Is the rear door lock on my Jeep working?
My drivers side rear door will not lock / unlock with the keyfob, or the inside switches. It will work every now and then, but for the most part it doesn’t we have to unlock it from inside manually, and make sure it’s locked when leaving the jeep.
What’s the problem with my 1998 Jeep Cherokee?
1998 jeep Cherokee classic has door locking/unlocking problem. sometimes they work and sometimes they don’t. passenger door lock makes a ticking noise when I push the door lock on drivers door. nothing will lock or unlock electronically. any help on how to fix would be very helpful. oldman44oldjeep98, May 1, 2018.
Where can I get a new Jeep Grand Cherokee door?
Right today, you have a great opportunity to come to CARiD.com where you will be able to find a wide selection of the Jeep Grand Cherokee Doors produced by the most well-known manufacturers all over the world, among them you can find Replace and Goodmark. These brands offer only high quality products which your Grand Cherokee will definitely like.
Why is my passenger door lock not working?
If the passenger door button doesn’t work you will have to dig deeper and figure out where the problem is like 2oldjeeps says. The switch is the most common problem though. The door lock circuit is actually in the passenger door. I have an issue with my 00 XJ where they will work only occasionally and I can hear one of the relays clicking.
Why does my Jeep not unlock the passenger side door?
The power lock motor operates in 2 directions, by reversing the current. So if the motor works in one direction, the motor itself is ok. So maybe it is some wiring problem to the unlock side. The passenger side doors, the LH aft door and the liftgate are all controlled from the Passenger Door Module.
What kind of door lock does a Jeep Cherokee have?
Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37″ Toyo MTs. I will assume you have a 4 door Cherokee.
1998 jeep Cherokee classic has door locking/unlocking problem. sometimes they work and sometimes they don’t. passenger door lock makes a ticking noise when I push the door lock on drivers door. nothing will lock or unlock electronically. any help on how to fix would be very helpful. oldman44oldjeep98, May 1, 2018.
Where is the liftgate on a Jeep Wrangler?
The passenger side doors, the LH aft door and the liftgate are all controlled from the Passenger Door Module. I would start by looking into the fwd passenger door boot to see if there is any wire broken. This happened to my brothers ’00 WJ on the passenger side and I ended up replacing the lock actuator.
How to open a Jeep Grand Cherokee rear passenger window?
Remove two screws – one a Phillips head in the read door inside pull (armrest) and the other a Torx #15 just under the inside door release lever, Then pry the interior door panel off; release the two door latch rods, unplug the electrical wire to the window motor by first unlatching it.
Why are the passenger side doors not unlocking?
Just the passenger side doors won’t unlock. but they always lock The power lock motor operates in 2 directions, by reversing the current. So if the motor works in one direction, the motor itself is ok. So maybe it is some wiring problem to the unlock side.
The passenger side doors, the LH aft door and the liftgate are all controlled from the Passenger Door Module. I would start by looking into the fwd passenger door boot to see if there is any wire broken. This happened to my brothers ’00 WJ on the passenger side and I ended up replacing the lock actuator.
Remove two screws – one a Phillips head in the read door inside pull (armrest) and the other a Torx #15 just under the inside door release lever, Then pry the interior door panel off; release the two door latch rods, unplug the electrical wire to the window motor by first unlatching it.
Why is the liftgate on my Jeep not latching?
You will be able to then see where the striker fits up into the latch and then the little arm comes around the striker to latch the two together. If you get the latch unlatched it should latch. Good luck. It’s possible you closed the gate latch while you were wiping down the gate painted areas.
What to do if your rear door lock is not working?
It will work every now and then, but for the most part it doesn’t we have to unlock it from inside manually, and make sure it’s locked when leaving the jeep. pull the door panel off (super easy) and see if the actuator is loose or come off the door lock rod. very easy fix
Do you need to replace power Door Latch actuator?
If you don’t see the voltage toggle, work backwards to the switch to isolate the problem. The actual procedure depends on the year, make and model of your vehicle. Late model vehicles have the actuator built into the door latch assembly, forcing you to replace the entire latch.
How to turn off automatic door locks on a Jeep Wrangler?
The Wrangler is not equipped with Jeep’s EVIC (Electronic Vehicle Information Control) system, so the process is different. Insert your key into the ignition (do not turn) and close all the doors (leave them unlocked). Turn the key from “Lock” to “On” (without cranking) four times. End with the key in the “Lock” position.
How does the automatic lock work on a Jeep Cherokee?
This feature automatically locks your Jeep’s doors when the gearshift moves from “Park” to “Drive.” When the gearshift is returned to “Park,” the doors automatically unlock. This setting is customizable.
Why is the lift gate on my Jeep Cherokee not working?
Liftgate often will not close with the button. Have to manually close it against resistance of the hydraulics. Was told not to close it this way at purchase. Got recall card on the liftgate software, but the parts are not in yet. Too bad since the car is so often at the dealer for other %$#@& issues.
How do you turn off EVIC on Jeep Wrangler?
The Wrangler is not equipped with Jeep’s EVIC (Electronic Vehicle Information Control) system, so the process is different. Insert your key into the ignition (do not turn) and close all the doors (leave them unlocked). Turn the key from “Lock” to “On” (without cranking) four times.