What kind of belt does a Mazda 6 use?
I replaced the belt/serpentine tensioner pulley, idler pulley, serpentine belt, and spark plugs on a 2003 Mazda 6 2.3l car. This engine had 115k miles. I don… AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features
Why does my Mazda 6 engine belt Rattle?
As for the belt, it could have been changed earlier in its life; same goes with the pulleys, but i could be wrong. Anyway, the issue we had with this vehicle was, during cold startups in the morning, or Winter, a rattling noise was heard coming from the engine bay during take off at around 2,000 RPM.
How much does a Mazda Protege alternator cost?
This is a how-to video on a 1999-2000 Mazda Protege 1.8L Sedan. It is very easy to install and replace your alternator and belts. Total for parts was $200 from my local auto parts store. at the dealer this would be 500-600. I hope this helps. Please Rate Comment and Subscribe! Loading…
What did I do to my Mazda 6 engine?
I replaced the belt/serpentine tensioner pulley, idler pulley, serpentine belt, and spark plugs on a 2003 Mazda 6 2.3l car. This engine had 115k miles. I don… I replaced the belt/serpentine tensioner pulley, idler pulley, serpentine belt, and spark plugs on a 2003 Mazda 6 2.3l car. This engine had 115k miles.
I replaced the belt/serpentine tensioner pulley, idler pulley, serpentine belt, and spark plugs on a 2003 Mazda 6 2.3l car. This engine had 115k miles. I don… AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features
I replaced the belt/serpentine tensioner pulley, idler pulley, serpentine belt, and spark plugs on a 2003 Mazda 6 2.3l car. This engine had 115k miles. I don… I replaced the belt/serpentine tensioner pulley, idler pulley, serpentine belt, and spark plugs on a 2003 Mazda 6 2.3l car. This engine had 115k miles.
What happens if you get the crankshaft pulley loose?
If you get the bolt loose and you turn the crankshaft or camshafts you can bent valves on multiple Mazda engines since they do not have a key. We demonstrated how to remove and get the crankshaft pulley bolt loose on Mazda CX-7 but it should work on multiple Mazda engines and models.
As for the belt, it could have been changed earlier in its life; same goes with the pulleys, but i could be wrong. Anyway, the issue we had with this vehicle was, during cold startups in the morning, or Winter, a rattling noise was heard coming from the engine bay during take off at around 2,000 RPM.
How does a crank pulley work on a Mazda 3?
There is a flat metal plate hooked onto the crankshaft pulley that has teeth on it that spins through the crank position sensor to help the ECU in determaining fuel timing and what not. You can’t just remove one and put on the new one.
If you get the bolt loose and you turn the crankshaft or camshafts you can bent valves on multiple Mazda engines since they do not have a key. We demonstrated how to remove and get the crankshaft pulley bolt loose on Mazda CX-7 but it should work on multiple Mazda engines and models.
How to change the timing chain on a Mazda 6?
1. Disconnect the negative battery cable. 2. Remove the spark plugs. (See SPARK PLUG REMOVAL/INSTALLATION.) 3. Remove the tire (RH). 4. Remove the under cover. 5. Loosen the water pump pulley bolt and removal the drive belt. (See DRIVE BELT REPLACEMENT.) 6. Remove the CKP sensor. (See CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION.) 7.
How do you suspend a chain in a Mazda 6?
1. Using a thin screwdriver, hold the chain tensioner ratchet lock mechanism away from the ratchet stem. 2. Slowly compress the tensioner piston. 3. Hold the tensioner piston using a 1.5 mm {0.059 in} wire or paper clip. Suspend the engine using the SSTs .
What’s the best tool to replace a serpentine belt?
This tool pays for itself ten times over the first time you use it to replace your serpentine belt. The serpentine belt tool kit makes it easy to precisely position idler pulleys and get belts set to the perfect tension. Fits idler pulleys requiring 15mm or 18mm hex or 3/8 in. or 1/2 in. square drives