How to reset check engine light on Mercedes slk230?

I found on the wiki a method how to reset check engine light on your MErcedes SLK230, switch the key in ignition on position 2, turn steering wheel full left then full right and back to centre and warning lights will be reset. This works only after you changing the battery.

Where is the reset SRS light on a Mercedes Benz?

Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car.

Why does my SRS light keep going on?

Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Step 1 Install a new battery; Step 2 Reset SRS/ Airbag light. Instruction on How to Reset the SRS Light on a Mercedes Benz: 1.

How to read and reset SRS / airbag light?

Battery dying. How to read and reset SRS/ Airbag light? Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it.

Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car.

What does SRS stand for in Mercedes Benz?

In this video, we will show you how to use the iCarsoft i980 to reset the SRS on Mercedes-Benz cars manufactured after 1996. What does SRS light mean? SRS stands for Supplemental Restraint System.

When does the Check Engine light come on on a Mercedes?

It illuminates when something requires the attention of a mechanic, or to remind you of periodic service needs. The light is designed to come on when the vehicle passes certain mileage limits. You can reset the “check engine” light on your Mercedes within a few minutes.

How to reset service light indicator Mercedes SL 500?

Within 10 seconds, turn key in steering wheel lock to position 0. Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again. The present status for days or distance is displayed again. Continue to hold button until you hear a signal (approximately 10 seconds). Release button.

What do you do when check engine light is lit?

Press the lower left button on the left side of the steering wheel. There are four buttons on the left side of the steering wheel. After pushing the button, the display will reveal why the check engine light is lit. Usually it indicates that the car is due for service.

Why is my Check Engine light not working?

Reduced gas mileage and stalling can also indicate a MAF problem. A MAF for a late-model car typically costs between $120 and $150. An aftermarket alarm can wreak havoc on your car if it’s not installed properly. It can drain the battery, trigger the check engine light, or even prevent the vehicle from starting.

What are the symptoms of a failed crankshaft sensor?

Other symptoms of a failed crankshaft position sensor are poor acceleration, engine vibrations, poor throttle response, bad fuel economy, hesitation, engine stalls. The engine starts if you let it cool down. If you are stuck on a parking lot and the car will not start, let the car cool down at least 30 minutes and then try again.

How to change the crankshaft position on a Mercedes Benz?

Unplug the electrical connector from the CPS sensor. Squeeze the connector and pull it away from the CPS sensor. This opens in a new window. Remove bolt. Remove the crankshaft position sensor. You will have either an E8 or E10 bolt that holds the CPS sensor in place.

When did the Mercedes SLK 230 Kompressor come out?

Mercedes introduced a refreshed SLK in 2000. Apparently learning from their mistakes, they lowered the power of the SLK 200 Kompressor down to 161 hp. On the other hand, the SLK 230 Kompressor was given a new engine, and power was increased to 194 hp and an identical 207 lb-ft of torque. 0 to 60 time is down, however, by 0.1 seconds (7.3s).

What to look for in a Mercedes SLK 230?

An SLK 230 Kompressor is an easy find and won’t cost much upfront. Look for one that doesn’t have a cracked dashboard, preferably one that has been replaced – this seems to be a common problem for early 2000s Mercedes. Consumer Affairs suggests mixed feelings about the SLK’s reliability.

How to reset service light indicator Mercedes SLK 200 Kompressor?

Manual Reset Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds. Present status for days or distance is now displayed. Within 10 seconds, turn key in steering wheel lock to position 0. Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again.

Why does my SLK not start or crank over?

All the dash lights come on as normal no error codes showing everything in car works however when turn that key the last little bit for the starter nothing. this happend once before but 20 minutes latter it started and has been fine since however it was the same way before it sat for two weeks when it happened. checked all the fuses all fine.

Where to find DTC code on Mercedes SLK 230?

The dreaded Check Engine light (arrow) stays illuminated when the car’s computer registers a diagnostic trouble code (DTC). Disconnecting the battery doesn’t erase the code. The scan tool’s cable (or a Bluetooth module on wireless systems) plugs into the OBD-II diagnostic port (yellow arrow).

Where is the fault code on a Mercedes SLK?

Disconnecting the battery doesn’t erase the code. The scan tool’s cable (or a Bluetooth module on wireless systems) plugs into the OBD-II diagnostic port (yellow arrow). On the R170 SLK, the port is located on the under-dash panel, behind the hood-release lever (blue arrow).

When does the Check Engine light come on and go off?

The check engine light often comes on and goes off after a while. Any time I notice it whiles driving, I park and close the fuel tank well but the light doesn’t go off. Sometimes I restart the car but it still won’t go off. It goes off on it own and comes back after some time.

What causes check engine light on Mercedes Benz?

Fortunately Mercedes-Benz of Houston Greenway is here to help you figure out what might be wrong, and what your next steps should be. Below we have highlighted the most common causes of a check engine light. Loose Gas Cap: Your gas cap is loose, broken, or simply missing.

What to do if your check engine light is flashing?

Once you’ve noticed the check engine flashing, don’t worry. If it’s for gas cap failure, the fixing will take a mere few minutes. Turn off the engine vehicle. Open the gas cap door. The door is usually locked, you’ll find a push button to unlock it.

Why is the gas cap missing from my Check Engine light?

The cap is not in place or securely sited. The cap is completely disappeared or missing from the car. The cap cannot close properly due to grime and mud near the opening. The gas tank is out of shape due to an accident, putting extra pressure on the gas cap.

How to check your Mercedes Benz service engine?

If you are having trouble with a Mercedes Benz then go to mercedesmedic.com/ faultcodes/ to get an idea of what your problem is. If you want to do more research then use Search function on Mercedes Medic or any other search engine to get a better idea of the problem. On any search engine enter the manufacturer and the code you got from the scanner.

What does it mean when your check engine light stays off?

Once you fix the problem then you can use your scanner again to erase or reset the check engine light. If the problem has been fixed the Check engine light will stay off. If it comes back again that mean the problem has not been fixed or there is another problem.

How to get a Mercedes GLB test drive?

Caledon drivers considering a Mercedes-Benz GLB, read on for a comprehensive breakdown of Mercedes-Benz GLB price and Mercedes-Benz GLB 35 AMG price by trim level. Then fill out a pre-approval and reach out to Mercedes-Benz Brampton to schedule for a test drive.

Why does my Bas light come on in my Mercedes Benz?

To reset the lights, start up your Mercedes-Benz and turn the steering wheel all the way to the right, then all the way to the left. Do this a couple of times. Turn off the engine. Restart. Brake Light Switch may cause BAS / ESP / ABS light to come on. It is the most common problem with Mercedes-Benz cars.

How can I repair my Mercedes SLK 230 overload protection relay?

A brass clip (green arrow) keeps the K40 in place. Pressing it outward sets the K40 free. Pull the plugs off the K40 and remove it from the car. A skinny flathead screwdriver can be used to pry the relay board out of the case. Check the relay side of the board for obvious problems: charred or loose connections, etc.

Why is my heat shield not working on my SLK 230?

A heat shield and a blower motor keep the electronics in the box cool. A non-functioning blower can be a root cause. With the ignition switched on, this fan is audible, and airflow should be felt with the control module’s cover removed.

Where is the K40 relay on a SLK 230?

If those lead to dead-ends, the K40 is worth scrutinizing. The K40 relay is located in the control module box, under the hood. In left-hand-drive R170 SLKs, this box is near the exhaust manifold. A heat shield and a blower motor keep the electronics in the box cool.

What’s the trouble code on a Mercedes SLK?

Many current-generation scan tools define the trouble codes. However, older scanners and really cheap ones might reveal the code but require you to find its definition in a service manual or via a web search. Codes generally fall in one of three categories: P (powertrain), C (chassis), or B (body).

Where are the fuses on a Mercedes Benz SLK?

Fuse box diagram (fuse layout), location, and assignment of fuses Mercedes-Benz SLK (R170) (SLK 200, SLK 230, SLK 320 and SLK 32 AMG) (1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004). The fuses in your vehicle serve to close down faulty circuits. If a fuse blows, all the components on the circuit and their functions stop operating.

Where is the USB port on the R170 SLK?

On the R170 SLK, the port is located on the under-dash panel, behind the hood-release lever (blue arrow). The port is protected by a plastic cover, which pivots away so that the cable can be plugged in.

When did Mercedes Benz stop making the SLK?

Production of the SLK/SLC was discontinued in February 2019. The R170 Mercedes SLK was the first generation compact roadster produced by Mercedes-Benz, from 1996 to 2004.

Where can I buy a 1998 Mercedes SLK Class?

Description: Used 1998 Mercedes-Benz SLK-Class SLK230 Kompressor. EXCLUSIVE MARKET PRICING NO HAGGLE WITH NO PRESSURE AND CLEAN TITLE @ 10790 South State St Sandy UT 84070. Bring this ad with you ! !

When does the Mercedes Benz SLC Class end?

The model range was also renamed to SLC-Class to conform to the new Mercedes nomenclature, and introduced new engines and a revised design. In 2020, Mercedes-Benz released a Final Edition to commemorate the end of the car’s production run. The following are the sales figures for the SLK-Class since 2001:

When did the Audi R172 SLK come out?

The front-end design of the car was inspired by the noses found in Formula One cars. It was facelifted in 2008 and featured new engines and minor exterior design changes. The R172 SLK was released in 2011.

Why is the engine management light on on my SLK?

The engine management light on my slk has been on for some time now. When it first came on I had a diagnostic test done and told my air mass meter was bust. So I had it replaced and the car was running brilliantly.

Why is the check engien light on on my Mercedes?

They measure the unburned oxygen. If your Check Engien Light is on because of O2 sensor you may be getting poor fuel economy as well. The input values from the O2 sensor are used to adjust the fuel delivered to the engine. You can get O2 sensors at a fraction of dealer prices on Amazon, that will fit Mercedes Benz. Check this one here for example.

Where is the O2 sensor on a SLK?

Stab in the dark, two rubber pipes under the inlet manifold into cylinder head and down into one valve have perished. And or the O2 sensor is on its way out. Click to expand… Of course, if its P203B that relates to the throttle (so do check what jibcl500 is suggesting since its all related).

When did the Mercedes Benz SLK Class come out?

In this article, we consider the first-generation Mercedes-Benz SLK-Class (R170), produced from 1996 to 2004.

Where is the fuse box on a Mercedes Benz SLK?

The fuse box is located on the side of the instrument panel, behind the cover (on the left in the LHD, on the right in the RHD)

What to do if your check engine light is on?

Thankfully, Mercedes-Benz Brampton of Brampton is here to take care of your vehicle. Our trained technicians have access to all of the best Mercedes-Benz parts to get your vehicle fixed quickly and efficiently.

What to do when your check engine light comes on?

No matter the situation, when the check engine light comes on in your Mercedes-Benz, we always suggest stopping by our service center so one of our knowledgeable technicians can properly diagnose and repair your vehicle. Our service technicians have the most up-to-date diagnostic equipment that can quickly read Mercedes-Benz OBD codes.

What should I do if my radiator fan is not working?

A blown fuse is no big deal, and changing one does not cost a lot of money. If your car’s radiator fan is non-functional, check your car’s user manual and locate the fuse for the radiator fan controller or the fan. The fan itself often uses a big fuse of around 50A, while there might also be a separate small fuse to the fan control module.

Why does my radiator fan run full speed when I start the car?

Immediately upon starting the car, the radiator fan begins to run full speed, even though the car is stone cold. The AC is OFF. The radiator and condenser are BRAND NEW. This problem existed before and after the radiator was replaced. The fan continues to run at its maxiumum speed, regardless of the engine temperature.

What are the symptoms of a bad cooling fan relay?

1. Engine running hot One of the first symptoms commonly associated with a bad or failing cooling fan relay is an engine that runs hot or overheats. If you notice that your engine is running at higher temperatures than normal, that may be a sign that the relay is not functioning properly.

Why is my Mercedes SLK Class R170 not starting?

Crankshaft sensor fault code or an engine that won’t start. We’ll show you how to replace your crank sensor in this tech article. Over time the tensioner can fail to maintain the proper tension and the belt will start to slip. Noticed that the area around your valve cover is filthy with oil? There is a very good chance the gaskets are going bad.

How can I tell if my radiator fan is working?

When a radiator fan works it usually makes a whirring sound that is easily noticeable. However, the radiator fan does not always start spinning on ignition. The ECU signals the radiator fan to work at the precise time. So, do not worry if the fan doesn’t immediately start working. Visually check the fan if you don’t hear its noise. 1. Broken Fuse

Can a bad crank sensor cause a check engine light?

First you have to remove the air intake duct. A bad cam sensor can cause reduced engine power and a check engine light. Here’s how to change it out in under 10 minutes. Crankshaft sensor fault code or an engine that won’t start. We’ll show you how to replace your crank sensor in this tech article.

What do the warning lights on the Mercedes slkclass mean?

It’s important to know what the dashboard Mercedes-Benz SLKClass warning lights actually mean, though, not least because they can pre-empt a car breakdown or full-on failure, potentially saving you from an expensive repair bill and meaning you stay safer on the road.

What are the warning lights on a Mercedes Benz?

The following are warning lights and indicators found in vehicles built by Mercedes Benz. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are over 40 of them so be patient!

Where are the Phillips screws on a Mercedes SLK 230?

Three Phillips screws (arrows) retain the headliner’s front edge to the roof. Each side rail has three star screws (arrows). The rear-most screws are above the top’s cables. Once all nine screws are removed, the headliner can be lifted out.

How is the Mercedes SLK 230 headliner held in place?

Regardless of the motivation for removal, the headliner is held in place by nine Phillips screws: three on the leading edge and three on each side. They’re all accessible by opening the top halfway. Once the top is partially retracted, remember to turn the key to its OFF position to depressurize the hydraulic system.

What kind of car is the Mercedes SLK 230?

Mercedes-Benz SLK 230 New Listing $5,999 Oak Auto NC Used 1998 Mercedes-Benz SLK 230 $6,880 Coda Motors LLC Used 1999 Mercedes-Benz SLK 230 New Listing $6,900 Fast Track Auto Mall Used 1999 Mercedes-Benz SLK 230 $8,449 Dream Wheels Used 1998 Mercedes-Benz SLK 230 $8,450 Timeless Motorcars Used 1999 Mercedes-Benz SLK 230 $8,490

Where is the fill hole on a Mercedes SLK 230?

If the fluid is low, the fill hole is on top of the hydraulic pump. The plug is easier to access by removing the metal cover, which is secured by four bolts having T30 Torx heads (arrows). The filler hole (arrow) is on top of the pump, on the right-rear fender side.

How many hydraulic cylinders are in a SLK 230?

Five hydraulic cylinders, nine limit switches, a control switch, four window motors, a pump, two solenoids, a relay, cables/pulleys, and a control module all have to work in sync for the top to operate properly. If one link in the chain breaks down, the top either won’t work or it stops mid-retraction.

Why is my hydraulic pump not working on my Mercedes SLK?

If the battery reads at least 11.4 volts with the engine off and its cables are clean and clamped snugly on its terminals, then focus on the top’s switch. If nothing happens when the switch is pulled and the switch doesn’t illuminate, then it or its connections could be bad.

How many BHP does a Mercedes SLK have?

Unlike the Boxster though, the Mercedes four-cylinder engine doesn’t have any Achilles’ Heels in the engine bay, but with the Eaton blower on the M111 engine it’s good for a handy 193 bhp. The SLK may lack an exotic soundtrack but there’s no doubt as to its performance.

When did the Mercedes SLK 230 come out?

Launched in 1996 and immediately creating a two-year waiting list, the Mercedes SLK is very much a low-key and under-appreciated modern classic today yet it kick-started a whole new rtrend for the industry. It also represented a big departure for Mercedes itself which at the time was suffering from a rather stuffy image.

What causes a MAF fault on a Mercedes Benz?

In extreme cases, hot exhaust can cause the catalytic converter’s internal honeycomb material to unbond from the converter’s housing. When this happens, the converter is toast. The most common Check Engine Diagnostic Trouble Code (DTC) caused by a MAF fault is P0056.

How to fix a check engine light on a Mercedes Benz?

Hopefully you don’t have any serious problems with your car. If it is a Mercedes Benz you can use the search function on Mercedes Medic to see if there is an article that will show you how to fix what is wrong. Once you fix the problem then you can use your scanner again to erase or reset the check engine light.

Is the Check Engine light on in my Mercedes?

Has the check engine light turned on in your Mercedes-Benz C-Class, E-Class, GLA, GLC, GLE, ML, or SL? It can be alarming seeing an engine warning appear on your dashboard, especially if you’ve never seen it before.

Is the Mercedes SLK 230 still in production?

See reviews below to learn more or submit your own review. The SLK 230 is a luxury coupe that is currently discontinued. Read more Mercedes-Benz reviews to learn about other models. I paid 70,000 for a beautiful design copper color Mercedes SLK 230 in the year 2000. After 2-3 years the dashboard started cracking and falling apart.

How long does it take to change an oil in a Mercedes SLK 230?

If you have changed the oil and filter the motor should take 6 quarts. Begin by safely jacking up and support your car. With the car safely off the ground you will need to remove the engine tray. There are four 8mm screws (red arrows) holding the tray on.

When did the Mercedes SLK R170 come out?

I live in the Rockies and the mountain folk aversion to rwd vehicles is near legendary so my search took me well out of my area. The R170 version of the SLK was only made from 1998 through 2004, averaging about 10,000 US versions each year. I’ve discovered that only about 10 percent of these have manual transmissions.

How many miles does a 2003 Mercedes SLK 230 get?

Mileage: 78,440 miles Body Type: Convertible Color: Gray Engine: 4 Cyl 2.3 L Description: Used 2003 Mercedes-Benz SLK 230 with RWD, Supercharger, Keyless Entry, Fog Lights, Leather Seats, Bucket Seats, Wind Deflector, Alloy Wheels, Hard Top, Bose Sound System, and Heated Mirrors 2003 Mercedes-Benz SLK 230 13 Photos

In this article, we consider the first-generation Mercedes-Benz SLK-Class (R170), produced from 1996 to 2004.

What does the Check Engine light on a Mercedes mean?

There are four buttons on the left side of the steering wheel. After pushing the button, the display will reveal why the check engine light is lit. Usually it indicates that the car is due for service. Push the lower left button on the steering wheel again and the vehicle mileage will show on the display.

What to do if your Mercedes Benz check engine light comes on?

Your Mercedes-Benz expert will be able pinpoint the problem for you by connecting your Mercedes-Benz to a diagnostic scan tool. This tool will provide trouble codes stored in your electronic control system, and reveal why the check engine light came on.

Navigation