How long to replace steering rack and pinion?
Watch this video to learn how to replace your Jeep Liberty steering rack and pinion in under two hours. Impress your friends, your boss, your wife. Heck, your wife will figure it takes at least six hours to replace and youll have time to hang out at the hair salon or even the gym like me! Loading…
Is the power steering rack and pinion leaking?
He also stated a lot of the WK2 he gets up in the air has leaking boots on the steering rack and pinion. See link below for TSB 19-006-10 – Fluid Weeping at Rack & Pinion. It applies to 2011 GCs built between May 20 2010 and August 19 2010. Had the rack in my 2011 GCX replaced back in November 2013 – just under the 3 year warranty window.
Where is the leaking power steering rack on a jeep?
Now, less than a year and less than 5,000 miles later, the replacement rack is now showing signs of leaking. Just like the original rack, the leak is on the passenger side bellow. Has anyone had the rack replaced multiple times with Jeep picking up the tab?
When was the steering gear replaced on my Jeep?
They asked if my Jeep had ever had the steering gear replaced, and the rep said yes, in 2010 while still under the original 3 year warranty. With that in mind, I asked if this had already been replaced, then is there any way that Jeep would cover the cost of the repair, as I am obviously beyond any warranty period.
Watch this video to learn how to replace your Jeep Liberty steering rack and pinion in under two hours. Impress your friends, your boss, your wife. Heck, your wife will figure it takes at least six hours to replace and youll have time to hang out at the hair salon or even the gym like me! Loading…
How to install energy suspension’s rack and pinion bushings?
If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: 8p1l-guZfYr426uZ)
What’s the best way to remove a steering rack bushing?
Tip: The best way to remove steering rack bushings is to hit them with the ball end of a ball-peen hammer. Refer to your service manual for the manufacturer’s recommended steps for this process.
How do you replace a steering rack bolt?
Once the bolt has been removed, pull the steering rack free from the bushing/mount and let it hang until you remove the other mounts and bushings. Warning: Anytime you are replacing bushings, it should always be done in pairs, or all of them during the same service.
How do you remove a pinion mount on a jeep?
After the bolts from the bushings are removed, and the mount from the front of the differential is off, the entire assembly will be free to hang down and rotate to allow access to the bushings. This was the hard part. The bushings are press fit into the housing, and mine we extremely difficult to remove.
Can you change the bushing on a jeep?
I put the Jeep on the lift and looked at the bushings, and only the one on the front of the diff looked bad, the other one on the side of the diff looked fine, and I couldn’t really see the one on top. I figured since the one looked pretty bad, and the other looked fine, I could go the short route and only change one on the front.
How do you reassembly a differential pinion mount?
When the new bushing (s) are in, reassembly is the reverse of removal (obviously). To get the nut on the bolt for the upper bushing, I had to set the nut in the socket and hold the wrench up against the bolt hole while using my other hand to slide the bolt in the hole.
Where does the steering column go in rack and pinion?
There is a seal where your steering column enters the rack and pinion assembly, then a seal where each tie rod attaches. Each of these seals have to keep high-pressure power steering fluid contained while allowing the steering column to rotate and the tie rods to move as well.
What to do about a rack and pinion leak?
You can simply and quickly restore the seals in your rack and pinion without ever removing it. Adding BlueDevil Power Steering Stop Leak to your power steering reservoir today will start to seal your power steering leaks immediately and is guaranteed to permanently seal your rack and pinion leak within a few days of driving.
What happens when a rack and pinion goes out?
It is important to be aware of what happens when rack and pinion goes out. When a pinion is on the verge of failure it can be very difficult to steer, however, if a rack or pinion goes out you will lose complete control of steering.
There is a seal where your steering column enters the rack and pinion assembly, then a seal where each tie rod attaches. Each of these seals have to keep high-pressure power steering fluid contained while allowing the steering column to rotate and the tie rods to move as well.
Do you need to replace rack and pinion?
Most rack and pinion leaks will require the replacement of the entire rack and pinion assembly even if most of it works just fine. The good news is you do have another alternative to an expensive replacement.
Why do I have a leak in my rack and pinion?
However, it is more likely that your power steering system will develop a leak at one of the seals on your rack and pinion. There is a seal where your steering column enters the rack and pinion assembly, then a seal where each tie rod attaches.
How do you remove a nut from a rack and pinion?
Remove the cotter pin in the castellated nut (I use pliers or wire cutters) and remove the nut with a wrench. Smack the side of the steering knuckle with a hammer to loosen the tie rod stud. At this point, the location and ease of access on what needs to be disconnected can vary among vehicles.