What does the CPS code p0341 mean?
This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor.
What is the p0341 Honda camshaft position sensor?
P0341 Honda Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.
How to fix and clear OBD-II trouble code p0341?
Often replacing the camshaft sensor fixes trouble code P0341, however it is important to check the following first: Inspect the wiring at the camshaft sensor for melting or marks of corrosion Inspect the camshaft reluctor wheel for missing or damaged teeth.
Why does my Mil come on with DTC p0341?
A damaged or stretched cam chain, resulting from infrequent oil changes, can cause the MIL to come on with DTC P0341 (CMP sensor A and CKP sensor incorrect phase detected). Old oil causes the cam chain to wear quickly.
This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor.
Why is my DTC p0341 CMP sensor not working?
Depending on year, make, and model, DTC P0341 or P0346 may have number of causes. Here are some of the most common. Faulty Sensor – If the sensor coil is open or shorted, then it will generate no signal. Poor Installation – A good CMP signal is highly dependent on placement.
Is there a p0341 code on my Savana?
Have a 2007 chevy avalanche 5.3 lit with stored DTC,s P0016 & P0340.Pending P0340 and P0341 codes. MIL has been going on and of for months with no drivability problems have a innova 3130 scanner that … read more
What causes a p0341 DTC on a Mustang GT?
Ford Trucks / Mustang GT – An alternator phase problem, such as a blown diode or open coil, may cause so much electrical interference that the CMP signal gets distorted, causing a P0341 / P0346 DTC to set, among others, in spite of there being no actual problem with the CMP sensor or wiring.
When does PCM set trouble code p0341?
As certain points of the reluctor wheel pass by the camshaft sensor, the sensor regulates 5 volt reference voltage in a wave pattern. Anytime the camshaft sensor signal does not correspond to the signals received from the crankshaft sensor, the PCM sets a trouble code P0341.
Have a 2007 chevy avalanche 5.3 lit with stored DTC,s P0016 & P0340.Pending P0340 and P0341 codes. MIL has been going on and of for months with no drivability problems have a innova 3130 scanner that … read more
What does the code po341 mean on a car?
PO341 code – cruise control kicks off, engine light and vsa lights go on. There could be an issue with the cruise control switch and the brake switch. The VSA light refers to the brake system and the light maybe coming on for the brake switch not functioning properly causing the cruise control switch…
When does the cam code 341 come back?
The egr and maf codes are gone, but the cam code 341 still comes back after about 5-8 miles when the car stumbles and gags, it then recovers for a sho… My Camry dies after 20 minutes of driving and then has to sit for a half hour or so before it can start up again.
What does the p-0340 trouble code mean?
The P-0340 trouble code indicates that the signal to and from the camshaft position sensor and the PCM is broken. When this occurs, the ignition spark and fuel injector timing will fail and the PCM will store the P0340. This will trigger the illumination of the Check Engine Light.
How does the camshaft position sensor ( CPS ) work?
The camshaft position sensor (CPS) sends a wave signal (5 volts) to the PCM for every Top Dead Center (TDC) position of the compression stroke, as well as pulse waves indicating the position of the cam sensor. Signals are generated through a reluctor wheel attached to the camshaft.
How to diagnose p0341 on a 2009 VW?
P0341 Code: Camshaft Position Sensor ”A” Circuit Range/Performance (Bank 1 or Single Sensor) – In The Garage with CarParts.com How to diagnose P0341 on a 2009 VW CC
How much does it cost to repair a p0341 Chevy?
The cost to diagnose the P0341 CHEVROLET code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
How long does it take to get a p0341 Volkswagen engine code?
Sometimes and in some models, low battery voltage or a weak starter can trigger a Camshaft Position Sensor code. The cost to diagnose the P0341 VOLKSWAGEN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
What does misfire code p0303 mean on VW TSI?
What you want to do is take the ignition coil from any other cylinder, say cylinder 3, and swap it with the coil in cylinder 2. If the misfire code moves the new cylinder (P0303), that means it’s a bad ignition coil. If the misfire stays on cylinder 2 (P0302) that means it is not the ignition coil.