When to replace the serpentine belt on a Pontiac Grand Prix?
Pontiac Grand Prix serpentine belt replacement is required when the rubber belt begins to wear. Picture and diagram for How to Replace Serpentine Belt on V6 This is the routing of the serpentine belt on the GM L V6 engine.
How do you remove a serpentine belt from a car?
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
How is the tension set on a serpentine belt?
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
Where do I find the serpentine belt on my car?
To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.
How do you remove a serpentine belt from a battery?
Use the appropriate sized wrench or socket to loosen the nut holding the black ground cable on the negative terminal of the battery. Slide the cable off of the terminal and tuck it to the side of the battery. You will not need to disconnect the positive terminal. Locate the serpentine belt.
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
How often should a serpentine belt be replaced?
Most serpentine belts need to be replaced every 40,000 to 70,000 miles. If there are signs of the belt rubbing on something, make sure to identify and repair whatever it was rubbing on to avoid damaging the new belt.
To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.
How can I increase the tension on my serpentine belt?
Increase the tension on the belt. If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt.
Use the appropriate sized wrench or socket to loosen the nut holding the black ground cable on the negative terminal of the battery. Slide the cable off of the terminal and tuck it to the side of the battery. You will not need to disconnect the positive terminal. Locate the serpentine belt.
Where to snake the serpentine belt on a Pontiac Grand Prix?
Since the alternator is the top most accessible pulley, you want to snake the belt around every pulley but that one. GM Pontiac Grand Prix Serpentine Belt Replacement Guide A pictures illustrated guide for replacing the serpentine (accessory) belt on a General Motors Series II L V6 engine.
Is the power steering belt on a Pontiac Grand Prix?
Supercharger Belt. pontiac grand prix belt cerpentine diagram – Answered by a verified if it’s supercharged and I’ll get you the supercharger routing too. The power steering belt? doesn’t it have a serpentine belt?
How do you tighten a serpentine belt on a car?
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
Where is the tensioner on a Pontiac Grand Prix serpentine?
The smooth tensioner pulley for the supercharger belt is located below the supercharger pulley towards the front of the car. It is just behind a black ribbed idler pulley. To loosen the supercharger belt, place the 15mm socket and long handled socket wrench on the SC belt tensioner pulley.
How do you loosen the supercharger belt on a Pontiac Grand Prix?
Pull the wrench towards the front of the car to release the tension on the supercharger belt. While holding the wrench in this position, slip the supercharger belt off the supercharger pulley. If you can’t slip it off, rotate the wrench more towards the front of the car to further loosen the belt.
Pontiac Grand Prix serpentine belt replacement is required when the rubber belt begins to wear. Picture and diagram for How to Replace Serpentine Belt on V6 This is the routing of the serpentine belt on the GM L V6 engine.
The smooth tensioner pulley for the supercharger belt is located below the supercharger pulley towards the front of the car. It is just behind a black ribbed idler pulley. To loosen the supercharger belt, place the 15mm socket and long handled socket wrench on the SC belt tensioner pulley.
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
Pull the wrench towards the front of the car to release the tension on the supercharger belt. While holding the wrench in this position, slip the supercharger belt off the supercharger pulley. If you can’t slip it off, rotate the wrench more towards the front of the car to further loosen the belt.
Where is the supercharger belt on a Pontiac Grand Prix?
Route the supercharger belt over or around the outer part of the crankshaft pulley, the two idler pulleys and the tensioner pulley. Hold the supercharger belt near the supercharger pulley with one hand.
Where is the tensioner on the serpentine belt?
The tensioner pulley for the serpentine or “accessory” belt is located directly below the alternator. It is a smooth 3″ metal pulley. To release the tension on the serpentine belt, place the 15mm socket on the pulley and push the long handled socket wrench towards the rear of the car.