How to adjust the clutch cable on a Harley Davidson?

In this video I show you how to adjust the clutch cable on a 2009 Harley Davidson Softail Custom. The proper free play between the end of the clutch cable or cable Ferrule and the clutch lever housing is 1/16″ to 1/8″. Thanks for Watching! Loading…

Why does my Clutch not release on my Harley?

Clutch is not adjusted properly if it won’t release. The banging into gear is somewhat normal for a Harley…the clutch pack does not completely stop moving when disengaged. Talk to BDL…soft clutch..and no banging. I have to review the motor up a little to disengage the clutch when stopping. It is 2003 police edition Harley Davidson.

Who are the manufacturers of Harley Davidson clutch cables?

All the Harley-Davidson clutch cables we carry are made only by industry leading manufacturers like Barrett, Motion Pro, Magnum, J&P Cycles, and V-Twin Manufacturing. While you’re upgrading your clutch cables, now’s a great time to upgrade your Harley Idle Cables, and Harley Throttle Cables. Hey There. How can we help you today?

How do you adjust the clutch on a Softail?

This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. Bob teaches you how to adjust the clutch and primary chain on your Harley Softail or Dyna model.

What’s the best way to adjust a clutch?

Use a combination of your Allen key and wrench to loosen the jam nut on your clutch adjuster. RevZilla photo. At this point, you are ready to adjust the clutch. Using your fingers, tighten the clutch adjuster until it bottoms out. Do not torque it. Do not pinch harder and try to be sure it is really snug. When it bottoms out, stop. End of story.

What happens when you add Slack to clutch cable?

By adding slack into the clutch cable, what you are actually doing is collapsing the cable housing that the cable pushes against. In doing so, you are removing any tension, and when complete you should be able to squeeze the clutch lever all the way without any resistance.

How do you adjust the clutch on an old car?

This method is used on some old cars. Wedge the clutch pedal in the fully raised position with a block of wood. Locate the clutch cable and find where the outer cable is seated against its cable stop on the edge of the bell housing. The locknut and the adjuster nut are at the end of the outer cable, next to the cable stop.

How often should you change the clutch linkage?

This is known as clutch drag, and it can cause difficulties in heavy traffic. It is generally better, however to have too much play in the clutch linkage than too little. The linkage should be checked and, if necessary, adjusted about every 6,000 miles or 10,000km, or as specified in the maker’s service schedule.

Where is the clearance on a clutch located?

The clearance is usually measured either at the operating lever or at the pedal. The typical conventional clutch linkage is an inner cable sliding in an outer sheath. The top end of the cable is attached to the clutch pedal and the bottom end to the clutch operating lever.

When to change the clutch on a Harley Davidson Road King?

The Road King’s clutch should be adjusted after the first 1,000 miles and then every 5,000 miles thereafter. The Harley-Davidson Road Glide motorcycle is a touring-cruiser model with a wet clutch system supporting a five-speed transmission. This clutch should be adjusted after the first 1,000 miles and then every 5,000 miles thereafter.

How do you adjust the clutch on a Harley?

Slide the rubber boot around the clutch cable adjuster down the cable away from the adjustment hardware. Loosen the jam nut on the cable with an open-ended wrench. Turn the adjuster nut with an SAE open-ended wrench to add maximum free play in the clutch hand lever on the left handlebar. 3.

What kind of clutch does a Harley Davidson use?

Off-Road Clutch Covers Clutch Tools for Harley Davidson / Victory Clutch Spring Conversion Kits Fitting Assortments/ Indian Clutch Shaft Arm/ Wheel Weights Apparel Bikes for Sale Site Search Warranty MAP Policy Catalog (PDF)

What kind of cable do you need for a Barnett clutch?

Barnett News BARNETT UNIVERSAL INTERNAL THROTTLE CABLE more >> BARNETT EP KIT AND H-D DIAPHRAGM SPRING VIDEO more >> BARNETT COIL SPRING CONVERSION KITS- INSTALL VIDEO more >> BARNETT INSTALL VIDEO FROM FIX MY HOG more >> UNION MOTO INSTALLS A BARNETT CLUTCH IN 20 SECONDS more >> Barnett Videos Fix My Hog- Barnett Control Cables

Navigation