What are the codes on a 2007 International 4300 DT466?
HAVE CODES SID 254 I HAVE A 2007 INTERNATIONAL 4300 DT466. HAVE CODES SID 254 FMI 6 AND 221 FMI 4. IHAVE TESTED ALL THE WIRING FROM … read more
What are the codes for the International 4300?
2006 International 4300 DT466. I have codes 254 (controller 1 fault) fault mode id 8 and 6. Also code 164 (egr pos DT466..I have codes 254 (controller 1 fault) fault mode..pos… Auto Mechanics 1&2/diesel… I have a 05 international 4300, DT 466, started up this morning then it just died.
What’s the code for a DT 466E diesel truck?
We got couple of 05 International truck that has VGT problem. Code 152 (BAP signal out of range low). 354 (VGT control under duty cycle) and Body Controller – Remote Engine Speed Control #1 – Analog input #2 shorted to ground. Already replace BAP sensor, MAP sensor and VGT turbo.
What are the trouble codes for International trucks?
International Trucks Diagnostics Trouble Codes (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar
What’s the code for the FMI 6 injector?
06 international 4300 dt466 shuts off while driving restarts after a minute or so. Several codes and seems worse when driven on wet roads. Codes are Sid1 fmi5 and so on for all 6 injectors Sid34 fmi4 … read more
Where to find DT 466E trouble code list?
You can go to this site: https://evalue.internationaldelivers.com/service/bodybuilder/general/engine/eges270_FC.xml and click on the actual code (DTC) to access some decent diagnosis pages! Or scroll down for a quick reference. One word of *CAUTION*
What is fault code 525 FMI 6 injector dirver?
I have a truck with fault codes 525 fmi 6 Injector Dirver Circuit Fault *m* and 534 fmi 4 IDM- Relay Voltage Low. It doesnt show symptoms of a fault but it has the engine light on. It turns on and runs fine. I have checked the voltage to the IDM relay and its getting 12.4.
Where can I find the International Diagnostic Code?
International 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600 fault code list (PDF) – download The ability to display diagnostic trouble codes (DTC) is an optional feature. Codes may be displayed on either the gauge cluster or an optional vehicle information display (VID).
What are the engine codes for an international 4300?
Scanner says 8 engine codes. They are: FMI=4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. FMI=3 VOLTAGE ABOVE NORMAL OR SHORTED TO HIGH SOURCE. SPN175 ENGINE OIL TEMP. SPN 102 BOOST PRESSURE.
What makes a 2003 International 4300 sputter and Miss?
I have a 2003 International 4300 with a DT466. I just had all the O-rings on the injectors replaced along with the wiring harness that goes to the injectors. Now once the truck gets up to running temp it starts to sputter/miss. Truck runs GREAT cold but once warm gets worse.
What’s the difference between a DT466 and a VT365?
The VT365s VGTurbo depends on engine oil pressure to move its vanes so there is no key on, key off movement like in a DT466. The VT365 retains nearly one gallon of oil in its system that never drains out during an oil change, the percentage of retained versus drained oil is much higher than in a DT.
When do I need to replace DTC 353?
Depending on the part number, you may want to replace it rather than clean it. DTC 353 is set when the ECM overcompensates by increasing duty cycle to the VGT to achieve desired boost/back pressure. Do “Performance Diagnostics” .