How much does it cost to sand and refinish hardwood floors NZ?
Sanding and coating your floor with polyurethane will vary from $45 per m2 to $55 per m2. Installation of a floor can vary from $75 per m2 to $120 per m2, Timber can vary from $80 per m2 to $300 per m2 depending on species. Floor prep can vary from $12 per m2 to $35 per m2.
How much does it cost to repair a damaged wood floor?
Hardwood floor repair costs $949 on average and typically ranges between $441 and $1,459. Some homeowners report repairs hitting $3,000. You’ll spend $2 to $25 per square foot on average, depending on the fix for the damage you have. Some reports have repairs costing up to $100 per square foot.
How do you restore a timber floor?
By sanding and polishing timber you can have any floors looking as new again. A floor sanding smooths out the surface, restores damaged floors and removes scratches from the surface. Whereas adding a floor stain or finish to your wooden floors after sanding can make the floors pristine and shiny once again.
What does it cost to sand and refinish hardwood floors?
Expect to pay $1.50 to $4 per square foot, or $340 to $900 for a 15-by-15-foot room, to thoroughly refinish a hardwood floor, including sanding down the top layer to bare wood putting several layers of new finish like polyurethane.
Can I sand my floors myself?
Sanding wood floors is a time consuming but relatively easy procedure. Sanding wood floors & refinishing yourself will definitely save money, and even an inexperienced homeowner can likely do a better job than the lowest bidding handyperson who quotes on it.
Can scratched wood floors be repaired?
Most hardwood flooring scratch repair is easily accomplished with a little elbow grease, a small can of stain, and a fine-grit sandpaper. After sanding in the direction of the grain, apply a tiny amount of stain.
Can wood floors be replaced?
When your floors have gone through a lot and the damage is extensive, you should consider replacing them. Another reason you might want to replace hardwood floors is to install a different style or color. This flooring type typically lasts between 20 and 100 years.
How do you clean old damaged wood floors?
Spray a small amount of hardwood cleaner onto the floor, and then wipe the floor down with a dry terry cloth mop or dust mop. If your floor is riddled with spots, stains, scuff marks, or debris, remove them with mineral spirits and then mop the area thoroughly.
How do you freshen old wood floors?
Sweep or vacuum, then mop with a commercial wood floor cleaner or solution of a quarter-cup of dish soap and a gallon of warm water to lift any lingering grime. Give the floors a final pass with a clean, water-dampened mop to remove any cleaner residue. Dry completely with a soft, clean towel.
Which is the best floor restoration company in New Zealand?
Floorsanding NZ offers Residential Restorations or a full Commercial Timber Floor Restoration. Floorsanding NZ has the skills and experience for any job. Floorsanding NZ works as Floor Sanders in Auckland and Manukau areas.
Is there a company that restores timber floors?
At Floor Restorations we restore and repair timber floors in both residential and commercial properties across the Auckland region. With over 20 years experience in the flooring industry we can provide knowledgeable advice for your unique floor requirements. We do everything from repairs to sanding and coating using guaranteed quality products.
Where can I get hardwood flooring in West Auckland?
Original Flooring in West Auckland provides professional floor sanding and hardwood floor repair and restoration services that will breathe new life into your wooden flooring. Sun damage, scratches and wear and tear can all be fixed with our professional sanding and finishing services.
How is the finishing process for just timber flooring?
When it comes to finishing the flooring installation, the team at Just Timber Floors has all the sanding and coating techniques covered to bring the beauty out of your timber flooring. After your timber floor is laid, the finishing process is then underway with sanding and coating.