What causes the p0340 code on a Saab 9-3?
Saab 9-3 P0340 Causes As stated above, the P0340 code is often caused by a failure in the Camshaft Position Sensor itself. Here are the most common causes: Wiring Issue– The Camshaft Position Sensor wiring is exposed to harsher conditions than a lot of the wiring in your 9-3.
What does CPS code mean on Saab 9-3?
The Saab 9-3 is no exception to this rule. That’s because it’s a generic powertrain code. Generic codes tell you that there is a problem, but they don’t really tell you what particular part of the system is throwing the code. OBDII P0340 means that there is a problem with the Camshaft Position Sensor (CPS) circuit.
What is the Check Engine Light code on a Saab?
Just bought 2002 SAAB 9-3 SE 4 cyl with known check engine light code P0340 pointing to camshaft sensor. The documentation suggests that there is no camshaft sensor and DIC (spark plugs acts like one). Car starts and runs very well.
How long does it take to diagnose a Saab camshaft sensor code?
Sometimes and in some models, low battery voltage or a weak starter can trigger a Camshaft Position Sensor code. The cost of diagnosing the P0340 SAAB code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
What does the p0340 code on a Saab mean?
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals. Need more information on how to fix the P0340 SAAB code?
What is the engine code for a 2003 Saab 9-3?
As far as symptoms associated with this code P0340, i am having a loss in power and what seems like a rapid misfire. Currently P0340 is the only engine code I have. Any and all help with this issue would be much appreciated. You do get codes for these, but you don’t have a cam position or separate knock sensor on this engine.
Just bought 2002 SAAB 9-3 SE 4 cyl with known check engine light code P0340 pointing to camshaft sensor. The documentation suggests that there is no camshaft sensor and DIC (spark plugs acts like one). Car starts and runs very well.
What does the camshaft position sensor on a Saab do?
P0340 Saab Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.
What to do if your camshaft position sensor says p0340?
Visually inspect the camshaft position sensor connector in search of corroded or broken connectors. Make any other repairs (if other codes are present) to make sure that other codes are not sources of the trouble code P0340. Check your camshaft position sensor’s voltage, ground, and signal readings with a multimeter.
P0340 Saab Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.
Saab 9-3 P0340 Causes As stated above, the P0340 code is often caused by a failure in the Camshaft Position Sensor itself. Here are the most common causes: Wiring Issue– The Camshaft Position Sensor wiring is exposed to harsher conditions than a lot of the wiring in your 9-3.
Visually inspect the camshaft position sensor connector in search of corroded or broken connectors. Make any other repairs (if other codes are present) to make sure that other codes are not sources of the trouble code P0340. Check your camshaft position sensor’s voltage, ground, and signal readings with a multimeter.
As far as symptoms associated with this code P0340, i am having a loss in power and what seems like a rapid misfire. Currently P0340 is the only engine code I have. Any and all help with this issue would be much appreciated. You do get codes for these, but you don’t have a cam position or separate knock sensor on this engine.
When to replace spark plugs in Saab 9-3 arc?
Spark plugs should be replaced every 60k miles on a 2004 Saab 9-3 Arc. It takes about 30min and your car will get better fuel economy versus that from worn out plugs.
Where is the ion module on a Saab 9-3?
The ION module is on end of engine, upper right rear near brake and coolant reservoir, rectangular plug wire bundle leads to coil packs.
How to change a crankshaft position sensor in 2004 Saab 9-3?
Here is a video on how to find and replace a crankshaft position sensor on a 2004 SAAB 9-3. It will also work on a few other years. A bad crankshaft position sensor can cause no start, power loss, stall and other issues on SAAB 9-3s. It is an easy fix after you actually find it.
What is the Check Engine Light code on a Saab?