How to troubleshoot an ICM error code on a Harley?
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release the odometer reset button.
What to do if your bike has an error code?
Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module. 10 – Turn Ignition switch to OFF.
What does the Code 02 mean on a Harley Davidson?
If it were a current code, the light would remain lit while running. Above codes can also be set if 02 sensor fails. CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.
How do you close the Diagnostic Code on a Harley Davidson?
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes.
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release the odometer reset button.
Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module. 10 – Turn Ignition switch to OFF.
How to get the trouble codes on a Harley Davidson?
The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.
Where is the BCM switch on a Harley Davidson?
BCM not configured properly. This DTCshould only apply to Police models. To enter diagnostic mode, press and hold the trip odometer trigger switch located on the left handlebar controls, while turning the IGN ON. The trip odometer trigger switch is located in the left hand control module.
Why does my speedometer not work on my Fatboy?
I just bought a 04 Fatboy. The right turn signal don’t work, but the left works fine. The speedometer dose not work, when I turn the ignition on the needle wiggles a little, when I turn to Access the needle goes all the way around and points straight down.
How to check ECM code on fuel Moto?
Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.
Why does my ECM log an error code?
When an issue arises, the ECM will log an error code that lets you know the source of the problem. This can be advantageous since you can determine the exact cause of failure. It can also be inconvenient since you’ll need a mechanic with an expensive computer to read the error code.
How can I tell if my ECM is failing?
When an issue arises, the ECM will log an error code that lets you know the source of the problem. This can be advantageous since you can determine the exact cause of failure. It can also be inconvenient since you’ll need a mechanic with an expensive computer to read the error code. What Would Cause ECM Failure?
Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.