How to know if your Mercedes Benz has an AC problem?
Start the car and turn on the AC. (make sure the EC button it off!) Press and hold the REST button for 5 seconds or so. The display will change from your temperature settings to a diagnostic mode The number on the left is the sensor ID and the number on the right is the value. Use the left and right “Auto” buttons to cycle through the sensors.
What should the air pressure be in a Mercedes Benz?
With the car off the pressure readings should be about the same as ambient temp. in degrees F. If the outside temp is say 80 degrees F, then the pressures on both gauges should be around 80 psi. If the pressures are ok, the compressor should kick on when a/c is requested. If the compressor does not come on, then there is an electrical concern.
Why does my AC blow hot air but not cold air?
The reading for this sensor… sensor 05 for my 1998 C280 was 159 with the car running for 10 min and 158 without starting the car in the morning after a night with outside temp 80. The problem I have is that ac blows hot/warm/outside temp air initially, then it blows cold air for 1 or 2 min then it blows outside air.
What causes a Mercedes Benz air conditioner to blow a fuse?
Finally, check the clutch itself to make sure it is not defective. If there is voltage going to the clutch, a fuse may be blown. A blown fuse would indicate that the system may not have enough refrigerant pressure to tip the low-pressure cutoff switch that cycles the compressor.
How to troubleshoot your Mercedes Benz air conditioner?
Identify the location of your compressor. Look at the pullyer and you should be able to see if it spining or not. The engine running turn the A/C on max cool, set fans high, and make sure that the clutch is engaging on the compressor. The pulley spins any time the engine is running. The center part of the A/C pulley only engages when the A/C is on.
With the car off the pressure readings should be about the same as ambient temp. in degrees F. If the outside temp is say 80 degrees F, then the pressures on both gauges should be around 80 psi. If the pressures are ok, the compressor should kick on when a/c is requested. If the compressor does not come on, then there is an electrical concern.
What does a / C compressor do in Mercedes Benz?
Being the heart of the entire system, the A/C compressor’s role is to add pressure by taking the refrigerant and compressing it. Thus, it is important to understand how to check if the A/C compressor is engaging or not so as to avoid exorbitant fees for Mercedes Benz repair Laguna Niguel. First, we make sure we have the right tools.
Why does my Mercedes air conditioner keep blowing hot air?
In many models, the AC keeps blowing hot air even after recharging the coolant. It is a frustrating problem, especially during the summer, when it is almost impossible to drive a car without the AC on. A Mercedes air conditioning reset is a possible solution. Do you know how to do it? Is there any other way to fix the glitch?
How to troubleshoot your Mercedes medic air conditioner?
Turn the A/C ON. If you have an Economy button make sure that is off. Make sure fan is on HIGH, temperature selector is turned all the way to COLD, and that the A/C and recirculate light indicators are on. Set the temperature to cold, the lowest setting. Set the cooling fans on high on the climate control.
How does Mercedes Benz air conditioner system work?
While the pictures on this article are of Mercedes Benz cars, this guide is written to apply to all makes and models. How the A/C System Works. A/C compressor not engaging.
What is the recirculated air button on a Mercedes?
This is as far as the cylinder will go without cranking the engine. Press and hold the defrost and recirculated air buttons simultaneously. The defrost button has three lines going through it, while the recirculated air button has a picture of a car with a curved line through it.
In many models, the AC keeps blowing hot air even after recharging the coolant. It is a frustrating problem, especially during the summer, when it is almost impossible to drive a car without the AC on. A Mercedes air conditioning reset is a possible solution. Do you know how to do it? Is there any other way to fix the glitch?
Why is my a / C CLUTCH not working on my Mercedes?
The A/C compressor clutch engages to create the high pressure in the refrigerant and it’s state is controlled by the Air Conditioner Control Unit. If there are error codes on the A/C Control Unit the compressor will not engage and you will need to reset the fault codes using a diagnostic scanner such as the Launch Creader or iCarsoft MB II.
Why does my Mercedes Benz make a clicking noise?
It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.
Start the car and turn on the AC. (make sure the EC button it off!) Press and hold the REST button for 5 seconds or so. The display will change from your temperature settings to a diagnostic mode The number on the left is the sensor ID and the number on the right is the value. Use the left and right “Auto” buttons to cycle through the sensors.
It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.
How do you defrost a Mercedes Benz without cranking the engine?
Insert the key into the Mercedes ignition and turn the ignition cylinder to the “2” position. This is as far as the cylinder will go without cranking the engine. Press and hold the defrost and recirculated air buttons simultaneously.
What should I do if my Mercedes engine stops working?
Be aware that if you reset the unit and it again stops working, you need to take the vehicle in to the dealership for repairs. Insert the key into the Mercedes ignition and turn the ignition cylinder to the “2” position.