What is EC mode on hot tub?
EC: Economy – Spa will heat ONLY during filtration settings. It will heat to the set temperature and the spa may cool down until the next filtration cycle. Heating will resume again in 12 hours.
How do I get my Balboa spa out of EC mode?
To exit, press the light button or wait for 10 seconds to go back to the Main Screen. To check, next to range there is an arrow – if pointing down its in low range, if pointing up its in high range. Remember allow 1 degree per hour to heat back up when changing from low range to high range.
Why is my hot tub on economy mode?
ECONOMY mode heats the spa water during filter cycles only. If your spa is set for 100 degrees, any time the water drops below 100 the heater will come on and run until the water temperature reaches your set temperature. Standard mode is displayed as ST or STD on your topside control.
What does EC mean on a strong spa?
Economy Mode
Economy Mode “Ec” or “Ecn” will appear solid when the temperature is not current and will alternate with the temperature.
How do you reset a strong spa?
Press the RESET button on the GFCI. The GFCI will reset and the spa will turn back on. The spa is now safe to use. If the GFCI trips while the spa is in use, press the RESET button.
How do you reset the EC code on a hot tub?
Why does my hot tub says EC?
- Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode.
- DR or DRY.
- You can reset a hot tub control panel by switching it off, waiting for between 10 and 20 seconds and then switching it back on again.
How do I get my master spa out of sleep mode?
Locate and open the panel with your pool or hot tub pump timer. This should be located close to the pool pump itself and the hot tub. Set the on and off switches to the desired times. Disengage the time dial and set it to the current time.
How do I get my hot tub out of sleep mode?
On them you need to press the ‘TEMP’ button and then the ‘LIGHT’ button within three seconds of each other and this will change the modes from EC (economy mode), to SL (sleep mode) and finally to ST (standard mode) which is what you want.
Does economy mode on hot tub save money?
Preventing Expensive Energy Bills Many spas also come equipped with a hot tub economy mode, which can help you reduce your costs. Look out for hot tubs with unnecessary features, as these can increase your electric bills.
What does PR mean on a strong spa?
Priming Mode
REMOVING TRAPPED AIR BUBBLES Turn the spa on and wait for PR (Priming Mode) to appear on the topside display. Press the JETS1 button to turn on the pump, then let it run for 10 seconds.
Why does my hot tub keep going into sleep mode?
When you enter a hot tub or sauna, your body’s core temperature rises. When you get out, it begins to drop as the hot water and sweat evaporates from your skin. This cooldown mimics the same cooldown your body naturally experiences at night when it’s time to start getting sleepy.
How do I get my hot tub off EC mode?
You want it in Standard mode, so press the temp button and the light button within 3 seconds of one another and it will sequence to the next mode, repeat till you are in Standard mode. In Ec it will only heat in filter cycle In Sleep mode nothing works so do not use that. That mode is for cleaning and replacing filters.
Why does the EC button not turn on?
“If you have a control unit where the EC button remains illuminated you most likely have a stored DTC code or a version coding error for refrigerant level sensor. In order for the compressor to be turned on DTC codes need to be cleared and the coding needs to be corrected.”
Is there a way to switch out of S mode?
If you want to install an app that isn’t available in the Microsoft Store, you’ll need to switch out of S mode. Switching out of S mode is one-way. If you make the switch, you won’t be able to go back to Windows 10 in S mode. There’s no charge to switch out of S mode. On your PC running Windows 10 in S mode, open Settings > Update & Security > …
Why does the EC light stay on all the time?
The EC light stayed on all the time. I replace the evap temp sensor and reg temp sensor, thanks to sleepwalker’s help. Then I recharged the system with freon and 46 PAG oil. By the way you must get the compressor to come on to charge the AC if your’s won’t come on, then hold down EC and Rest until the EC light goes off, the compressor will kick on.
You want it in Standard mode, so press the temp button and the light button within 3 seconds of one another and it will sequence to the next mode, repeat till you are in Standard mode. In Ec it will only heat in filter cycle In Sleep mode nothing works so do not use that. That mode is for cleaning and replacing filters.
“If you have a control unit where the EC button remains illuminated you most likely have a stored DTC code or a version coding error for refrigerant level sensor. In order for the compressor to be turned on DTC codes need to be cleared and the coding needs to be corrected.”
The EC light stayed on all the time. I replace the evap temp sensor and reg temp sensor, thanks to sleepwalker’s help. Then I recharged the system with freon and 46 PAG oil. By the way you must get the compressor to come on to charge the AC if your’s won’t come on, then hold down EC and Rest until the EC light goes off, the compressor will kick on.