When to reset the maintenance required light on a Honda Accord?
It is set to trip at certain mileage intervals as long as it’s reset when the service is performed. The Accord has been around since 1976, and depending on its year, different procedures are required to reset the light. From the late 1990s until now, the procedure remains the same. Locate the key slot to the left of the maintenance required light.
How to reset the oil light on a 2003 Honda Accord?
Press the “Select/Reset” knob and hold it. The knob is in the lower-right corner of the instrument cluster. Turn the ignition switch to the “On” position, without starting the car. Continue to hold the knob pushed in for approximately 10 seconds. The “Maintenance Required” light will turn off. Release the knob and turn the ignition off.
Where are the sensors on a Honda Accord?
Fuel Tank Pressure Sensor Air Temperature Sensor ( Ambient / Intake 1 Manifold Pressure/Vacuum Sensor Power Steering Pressure Switch Throttle Position Sensor Transmission Position Sensor/Switch Variable Valve Timing Actuator Position Sensor Variable Valve Timing Pressure Switch Camshaft Position Sensor Crankshaft Position Sensor
How do I reset the maintenance required light?
The maintenance required light should be out. Depress and hold the select/reset button on the right of the instrument panel beneath the odometer reading. Insert the ignition key into the ignition while continuing to to hold the select/reset button. Turn the ignition key to the power accessory position.
It is set to trip at certain mileage intervals as long as it’s reset when the service is performed. The Accord has been around since 1976, and depending on its year, different procedures are required to reset the light. From the late 1990s until now, the procedure remains the same. Locate the key slot to the left of the maintenance required light.
Press the “Select/Reset” knob and hold it. The knob is in the lower-right corner of the instrument cluster. Turn the ignition switch to the “On” position, without starting the car. Continue to hold the knob pushed in for approximately 10 seconds. The “Maintenance Required” light will turn off. Release the knob and turn the ignition off.
The maintenance required light should be out. Depress and hold the select/reset button on the right of the instrument panel beneath the odometer reading. Insert the ignition key into the ignition while continuing to to hold the select/reset button. Turn the ignition key to the power accessory position.
How do you reset the ignition switch on a Honda Accord?
Turn the ignition switch to the ON (II) position. Select “Vehicle Settings” in the display using the arrow buttons located on the steering wheel, then press the SEL/RESET button. Select “Maintenance Reset” using the arrow buttons, then press the SEL/RESET button. Select “Reset” using the arrow buttons, then press the SEL/RESET button.
How do you reset the Honda Element maintenance light?
Press and hold the SEL/RESET knob in the instrument panel for about 10 seconds or until the maintenance item code(s) begin to blink. Release, then press and hold the SEL/RESET knob for another 5 seconds. The maintenance item code(s) will disappear and the engine oil life will reset to “100”.
How do you reset the oil life on a Honda Accord?
Continue to press the TRIP button until the REMAINING OIL LIFE is displayed. While the REMAINING OIL LIFE is displayed, press and hold the TRIP button until the OIL LIFE is flashing. While the OIL LIFE is flashing, release the TRIP button and press and hold again until the OIL LIFE is reset to 100%.
When did the Honda Accord 2003 come out?
At its introduction in 2003, it won the Car of the Year Japan Award for a record third time.
How do I reset the required maintance light?
- Turn ignition switch to the ON position
- Trip Display to TRIP A mode
- Turn the ignition switch to the OFF position
- Depress and HOLD the Trip Meter RESET button while turning the ignition switch to the ON position.
How do I Turn Off the maintenance required light on my Honda?
How to Turn Off the Maintenance Required Light on a Honda Civic. Put the key in the ignition. Press and hold the odometer reset knob. This is the knob that sticks out on the bottom right of the instrument cluster. While holding this button, turn the key to the “On” position, but do not start the engine.
How do I reset maintenance light?
Turn your vehicle’s ignition to the “acc” setting while holding the button. Do not crank the vehicle. Hold the position for five seconds and turn the ignition key off. Release the button. The maintenance light will be reset and will illuminate again the next time service is due.
Press and hold the SEL/RESET knob in the instrument panel for about 10 seconds or until the maintenance item code(s) begin to blink. Release, then press and hold the SEL/RESET knob for another 5 seconds. The maintenance item code(s) will disappear and the engine oil life will reset to “100”.
Turn the ignition switch to the ON (II) position. Select “Vehicle Settings” in the display using the arrow buttons located on the steering wheel, then press the SEL/RESET button. Select “Maintenance Reset” using the arrow buttons, then press the SEL/RESET button. Select “Reset” using the arrow buttons, then press the SEL/RESET button.