What are symptoms of SPN 164 FMI 1?
SPN 164 FMI 1 (DTC 2335) ICP Unable to Build During Engine Cranking SPN 164 FMI 17 (DTC 3374)ICP Unable to build during test SPN 164 FMI 18 ICP below desired level SPN 164 FMI 13 ICP adaptation in-range fault SPN 8492 FMI 1 (DTC 3334)ICP Below desired SPN 1443 FMI 2 (DTC 2242) ICP adaptation in-range fault Observations or Concerns:
What does SPN stand for on a body controller?
DEFINITIONS •“SPN” represents the Suspect Parameter Number. This number identifies the item for which diagnostics are being reported. •“FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. 2 BODY CONTROLLER DIAGNOSTIC TROUBLE CODES (S08327)
What does FMI stand for in failure mode?
•“FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. 2 BODY CONTROLLER DIAGNOSTIC TROUBLE CODES (S08327) FAILURE MODE INDICATORS (FMI) DEFINITIONS
What is the SPN code for a FMI PID?
SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition 132 14 PID 322 1635 HC-Doser Fuel Pressure Not Plausible 132 1 PID 322 1213 Air Mass Flow Too Low
What is the engine coolant sensor code in FMI?
110 2 PID 110 1212 Engine Coolant Sensor (OUT), General Temp. Plausibility Error SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition
What is the Suspect Parameter Number ( SPN )?
The Suspect Parameter Number (SPN) is diagnostic fault code terminology found on some Caterpillar ® products using a J1939 CAN data link.
What does SPN stand for on a diagnostic code?
Previously active diagnostic trouble codes can only be cleared by a service tool, such as Diamond Logic® Builder (DLB). Some previously active codes may not be cleared by this method. “SPN” represents the Suspect Parameter Number. This number identif es the item for which diagnostics are being reported. FMI” is the Failure Mode Indicator.
What are the SPN numbers on a caterpillar?
Only the SPN numbers that are intended to be used on Caterpillar ® products are listed. Source Address of Controlling Device for Transmission Control Programming Error, Device Timed Out While Entering the Programming Mode
FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. Active” or “Previously Active” will be displayed to identify whether a fault is currently active or if the fault was previously active.
What are the fault codes for International trucks?
International Trucks Fault Codes List (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar. See also: International Trucks Service Repair Manuals PDF
What does FMI stand for in truck diagnostics?
FMI” is the Failure Mode Indicator. This number represents the type of failure detected. Refer to Failure Mode Indicators (FMI) below for more information. Active” or “Previously Active” will be displayed to identify whether a fault is currently active or if the fault was previously active. OC” is the Occurrence Count.