How to remove the front drive shaft on a Nissan Sentra?

Loosen the wheel hub lock nut. Using a piece of wood and a suitable tool, tap on the wheel hub lock nut to disengage the drive shaft from the wheel hub and bearing. Do not place the drive shaft joint at an extreme angle. Also be careful not to overextend slide joint. Do not allow the drive shaft to hang down without support.

How to remove the front wheel sensor on a Nissan Sentra?

1 Remove the wheel sensor bolt. Position the wheel sensor and the wheel sensor harness aside. Refer to BRC-106, “FRONT WHEEL SENSOR : Removal and Installation”. 2 Remove the cotter pin from the drive shaft. 3 Remove the nut retainer from the wheel hub lock nut. 4 Hold the wheel hub and bearing using Tool (A). Loosen the wheel hub lock nut.

How to install wheel studs on Nissan Sentra?

Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B). Check that there is no clearance between the wheel stud and the wheel hub and bearing. Clean the mating surfaces of the wheel hub lock nut and the wheel hub and bearing. Do not apply lubricating oil to these mating surfaces.

How to remove disc brake rotor from Nissan Sentra?

Position the brake caliper aside with wire. Refer to BR-41, “BRAKE CALIPER ASSEMBLY : Removal and Installation”. Do not depress the brake pedal while the brake caliper is removed. Put alignment marks (A) on the disc brake rotor and on the wheel hub and bearing. Remove the disc brake rotor.

How much torque does a hub bearing have?

Hub Bearing Torque Specification Guide 2010 Make year Model Front torque ft-lbs/Nm Rear torque ft-lbs/Nm

Remove the nut retainer from the wheel hub lock nut. Hold the wheel hub and bearing using Tool (A). Loosen the wheel hub lock nut. Using a piece of wood and a suitable tool, tap on the wheel hub lock nut to disengage the drive shaft from the wheel hub and bearing. Do not place the drive shaft joint at an extreme angle.

Which is the best CV axle for Nissan Sentra?

Shop AutoZone for Nissan Datsun Sentra CV Axle. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only Your Nissan Sentra seems so elegant that it’s hard to imagine it ever having any mechanical problems.

How to remove a severely stuck CV axle / CV joint?

HOW TO REMOVE A SEVERELY STUCK CV AXLE / CV JOINT FOR CHEAP | DIY CUSTOM REMOVAL TOOL – WORKS! If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

When to submit claim for Nissan transmission class action?

Submit your claim by January 30, 2020 to receive your potential award! The settlement will benefit individuals who purchased or leased a 2013 to 2017 Nissan Sentra, 2014 to 2017 Nissan Versa Note, and/or a 2012 to 2017 Nissan Versa vehicle equipped with a continuously variable transmission.

What causes a CV axle to click when turning?

When CV axles become excessively worn, the joints will become loose and click when turning. The clicks may become louder or more pronounced during sharper and faster turns, and will be heard on the side with the faulty CV shaft.

What are the symptoms of a bad cv shaft assembly?

1. Loud clicking noises when turning. One of the most common and most noticeable symptoms of a bad or failing CV axle shaft assembly is an audible clicking noise when turning.

How to install a front drive shaft on a Nissan Sentra?

Do not reuse the differential side oil seal. Place Tool (A) onto the differential side oil seal to prevent damage to the oil seal while inserting the drive shaft. Slide drive shaft sliding joint and tap with a hammer to install securely. Check that circular clip is completely engaged.

What’s the best way to change an axle?

By this time, you can put the wheel back on the vehicle (again, the same as you would when changing a tire). After the wheel is on, you can lower the car off the jack and jack stands. Tighten the axle nut. Finally, you can retighten the axle nut once the vehicle is back on the ground.

Can a remanufactured front drive axle be replaced?

You can save some money by buying a remanufactured axle, which will be virtually as good as new. The refurbishing process involves regrinding all the grooves in the inner and outer halves of the joint to a standard oversize, and replacing the cage and ball bearings with new oversize ones.

How are the wheels connected to the transaxle?

Your CV joint has failed. The wheels of your front-drive vehicle are connected to the transaxle via axles that have constant-velocity-type universal joints at each end. There is an inner and outer joint on the left and right axles.

Navigation