What Jeeps have a high pinion Dana 30?
The Dana 30 that was put in the Cherokee (XJ) and Wrangler (YJ) is a high pinion, reverse cut unit and are the stoutest Dana 30’s built. The Cherokee (XJ) and Wrangler (YJ) differed in that the Wrangler (YJ) was set up for leaf spring and the Cherokee (XJ) used a coil spring setup.
What year XJ has HP Dana 30?
1999 is the last year for the “0630” head casting (The “0630” was used from 96-98, however “early” 1999 models used the leftovers and mine had the “0630” head casting which has larger exhaust ports than the later “0331” casting.)
Is high pinion stronger than low pinion?
It’s common knowledge that a high-pinion front axle is stronger than its low-pinion equivalent, but not everyone understands why. A low-pinion axle positions the pinion below the centerline of the axle, while a high-pinion axle places the pinion above the centerline of the axle.
How do I know if I have a Dana 30?
Dana 30 Axle Identification A Dana 30 cover will look like a rounded square. It should have 10 bolt holes and is 9 inches wide.
Will high pinion gears work on a low pinion axle?
Yes, exactly. The high-pinion version also has reverse-cut gears which are slightly stronger. Well the 00-01 have low pinion D30 in the front.
Can a Jeep Wrangler XJ have a Dana 30 axle?
Motive Gear Ring and Pinion Kit for 84-95 Jeep Cherokee XJ & Wrangler YJ with Dana 30 Front Axle – AFTERMARKET UPGRADE! Crown Automotive 5252508 Outer Pinion Bearing Set for 87-06 Jeep Wrangler YJ, TJ, Grand Cherokee WJ, WK, ZJ & Cherokee XJ – Left Hand Drive Applications Only!
What kind of differential cover does Jeep XJ use?
Dana Spicer 5-760X 297x / 760x Replacement Series U-Joint for 91-06 Jeep Wrangler YJ, TJ & Unlimited, 92-01 Cherokee XJ, 93-99 Grand Cherokee ZJ & WJ – AFTERMARKET UPGRADE! Riddler Manufacturing RD30 Differential Cover for Dana 30 Axles – AFTERMARKET UPGRADE!
What kind of bearing does a Jeep XJ have?
Crown Automotive J8126499 Inner Pinion Bearing Set for 76-86 Jeep CJ Series, 87-18 Wrangler YJ, TJ, JK, 84-01 Cherokee XJ & 93-04 Grand Cherokee ZJ & WJ – Right Hand Drive Applications Only!
What kind of shaft does a Jeep Wrangler use?
The Wrangler (TJ) shafts can be used in the Cherokee (XJ) and Wrangler (YJ) for a one-piece shaft with 5-297 u-joints. The 1993-1998 Grand Cherokee shafts should be avoided because they use CV joints. Grand Cherokee (ZJ), Grand Cherokee (WJ), and Wrangler (TJ) use a standard cut Dana 30.
What kind of axle does a jeep Dana use?
To get an idea of the whole differential end to end, here’s a TeraFlex Tera 30 Heavy Duty Front Replacement Axle Housing (Part TF-3503004). Note how the ends are made to accept spindles. The Dana 44 has been used on the front and rear of Jeeps.
How much does Dana 30 high pinion axle assembly cost?
Dana 30 High Pinion Non CAD Axle assembly Fits XJ, TJ, ZJ. You swap on your outer knuckles, unit bearings, and shafts. Select from drop down menus to build for your needs. Handling fee is only $50 not $200 if purchased with a rear axle assembly.
The Wrangler (TJ) shafts can be used in the Cherokee (XJ) and Wrangler (YJ) for a one-piece shaft with 5-297 u-joints. The 1993-1998 Grand Cherokee shafts should be avoided because they use CV joints. Grand Cherokee (ZJ), Grand Cherokee (WJ), and Wrangler (TJ) use a standard cut Dana 30.
What kind of suspension does a Jeep XJ have?
All XJs were built as a “Unibody” design with the body and frame rails tied together as one piece as opposed to a body on frame design. All XJs have solid axles front and rear. The suspension consists of coils for the front and leaf springs for the rear.