What kind of engine does a Mercedes SL 500 have?
SL 500 and 600 continued with their respective engines. A second facelift, introduced in late 1998, comprised new external mirrors, 17″ wheels and new bumpers. Also new were the engines, SL 500 with a M113 5.0 L 24-valve SOHC V8 (225 kW (306 PS; 302 hp) at 5,600 rpm). The V12 engine remained unchanged.
How much fluid can be pumped through a suction line?
General engineering practice holds that suction line mean fluid velocities should be limited to 5 to 8 feet per second, or alternatively, the suction line frictional head pressure loss should ideally be limited, if at all possible, to what would be equivalent to 2 to 3 feet of the pumped liquid.
What happens if you open the hardtop on a Mercedes SL500?
If either of these are open, the retractable hardtop cannot operate. Once the lid and cover are shut, the hardtop switch may be used. Start the vehicle’s engine, and let the car run while you open or close the hardtop. The hardtop does not operate if the car’s battery voltage is too low.
Where are the elbows on a double suction pump?
Direct connection of elbows should always be avoided. In double suction pumps, if directly connected elbows can not be avoided, they should be installed such that the elbows are in a plane perpendicular to the pump shaft.
What kind of fuel pump does a Mercedes 500SL use?
In order for any fuel injected four stroke engine to run the fuel injectors must be supplied with fuel pressure. On our 500SL and SL500 Mercedes Benz uses two identical fuel pumps attached in series to provide adequate fuel pressure and fuel volume to the fuel injection system.
What do you need to remove fuel pump?
While the assembly is hanging down remove the two 6mm fasteners (green arrows) and two 8mm fasteners (yellow arrows) that hold the power and ground supply to each of the two fuel pump motors. Then remove the wiring from the terminals on the fuel pump.
How long did it take to remove ABC pump?
Total time taken to remove and reinstall the pump was about 5 hours and 2 beers, including taking pics and notes. I spent another hour or so filling and bleeding the ABC and power steering.
How do you remove an ABC pump from a Mercedes Benz?
Loosen the hose clamps from the 2 hoses where they go to the power steering reservoir and ABC reservoir, then pull the hoses from them. Remove the front 2 of the three 10mm bolts holding the reservoir assembly in the car, then loosen the 3rd nut that attaches the bracket to the strut tower.
How did the Mercedes SL500 get its name?
The SL name started as the 300SL (W198) in 1954. It was based on the 300SL race car which had gull wing doors to satisfy the race requirements to have functional doors. Since it had a tubular frame the doors had to open up, instead of out. It had a straight six.
When did Mercedes Benz stop making the 300 SL?
For the original 1954–1963 300 SL (W198 model range), see Mercedes-Benz 300 SL. The Mercedes-Benz R129 SL is a roadster which was produced by Mercedes-Benz from 1989 until 2001. The R129 replaced the R107 in 1989 and was in its turn replaced by the R230 SL-Class in 2002 for the 2003 model year.
Is the Mercedes SL500 engine a hemi engine?
Yes it’s got a hemi and more. “Hemi” is a trademark used by Chrysler and Dodge for their 1960’s engine which first used hemispherical combustion chambers to get more power. The Mercedes SL500 engine also uses hemispherical combustion chambers, although they don’t use the “Hemi” trademark.
How many valves does a Mercedes SL500 have?
(source: page 22, Mercedes 1992 Sports Models brochure). The old Chrysler Hemi only had two valves per cylinder, pushrods, carburetors and only one cam. The 1990 – 1998 SL500 has twice as many valves, no pushrods or rocker arms, fuel injection and four cams.
How much horsepower does a BMW SL500 have?
This dwarfs BMW’s 12 cylinder 5.0l engine (1989 – 1994) which only has 296 HP and 332 ft-lbs of torque. The SL500 accelerates smoothly and brutally at any speed. Acceleration comes from torque, not horsepower.
What kind of car is the Mercedes SL500?
The Mercedes-Benz SL500, part of the SL-Class of roadsters, is a two-door car classified as a luxury grand tourer. The SL500 comes with a variety of features, such as a retractable hardtop. This hardtop is operated by pulling up on a switch to open it, or pressing the switch down to close it. If you cannot get the
What’s the top speed of a 1991 Mercedes SL?
To exceed 150mph, a 1991-2 Mercedes SL customer must opt for the V8. Demand does seem slightly higher for these eight cylinder variants. A major London-based dealer dispelled all those “wait for two years, and may be you’ll to on the waiting list,” warnings.
Is there a series 107 Mercedes Benz 500SL?
Years The Series 107 Mercedes Benz 500SL Was Produced: SAVE BIG $$$$$$ IN REPAIR AND MAINTENANCE COSTS!!!
Why is my 1991 500SL having difficulty starting?
I am having some difficulty with starting my vehicle (1991 500SL from Europe), it will crank for a long time when it is cold but not start. If you keep cranking for about 5 minutes (not non stop) it will fire up, but is very unsteady and will stall if you try and give it any gas.
Where can I find a 1991 Mercedes AMG 500SL 6.0?
Spotted in San Diego, California is a 1 991 Mercedes AMG 500SL 6.0 for $89,000 USD. The selling dealer states this car has only 21,740 original miles. The exterior is blue/black metallic and the interior is anthracite leather. This special ordered car was originally delivered to the Kingdom of Jordan for the Royal Family.
What kind of engine does a Mercedes 500 SL have?
4) in 1991 the model with 2-door convertible body and V-8 4973 cm3 / 303.9 cui engine size, 240 kW / 326 PS / 322 hp (ECE) of power, 450 Nm / 332 lb-ft of torque, 4-speed automatic powertrain offered since September 1991 for Europe .
What should idle speed be on Mercedes 500SL?
If the voltage is c. 70% of the battery voltage, then the fuel injection ECU recognizes that the throttle is closed, and it should be in its idle control routine. The next step is to measure the current output by the ECU to the idle speed control valve — it should be 700-1000 milli-amps.