How to replace the serpentine belt in a Jeep Grand Cherokee?

Rotate the belt tensioner pulley, using the wrench, to and relieve tension on the belt. Slip off the old belt and slowly release the tensioner pulley. Use your belt routing diagram to put the new belt onto all of the pulleys. Pay close attention to the water pump pulley, as incorrect routing can cause the water pump to run backwards and overheat.

How do you remove a serpentine belt from a car?

Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.

How often should I replace my serpentine belt?

The manufacturer recommends checking the serpentine belt every 7,500 miles or 6 months for potential replacement due to normal wear. Find the belt tensioner pulley. The tensioner pulley is generally between the crankshaft and a component toward the top of the hood area. Check the belt routing so you know how to replace the belt.

How is the tension set on a serpentine belt?

Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.

How do you change power steering belt tension?

On these models, change the tension on the belt by loosening the two power steering bolts on the side of the power steering pump, then turn the adjustment bolt below the pump counter-clockwise to release tension on the belt. Follow the above steps for replacement using this alternate system.

How do you change the belt on a water pump?

Use your belt routing diagram to put the new belt onto all of the pulleys. Pay close attention to the water pump pulley, as incorrect routing can cause the water pump to run backwards and overheat. Make sure the belt is correctly routed and seated on all pulleys.

What’s the best way to replace a serpentine belt?

Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it.

What happens if a serpentine belt goes bad?

The serpentine belt in most modern vehicles transfers power from the crank pulley to the various accessories mounted on the engine. A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function.

Where do I find the serpentine belt routing diagram?

Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.

How do you change the belt tension on a Jeep Grand Cherokee?

For some older 6-cylinder models, the belt tension system is different. On these models, change the tension on the belt by loosening the two power steering bolts on the side of the power steering pump, then turn the adjustment bolt below the pump counter-clockwise to release tension on the belt.

How is the serpentine belt in a Chev?

Pictures, diagrams of serpentine belt routing. 2.4L. Belt Diagram 3.4 DOHC Cam Engine Drive Belt Diag… 3.5L Engine Serpentine Belt in Chev… 4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro…

How do you tighten a serpentine belt on a car?

If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.

Where do I find the serpentine belt on my car?

To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.

What kind of pulley does a serpentine belt use?

Determine if there is a belt tensioner pulley. Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times.

Where to find belt routing diagram on Jeep?

Now, locate your “Belt Routing” diagram, which is a decal that should be affixed to the top of the radiator or on the sheet metal under the hood somewhere quite visible. After finding the routing decal, locate belt tensioner.

How to replace serpentine belt on Jeep 4.0L?

1 Serpentine Belt (I use Goodyear Gatorback P/N 4060882) First, open the hood, get out the shop light and 3/8″-drive breaker-bar/socket-wrench.

What should I do if my serpentine belt breaks?

A serpentine belt is an inexpensive way to make sure that you won’t get stranded from a broken, rotten, old serpentine belt. With age, your rubber serpentine belt will begin to crack and dry-rot, and could possibly break at the worst possible place. This belt is also known as the “accessory belt” or “fan belt”…

How often should I replace my belt on my Jeep?

On most vehicles that are driven regularly, belt replacement every 30,000 miles is almost TOO frequent. To find out how to check and see if your belt is needing replaced or not, check my belt inspection writeup.

How long does it take to replace serpentine belt?

Once on, make sure the belt is completely on and centered on each pulley very carefully. Then, start the engine. Let the engine idle for at least 60 seconds as you make sure the serpentine belt is working correctly. Replace any other parts or coverings you’ve removed before taking your vehicle for a spin.

How do you remove a serpentine water pump belt?

If it is a serpentine belt, remove the belt by using a breaker bar and turning the tensioner to relax the belt. If the vehicle has a v-belt, loosen the tensioner to relax the belt. Step 6: Remove the belt or belts from the pulleys. Step 7: Locate the tensioner to the belt.

What to do if your water pump belt breaks?

Step 1: Open the hood to the engine compartment. Grab a flashlight and visually check the water pump belt for any weather cracking or breaks. Step 2: Push on the belt to make sure that the tensioner is working correctly. For serpentine belts, the tensioner should move as the belt is being pushed on.

How to check the belts on a 2014 Jeep Cherokee?

We are still working to obtain content for your car, however the video above is believed to have similar characteristics as your car. The video above shows how to check the belts on your 2014 Jeep Cherokee – if it gives more than a half inch when pressed, is cracked, frayed or appears shiny, you should change it (or have it changed) immediately.

Is there a spring loaded belt tensioner on a Jeep Cherokee?

XJ Cherokee models do not have a spring loaded belt tensioner, but instead use manual belt adjustment at the power steering pump to adjust belt tension. For early XJ models, it is best to remove the airbox assembly for easier access to the power steering tensioner bolts (refer to article How to Make and Install Cold Air Intake for airbox removal).

How do you change the belt on a Jeep XJ?

Later XJ models have a simpler belt adjustment procedure requiring only the the idler pulley and belt adjusting bolt be loosened for removal. With a 15mm wrench, loosen the idler pulley “tensioner bolt,” but do not remove it. Next, loosen the adjuster bolt with a 15mm socket, ratchet and extension.

When to replace serpentine belt on 1990 Silverado?

Replacing the serpentine belt on your 1990 Silverado pickup will help prevent an accidental belt failure when you least expect it. The belt turns every accessory on the front of the engine, including the water pump and alternator. If the belt breaks, the truck will overheat and lose electrical power for the ignition system.

What do you call the serpentine belt on a car?

What is a Serpentine Belt? A serpentine belt, also called an accessory belt, is the main engine belt that you see when you open up the hood of your car. These belts are easily identifiable by their distinct ridges that run the length of the belt on one side. The ridges help maintain grip when turning the accessory pulleys.

How to tell if your serpentine belt needs to be replaced?

Look for signs of damage or wear on the belt. Once you have located the serpentine belt, inspect it visually for signs of damage. If the belt is frayed, coming apart, or has marks that indicate that it has been rubbing on something, it will need to be replaced.

When do you know you need to replace your belt tensioner?

If you notice that there is resistance, roughness, or noise every time you turn the pulley, then there’s a chance that the problem is in the pulley bearings. You might think of replacing only the pulley bearings in this case. Mechanics will tell you to replace the entire belt tensioner system.

Where is the tensioner on a Jeep Grand Cherokee?

The good news is, the tensioner is secured to the engine via the alternator mount. Taking the mount out is very easy. Making sure the engine is cold, remove the top radiator hose, then the alternator (2 bolts 15mm socket), then the alternator mount (4 screws, 14mm socket). The tensioner is attached to the front of the mount.

How to get a serpentine belt cross reference?

SERPENTINE BELT CROSS REFERENCE Customer Service: 800-95-BANDO | [email protected]| www.BandoUSA.com W O R L D C L A S Q U A L I T Y SI N CE 1 9 0 6 Metric 6 Number of Ribs Size of Rib Number of Ribs Length in 10th of an inch Millimeters x 0.03937 = inches Inches x 25.4 = millimeters Metric Pitch – Size of Ribs Number of Ribs

How often should a serpentine belt be replaced?

Water pump and cooling fan (for vehicles not equipped with an electric cooling fan) Power steering pump (to give you power-assisted steering if you have it) On most vehicles that are driven regularly, belt replacement every 30,000 miles is almost TOO frequent.

When to replace serpentine belt tensioner — Ricks free?

A good belt tensioner will dampen the power pulses so much that the tensioner pulley arm barely moves. As the dampener wears the pulses cause the belt to flutter and that can be seen on the pulley arm. A belt tensioner pulley arm should not move more than 1/32”.

Is the 5.7 commander serpentine belt easier to change?

I have found the 5.7 commander serpentine belt to be much easier to change than many other vehicles I have worked on. You should try changing a belt on a Saab 9-5 Turbo!!! Thanks for the info. I’m sure I’ll be doing it in a little while.

How does the serpentine belt work on a car?

Most cars today have a single belt, called a serpentine belt. In the past, two or even three belts were used. The serpentine belt connects all the accessories on the engine to the main drive pulley, which is turned by the engine. As the pulley turns, the belt moves.

When to replace belt on Jeep Liberty L engine?

In this section . Jan 13, · Serpentine belt replacement on Jeep Liberty L engine. Created on January 13, using FlipShare. Jeep Water Pump Replacement-Part 3 of 5 – Duration: Jan 16, · schematron.org In this video, 1A Auto shows you how to repair, install, fix, change or replace a broken, noisy, squeaky, worn or groaning.

Is the belt routing the same for all Jeep engines?

Periodic drive belt tensioning is not necessary, because an automatic spring- loaded tensioner is Accessory drive belt routing-Jeep L and L engines. Is this belt routing the same for ALL L engines or for a specific year? The dealer serviceman (who had to look it up by the way) gave me a.

What happens when a serpentine belt is worn?

A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function. If your serpentine belt needs to be replaced, it can be done using only common hand tools.

When to replace the serpentine belt on a Land Rover?

The serpentine belt is tensioned by a hydraulic or spring-loaded automatic tensioner. Some older cars use a serpentine belt to drive most accessories but will also have a shorter v-style belt to drive, for example, the power steering pump. Regularly scheduled maintenance. Typically, belt manufacturers recommend belt replacement at 90,000 miles.

What happens if the serpentine belt goes bad?

Serpentine belt problems that result in the alternator not charging may cause the battery to discharge, which will result in loss of electrical power to the vehicle. Additionally, if a deteriorated belt breaks and that belt drives the water pump, the engine will overheat in a matter of seconds.

What makes up the serpentine belt in a car?

A serpentine belt is a relatively long, flat, multi-ribbed belt that is driven by the engine’s crankshaft pulley. The belt drives many, and often all, of the engine accessories such as the alternator, air conditioning compressor, power steering pump, water pump, and air pump.

Can a worn belt damage a Jeep Cherokee?

Worn belts can damage components such as your AC, battery, power steering and cooling system in your 2014 Jeep Cherokee Latitude 3.2L V6 About Us Maintenance Parts & Tools Contact English SpanishFrench Search Home Jeep Cherokee 2014 Belts / Check Check the Belts: 2014-2019 Jeep Cherokee 1. Getting Started – Prepare for the repair

What kind of engine does a 2014 Jeep Cherokee have?

2014 Jeep Cherokee Latitude 3.2L V6 Check for a blown engine fuse Odd electrical problems that come out of nowhere can often signify a blown engine fuse – check and change yours here! 2014 Jeep Cherokee Latitude 3.2L V6

Why is the seat belt on my Jeep not retracting?

Recently the seat belt hasn’t been retracting. I took a much closer look at it and the area on the pillar where it goes into the door, there is a small crack in the plastic, pressing on the belt.

Why is my Jeep Grand Cherokee not shifting?

Matthew Wright has been a freelance writer and editor for over 10 years and an automotive repair professional for three decades specializing in European vintage vehicles. There is a common issue with shifting on a number of Jeep Grand Cherokee models as they age and their mileage increases.

What’s the fan belt routing on a 1998 Jeep Wrangler?

This diagram shows the fan belt routing for a ’98 TJ, 2.5L or 4.0 L, with power steering. This diagram shows the fan belt routing for a ’98 TJ, 2.5L or 4.0 L, with the air conditioning and power steering.

Where can I find a serpentine belt routing diagram?

Select the specific year and make of your vehicle. Take note of the Illustration number and then Scroll to the bottom of the page to find your Free Serpentine Belt Routing Diagram. What’s that squeal coming from under the hood?

How do you remove a serpentine belt from a jeep?

While the tension is removed from the belt, pull the belt towards the front of the vehicle (shown by green arrow below) and slip it off of the tensioner. If you have difficulty slipping the belt off of the tensioner, try to slide it off of one of the many other pulleys instead. Step 4 Now you can release pressure on the tensioner.

How can you tell the difference between a serpentine belt and a new belt?

Slide the old belt off of the pulleys while holding the belt tensioner pulley in place. Release the pulley after removing the belt. Compare the old serpentine belt with the new one. The new belt may be up to an inch shorter than the old one due to stretching.

What are serpentine belts on a 1998 Oldsmobile?

Most four-cylinder and six-cylinder engines used in the 1998 Oldsmobile lineup feature serpentine belts. These are one-piece belts that run the alternator, A/C compressor, power steering and water pump. These belts are easier to remove and last longer than ordinary V-belts.

https://www.youtube.com/watch?v=xdojVnsAZWM

What is the serpentine belt in an engine?

Serpentine Belt, as you may have heard of, is a robust rubber belt of exclusive high quality. It is a crucial part of almost every engine system. The operation and working of some of the major parts of the engines system like an air pump, water pump, air conditioning compressor, power steering pump depend on the serpentine belt.

Navigation