How to reset an anti theft system for a Mercury Mountaineer?

At that time, the little red light should return to blinking at the slower, passive rate. If, once again, the Mountaineer fails to start, continue to Step 3. Raise the hood and use the battery terminal wrench, or a standard box wrench, to remove the negative battery cable. Wait 15 minutes before reconnecting the cable, then repeat Step 1.

What to do if your Mercury Mountaineer won’t start?

If your Mountaineer still will not start, and the flashing red light begins blinking rapidly when you attempt to start it, something is obviously malfunctioning. Either have the key reprogrammed or have more extensive troubleshooting and repairs done to the P.A.T.S. system by a certified technician.

Is there an anti theft system on a Mercury?

Contrary to popular belief, Ford, Lincoln and Mercury vehicles do not come equipped from the factory with a standard alarm system. Instead, the Ford Motor Company equips its vehicles with a passive anti-theft system, known as P.A.T.S.

What to do if anti theft light goes off?

Once ten minutes has passed come back and check the anti-theft light. If it has gone off, then turn the key back to the off position and remove the key. Wait for a couple of minutes to make sure that the system reset is finished. Then put the key back in and try to start the car.

How do you reset the P.A.T.s on a Mercury Mountaineer?

Either way, you must reset it before you can operate the Mountaineer. Unlock the door and insert the programmed key into the ignition and start the Mountaineer. In most cases this will reset the P.A.T.S. system and allow you to drive away. In the event it does not, move on to Step 2.

When do I need to Reset my passive anti theft system?

Passive Anti-Theft Systems (PATS), also called Ford Securilock, is a vehicle security feature introduced on 1996 and later Ford vehicles. When replacing the Powertrain Control Module (PCM) on a PATS-equipped vehicle, a parameter reset or relearn procedure must be performed after the PCM is installed.

How to solve the anti theft system car wont start?

It is another way to solve the problem of anti theft system car wont start. Disconnect the positive terminal of the battery for a minute or two. Reconnect it and make sure that both the anode and cathode terminals are tightly attached. It will reset the computer system and your car is likely to kick off.

What to do if your anti theft light won’t turn on?

If this is some other type of light then disconnect your battery (negative first then positive) for 30 minutes and reconnect in reverse order (positive then negative). This should reset the computer. You will loose presets in your radio.

How do you reset P.A.T.s on a mountaineer?

Unlock the door and insert the programmed key into the ignition and start the Mountaineer. In most cases this will reset the P.A.T.S. system and allow you to drive away. In the event it does not, move on to Step 2.

Do you need to reset the alarm on a mountaineer?

Many insurance companies offer discounts on cars with alarm systems. However, it’s not a perfect system. You may experience a false alarm, in which case you will need to reset your Mountaineer’s alarm. You must use the original key that came with the vehicle to deactivate and reset the alarm.

What does the Mercury Mountaineer car alarm do?

The alarm on your Mercury Mountaineer acts as a theft deterrent. This anti-theft device may do more than just protect your vehicle from being stolen. Many insurance companies offer discounts on cars with alarm systems.

Can you use keyless entry on a Mercury Mountaineer?

Using the Keyless Entry feature for a Ford Explorer or Mercury Mountaineer can be a convenient feature. However, if you forget your personal code it can be a challenge to get into your car without damaging it. There are a few cheap and easy ways to retrieve the 5-digit factory code without any tools or automotive expertise.

What kind of problem does Mercury Mountaineer have?

Mercury Mountaineer 2004, AWD, V8. Bought this used with 40k miles on it. The engine dies (dead) when using the cruise control. control, several minutes pass by and suddenly the engine is dead. Most of the warning lights in the instrument cluster come on.

When does a Mercury Mountaineer start stall idle?

Amazing I have a 2002 Mountaineer V8 with the same issue, started 3 yrs ago. Mercury/Ford claims they have never seen this before. Mainly stalls when car comes to a stop sign in the mornings, never had a high speed stall. I have replaced fuel filter and air control valve.

What to do if your Mercury Mountaineer starts stall idle?

I recommend a BG Induction service if you have never had this done and your vehilce is over 65,000 miles. Mercury Mountaineer 2004, AWD, V8. Bought this used with 40k miles on it. The engine dies (dead) when using the cruise control. control, several minutes pass by and suddenly the engine is dead.

When did the dpfe sensor go away on the Mercury Mountaineer?

We took the Mountaineer to another dealer and they replaced the DPFE sensor in July of 07. Until then to now the problem went away.

Why is my p.a.t.s.engaged on my Mercury Mountaineer?

If the P.A.T.S. is engaged on your Mercury Mountaineer, chances are someone either tried to steal your vehicle or tried to start it with a key that was not programmed to the P.A.T.S. transponder in your vehicle’s dash. Either way, you must reset it before you can operate the Mountaineer.

Where does the wire go on a Mercury solenoid?

There are four terminals on the solenoid–two large-diameter posts and two small-diameter posts. A large wire (4-gauge or larger) goes from the B+ post on the solenoid and the other large post has the large diameter wire going directly to the starter. When the solenoid is not energized, there is an open circuit between these two large wires.

What should I do if my car alarm wont turn on?

If it’s no longer blinking, turn the key back to the Off position and allow it to set for a minute or two. This gives the system time to reset or you won’t be able to start your car. Step 4: Start the engine. Attempt to start your engine. If it still won’t start, check to make sure the battery hasn’t been drained. Step 5: Repeat the process.

What to do if your car anti theft light is not blinking?

Leave the key in position for about 10 – 15 minutes. Step 3: Check the anti-theft light again. If it’s no longer blinking, turn the key back to the Off position and allow it to set for a minute or two. This gives the system time to reset or you won’t be able to start your car. Step 4: Start the engine. Attempt to start your engine.

When did the Mercury Mountaineer fuse box come out?

In this article, we consider the second-generation Mercury Mountaineer, produced from 2002 to 2005. Here you will find fuse box diagrams of Mercury Mountaineer 2002, 2003, 2004 and 2005, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

Where are the relays on a Mercury Mountaineer?

These relays are located on the reverse side of the passenger compartment fuse panel. To access the relays you must remove the passenger compartment fuse panel. The Power distribution box is located in the engine compartment (on the driver’s side), under the cover.

What is the keyless code on a Mercury Mountaineer?

Many Ford Explorers and Mercury Mountaineers were manufactured with an option known as the Ford keyless entry keypad. Some models refer to it as SecuriCode as well.

When did the Mercury Mountaineer stop being made?

The Mountaineer was never sold in Canada. As part of the discontinuation of the Mercury brand, production of the Mountaineer ended in late 2010. In 1990, General Motors introduced the Oldsmobile Bravada sport-utility vehicle, derived from the four-door Chevrolet S-10 Blazer.

What kind of drive did the Mercury Mountaineer have?

Like the Ford Explorer, the V8 engine was mated to either rear-wheel drive or full time all-wheel drive (viscous coupling center differential); part-time four-wheel drive was unavailable with the V8 engine. The V6 Mountaineer or Explorer were offered either as rear-wheel drive or ControlTrac with “Auto”, “High” and “Low” modes.

What to do if your car anti theft system is not working?

Step 1: Check your key fob battery. A car’s anti-theft system may activate if your key fob battery is dead and hasn’t disabled the system. Make sure the battery is installed correctly in your key fob. If the battery is correctly installed, replace it with a fresh battery and try again.

What happens if I dont turn on my anti theft system?

The key you are using may not have the chip required to start your car. If the anti-theft system has locked up your engine, you won’t be able to start it. You’ll have to disable it with these steps. Step 1: Check for the anti-theft light. It’s located on your dash and will have a blue or red light. Step 2: Turn the ignition to the “on” position.

When to use the p1260 Ford theft code?

P1260 Ford Description. The P1260 code can be set if the Passive Anti-Theft System (PATS) has determined a theft condition existed and the engine is disabled or an engine start was attempted using a non-PATS key. This Diagnostic Trouble Code (DTC) is a good indicator to check the PATS for DTCs.

Where is the keypad code on a Mercury Mountaineer?

To enter your keyless keypad code: On Ford Explorers and Mercury Mountaineers from 2006 until the model year 2010, the default five-digit keypad code is printed on the smart junction box (SJB) under the driver’s side of the dash. Step 1: Look at your under dash.

Is the Mercury Mountaineer 4.6L V8 overheating?

The Mercury Mountaineer 4.6L V8 model is known for engine overheating, even with normal use, and a coolant leak from the front of the manifold. This will often trigger the check engine light and low engine coolant warning light.

Which is the best Mercury Mountaineer to buy?

Our 2004 mountaineer was the best car we ever owned. The 2008 mountaineer is a close second. Spark plugs are the only major problem. Several broke when trying to remove for first time. Since then 7th and 8th cylinders have failed twice. Pretty loud exhaust leak, but seals up after the engine gets warm.

What’s the value of a 2007 Mercury Mountaineer?

Kelley Blue Book expects the Mountaineer to hold only average resale values over a five-year period. All-wheel-drive models with the V8 are expected to retain a slightly higher resale than the V6, but all versions fall far below the values held by competitors from Toyota, Honda and Nissan.

What are the safety features of a Mercury Mountaineer?

The optional Reverse Sensing System alerts you to objects behind the vehicle that are out of the range of the rearview mirror. The Mountaineer’s standard Safety Canopy airbag system protects passengers in the event of a rollover or side collision.

Is the Mercury Mountaineer a 4 wheel drive car?

Best of all, the Mountaineer retains all the beneficial features of the Explorer, including seven-passenger seating, a rugged body-on-frame architecture and four-wheel-drive capability. Toss in the standard Safety Canopy side-curtain airbags and a long list of luxury and entertainment features, and the Mountaineer looks to be quite a bargain.

What should I do if my anti theft system is not working?

In the event it does not, move on to Step 2. If the system is in active mode, the little red flashing light on the dash will be blinking rapidly, at roughly twice the speed of its normal, passive mode blinking rate. Verify that you have the correct key or try another known good key, and wait for 15 minutes to pass before repeating Step 1.

Why is my anti theft light blinking fast?

First, if your theft light is blinking fast it means either you or someone else tried to get into the vehicle without a key or….some tried to use a key that did not have a chip in it. NEVER, EVER USE A KEY THAT DOES NOT HAVE THE CHIP TO START YOUR CAR…DONT DO IT. It will trigger the PATS Anti theft system.

Why is the anti theft light blinking ON MY 2001 Ford Explorer?

Says there is no re-programming involved because it simply reads the chip and sends the info to the system. The last time my 2001 Explorer failed to read the chip I just bumped the steering wheel a couple times to send vibrations through the column. It worked.

Why is my anti theft light still on on my explorer?

This happens if you put the wrong key in accidentally. Get into the Explorer and insert the known correct key into the ignition and turn it. If you use the wrong key, such as one that was cut to open the doors, the system will remain armed. If the car then starts, then you have disarmed the anti theft system.

Why is the Check Engine light on on my mountaineer?

I have had my Mountaineer in the shop twice due to the check engine light being on as well as the Check fuel Cap. The dealer said that I was getting the messages in error and reset the computer. This works for a few weeks then the light comes back on. Is there anyway to fix the error message?

Why are the fog lights not working on my Mercury Mountaineer?

Has anyone else seen this electrical problem in any of their vehicles before? I have a 2000 Mercury Mountaineer. When you turn the head lights on and have the fog lights on, the fog lights do not work at all. Also, the turn signals will not work with the fog lights on and the headlights on.

Who are the writers of the song Buttons?

#ThePussycatDolls#Buttons#Vevo#Pop Category Music Song Buttons (Album Version) Artist The Pussycat Dolls Writers Nicole Scherzinger, Jamal Jones, Garrett Hamler, Jason Perry Licensed to YouTube by

How to disable the alarm on a mountaineer?

Turn your key to the unlock position. Your alarm is now disabled. If your key fob works, you can also press the unlock or alarm-disable button on the fob. Start the Mountaineer’s engine and allow the vehicle to run for at least 10 minutes. This will allow the alarm to relearn the default settings.

Where is the ignition key on a mountaineer?

Insert the ignition/door key in the door lock on the driver’s- side door of your Mountaineer. Turn the key to the lock position. Turn your key to the unlock position. Turn your key to the lock position. Turn your key to the unlock position. Your alarm is now disabled.

What to do if your ignition key won’t turn?

This feature is not available right now. Please try again later. Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Loading…

Navigation