What is the ECU code for a Honda Integra?
ECU code: PCT. ECU Socket Type: OBD-2A(1996-1998 models) / OBD-2B(1999-2000 models) Note: This engine uses the same block as the Integra Type R (B18C5), which is taller than the B16a block (by approx 17 mm), but with a crank the same stroke as the b16a.
Is the Integra Type your engine the same as the B16A?
Note: This engine uses the same block as the Integra Type R (B18C5), which is taller than the B16a block (by approx 17 mm), but with a crank the same stroke as the b16a. It uses longer rods to accommodate for this, which is why the Rod/Stroke ratio is higher than a standard B16. Note: Only offered with SiRs with automatic transmissions.
Which is the intake solenoid valve on a Honda Integra?
ICS – (Intake Control Solenoid) H22A White — Empty Slot For Civic/Integra 20. PCS – (Evap Purge Control Solenoid Valve) Red 21. ICM – (Ignition Control Module) Red / Green
Is the B18A part of the B series?
The B18A is not considered part of the modern B-series family. This engine shares many characteristics with the B20A/B21 JDM version is marked B18B on the block without any number. JDM version has a compression 9.4:1 where the usdm version is 9.2:1.
What kind of engine does an 88-91 Honda Civic have?
This section includes the specs on all the most common engine swaps into a 88-91 4th Gen Honda Civic. This section also shows you what the stock Honda Civics’ came with. 10.4:1c.r. The 1.5L DX engine is by no means a performance engine. This engine was made for good gas mileage and reliability which it excels at.
Can a civic engine be swapped for a B16A?
Well the B16a sounds nice but it is NOT a direct bolt on to the 88-91 Civics. You will need engine mounts, wiring harness and other little parts that will give you a major headache. I recommend this swap to anyone that has extensive knowledge about Honda engines, or better yet have a professional swap it in.
What kind of engine does a Civic EX use?
The D16Y8 is very similar to the D16Z6 except for it was produced in the 96-00 Civic EX. It has slightly different specs as well. When installing into a 4th Gen Civic a p28 ECU (92-95 Si/EX) is used. Please refer to D16Z6 instructions for installation.” The ZC engine came stock in the Si’s in Japan.
Can a ZC engine be swapped in a civic?
The ZC engine came stock in the Si’s in Japan. With 135hp on tap a 4th gen will scoot the 1/4 mile in the 15’s with basic mods. This engine is a direct bolt on. You will want to change the ECU to a Integra ECU and the best bet is to have a SI trans.
What kind of engine does an Acura Integra have?
Acura Integra Type-R 1998-2001 B18C PR3-2 Motor with… Honda Integra DC2 Type R Spec R 98+ 5-Bolt 5 Lug Hub… 1994-2001 Honda Integra/Acura Integra. Other models may apply, please verify fitment prior to purchase.
What kind of engine does a JDM Integra have?
VTEC 2.3L JDM Honda Accord 1998-2002 BAXA MAXA MCJA… Buyer must determine compatibility into his / her vehicle. Used JDM Honda Accord SIR DOHC H23A 2.3L VTEC OBD2… Buyer must determine compatibility into his / her vehicle. JDM B18C Acura Integra Type-R 1998-2001 PR3-3 Motor…
Can a Honda Integra be swapped with a Honda Civic?
All Integra’s 1994 and up and Civic’s 1992 and up all use hydraulic transmissions. Therefore its not compatible with 4th Gen Civic’s because these vehicles have cable transmissions. To complete the swap a B-series cable transmission will need to be used or a cable-hydro transmission conversion will need to be made.
Where can I buy performance parts for my Acura Integra?
Our extensive and continuing experience with the current and the latest performance parts for the Acura Integra from more than 60 of the established aftermarket parts manufacturers provides us with the know-how when it comes to choosing only the highest quality parts for the Acura Integra platform.
What is the ECU number on a Honda Civic?
1989-1991 Honda Civic/CRX SiR (or auto from 90-91 Integra (Xsi) Honda ECU part numbers are a series of 3 alphanumeric sections. The first block is the Honda part number denoting it is an ECU. This is almost always 37820.
What do the last 3 characters in Honda ECU mean?
The Last 3 characters denote the ECU Revision type and each character is a different indicator. The first character indicates market the ECU is intended to support. The last character indicates the version number and generally does not have any significant changes to connectivity or function.