamic front clip, reducing drag. Opening the headlights, however, especially at higher speeds, produced significantly more drag. The design retained nothing of the first generation, being considerably more aerodynamic and with large glass surfaces.
Where is the trouble code on a Honda Accord?
The ECU is located under the driver’s seat. With the ignition switch in the “on” position and the engine OFF, the red LED on the ECU will flash the trouble codes. For example, 2 flashes, pause, 3 flashes would mean code 23.
What does the blinking on a Honda control unit mean?
The LED indicates a system failure code by its blinking frequency. The control unit LED can indicate any number of simultaneous component problems by blinking separate codes, one after another.
Where is the ECU on a Honda Accord?
The ECU is located under the passenger’s seat. Codes are displayed on a series of four LEDs. With the ignition switch in the “on” position and the engine off, codes will be displayed in ascending order. Note: Red * indicates LED on.
On 90–91 Prelude models equipped with 2.1L engine, the check connector is located in the engine compartment. On 92–95 Prelude models, the check connector is located in the passenger compartment behind the center console. On all models, turn the ignition On. The ECM indicates stored DTCs by flashing the malfunction indicator/Check Engine lamp.
The ECU is located under the driver’s seat. With the ignition switch in the “on” position and the engine OFF, the red LED on the ECU will flash the trouble codes. For example, 2 flashes, pause, 3 flashes would mean code 23.
The LED indicates a system failure code by its blinking frequency. The control unit LED can indicate any number of simultaneous component problems by blinking separate codes, one after another.
The ECU is located under the passenger’s seat. Codes are displayed on a series of four LEDs. With the ignition switch in the “on” position and the engine off, codes will be displayed in ascending order. Note: Red * indicates LED on.
What does OBD I diagnostic trouble code mean?
Full list of OBD I Diagnostic Trouble Codes for your ’92 – ’95 Honda. If your Check engine light is on you may have a serious problem. Scan your codes and follow the chart to determine what the code means.
What is the fault code for a Honda Accord?
P1297 Electric Load Detector (ELD) Circuit Low Voltage P1298 Electric Load Detector (ELD) Circuit High Voltage P1300 Random Misfire P1324 Knock Sensor Power Source Circuit Low Voltage P1336 Engine Speed (RPM) Fluctuation Sensor Intermittent Interruption P1337 Engine Speed (RPM) Fluctuation Sensor No Signal
What is the code for a transmission malfunction?
Code 51 AC signal on; DL contact off (in transmission shifter with diagnostic connector jumped) Code 52, 53 and 55 Knock sensor fault Code 71 EGR system malfunction
When does the Check Engine light come on in a Honda?
This article applies to the Honda Civic (1992-2000), and Accord (1990-2002). The check engine light in your Honda offers important diagnostic information, which will alert you of a serious problem like a bad catalytic converter. However, the check engine light also appears when the fuel tank cap is loose, or a change in humidity has occurred.
Where is the Diagnostic Code on a Honda Accord?
With ignition off, insert jumper wire in service check connector terminals, located behind right side of dash on Accord, Civic and Civic Del Sol and near center console on Prelude. Turn ignition switch to ON position. Diagnostic Trouble Codes (DTCs) will be indicated by a series of long and short flashes on MIL.
Why are the warning lights still on on my Honda Civic?
Figure 1. Honda Accord instrument panel. Figure 2. Honda Civic instrument panel. This symbol just means that the parking brake is engaged. If the parking brake is not engaged and the light is still on, this is an indication that there’s another malfunction in the braking system. Likely, the brake fluid reservoir is low. Figure 3.