What is the OBDII code on a Hyundai Tucson?
P0130 is a very common OBDII code that occurs in the Hyundai Tucson. It is typically caused when the Oxygen Sensor voltage is not within normal operating conditions. Typically, the only symptom of P0130 is going to be the service engine soon light.
How to replace timing belt on Hyundai Tucson 2.7 2005?
Hyundai Tucson 2.7 2005 cambelt change instructions and replacement inteval. Full guide! Special tools None required. Special precautions Disconnect battery earth lead. DO NOT turn crankshaft or camshaft when timing belt removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated).
What is the wiring diagram for a Hyundai Tucson?
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2005-2007 Hyundai Tucson . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle.
Do you need a transponder for a Hyundai Tucson?
NOTE #1: This vehicle May Be Equipped with HYUNDAI’S TRANSPONDER ANTI-THEFT SYSTEM, check the OWNERS MANUAL for this vehcile or contact your HYUNDAI Dealer to see if the vehicle has a Special programmed Ignition Key, if it does, then for REMOTE STARTING you will need the 791 BYPASS Module and an Extra Ignition key.
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2005-2007 Hyundai Tucson . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle.
NOTE #1: This vehicle May Be Equipped with HYUNDAI’S TRANSPONDER ANTI-THEFT SYSTEM, check the OWNERS MANUAL for this vehcile or contact your HYUNDAI Dealer to see if the vehicle has a Special programmed Ignition Key, if it does, then for REMOTE STARTING you will need the 791 BYPASS Module and an Extra Ignition key.
How many miles does a 2006 Hyundai Tucson have?
Mileage: 156,432 miles Body Type: SUV Color: Blue Engine: 6 Cyl 2.7 L Accident reported. 1st owner purchased on 05/30/06 and owned in FL until 05/18/09 • 2nd owner purchased on 07/18/09 and owned in FL until 07/12/17. 1st owner drove an estimated 7,049 miles/year • 2nd owner drove an estimated 11,657 miles/year.
What is the pinout for Hyundai OBD II?
This pinout is associated with 24 compatible devices or models. Show them> Note that list is not 100% complete! * ’08 iLoad manual has VSS at pin 3. Some OBD-II cables schemes:
What happens when an O2 sensor goes bad in a Hyundai Tucson?
Oxygen sensors play a vital role in both engine management and emissions control. When an O2 (oxygen) sensor go bad, it’ll cause your Hyundai Tucson ‘s engine to run less efficiently. Your Tucson can exhibit symptoms when the Oxygen sensor has gone bad. Or, it may exhibit none at all.
What does an OBDII scanner do on a Tucson?
By using a OBDII scanner you can determine exactly which sensor is bad, and what is wrong with it. Your Tucson’s oxygen sensors are responsible for helping to keep your engine running at optimal efficiency. The engine management computer uses the data from all of the O2 sensors to keep the air/fuel mixture optimized.
Why does the Check Engine light come on on Hyundai Tucson?
Oxygen sensors can change the way that your Tucson’s engine runs. Most of the time, the check engine light will come on. It’s a good thing that the check engine light would come on, as there is more than one oxygen sensor, and they can be difficult to get to and test.