How does the PassLock work on a Saturn Ion 3?
The 2003 Saturn Ion 3 is equipped with the Passlock anti-theft system. The system disables the ignition if it detects that starting the car is attempted with an invalid key. When the Passlock system is activated, the security light flashes on the instrument panel. The engine cannot be started until the system resets.
When did the Saturn Ion fuse box come out?
The compact car Saturn Ion was produced from 2002 to 2007. In this article, you will find fuse box diagrams of Saturn Ion 2003, 2004, 2005, 2006 and 2007, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
Is there an anti theft system on a Saturn Ion?
But most of today’s vehicles come equipped with an anti-theft system that is integrated into the vehicle’s computers. The 2007 Saturn Ion is one of them. The Ion uses two systems that provide different functions, but for the same purpose: to prevent theft.
How to reset a security system on a Saturn Ion?
To reset the system, get in the car and shut the door. Turn the key on to the “Run” position without cranking the engine. Leave the key there for exactly 10 minutes. Turn the key to the off position without removing it and back to “Run” for 10 more minutes.
The 2003 Saturn Ion 3 is equipped with the Passlock anti-theft system. The system disables the ignition if it detects that starting the car is attempted with an invalid key. When the Passlock system is activated, the security light flashes on the instrument panel. The engine cannot be started until the system resets.
The compact car Saturn Ion was produced from 2002 to 2007. In this article, you will find fuse box diagrams of Saturn Ion 2003, 2004, 2005, 2006 and 2007, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.
What happens when ignition PassLock is not reset?
The system disables the ignition if it detects that starting the car is attempted with an invalid key. When the Passlock system is activated, the security light flashes on the instrument panel. The engine cannot be started until the system resets. If the Passlock system does not automatically reset, it can be reset manually.
The system disables the ignition if it detects that starting the car is attempted with an invalid key. When the Passlock system is activated, the security light flashes on the instrument panel. The engine cannot be started until the system resets. If the Passlock system does not automatically reset, it can be reset manually.
How do I Turn Off the PassLock sensor?
•The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK. The vehicle learns the Passlock Sensor Data Code and/or resistance on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
Is there a way to reset the PassLock?
When the Passlock system is activated, the security light flashes on the instrument panel. The engine cannot be started until the system resets. If the Passlock system does not automatically reset, it can be reset manually.
What happens if I disable PassLock on my car?
If your car is stalled and you cannot start it again because of the PassLock security system, do not try to start it again and again, because it can drained your battery, and it will be difficult to start it again, even if you are able to disable the lock system.
When the Passlock system is activated, the security light flashes on the instrument panel. The engine cannot be started until the system resets. If the Passlock system does not automatically reset, it can be reset manually.
To reset the system, get in the car and shut the door. Turn the key on to the “Run” position without cranking the engine. Leave the key there for exactly 10 minutes. Turn the key to the off position without removing it and back to “Run” for 10 more minutes.
But most of today’s vehicles come equipped with an anti-theft system that is integrated into the vehicle’s computers. The 2007 Saturn Ion is one of them. The Ion uses two systems that provide different functions, but for the same purpose: to prevent theft.
How do you turn off the engine on a Saturn Ion?
Turn the key to the off position without removing it and back to “Run” for 10 more minutes. Turn the key off again and back to “Run” for 10 minutes a third. Turn the key off and then attempt to start the engine.
What kind of engine does a Saturn Ion have?
The Saturn Ion Redline was a coupe with mini suicide rear doors and powered by a factory-supercharged 2.0-liter DOHC LSJ inline four, the engine later used in the Chevy Cobalt SS. Stock, the Ion Redline made 236 horsepower and 218 lb-ft of torque.
What do you need to know about a Saturn?
This is Saturn VIN Decoder. Every Saturn has a Vehicle Identification Number (VIN). This number contains vital information about the vehicle, such as model, year of production, manufacturer, country and plant of assembly, type of engine, and more. Also if someone buy a vehicle, it is possible to check Vehicle History through VIN Number.
What does the VIN number on a Saturn mean?
Every Saturn has a Vehicle Identification Number (VIN). This number contains vital information about the vehicle, such as model, year of production, manufacturer, country and plant of assembly, type of engine, and more.
What should you know about number 8 and Saturn?
Number 8 and Saturn in Numerology. What should you know about Saturn when studying Numerology? How is Saturn tied into our numbers? Learn more here. Number 8 and Saturn in Numerology. What should you know about Saturn when studying Numerology? How is Saturn tied into our numbers? Learn more here. Astrology Astrocartography Astrology Symbols
What’s the PSI of a Saturn Ion Redline?
The Ion I drove was making a limited 8 psi in first gear (which still spun the wheels too easily), and a preposterous 16 psi in second gear on up. This sounds like a great car to have fun in all the way to school and back. You can outrun the meatheads who drive 90s Z28 Camaros.
This is Saturn VIN Decoder. Every Saturn has a Vehicle Identification Number (VIN). This number contains vital information about the vehicle, such as model, year of production, manufacturer, country and plant of assembly, type of engine, and more. Also if someone buy a vehicle, it is possible to check Vehicle History through VIN Number.
Every Saturn has a Vehicle Identification Number (VIN). This number contains vital information about the vehicle, such as model, year of production, manufacturer, country and plant of assembly, type of engine, and more.
How does the ignition switch work on a Saturn?
Saturn vehicles use a transponder inside the ignition key to prevent unauthorized engine starting. There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start.
What should I do if my Saturn ignition is not working?
Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.
How to reset ignition PassLock on a 2003 Saturn Ion 3?
If the Passlock system does not automatically reset, it can be reset manually. Turn the ignition key to the “Start” position as if you are starting the engine. Turn the ignition key to the “Run” position after two to three seconds. Leave the key in this position for 10 minutes.
How does the security system work on a Saturn Ion?
The Ion uses a passive alarm system that arm when you exit the vehicle and lock the doors with the keyless remote. If at any time the doors are opened without the use of the remote or the keys the alarm will sound. This is to prevent the theft of contents within the car.
What happens when you turn the ignition key on a Saturn?
If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.
What causes a car horn to not shut off?
A horn that won’t shut off is usually the result of a jammed mechanical component in the steering column. Examining this area requires some caution due to the airbag located here, so it’s easiest to start by disconnecting power from the horn and testing the more accessible parts of the system.
Why does my 71 Charger keep honking its horn?
Another possibility is that the relay for the horn is a “shared” component with something else. On my ’71 Charger, the relay for the horn was shared with the door open warning chime. I found this out the hard way when I left the door open for an extended period of time, the relay overheated, and the horn began sounding a continuous blast.
Why does the fuse keep blowing on my horn?
Q: Horn fuse keeps blowing. If you disconnect both horns and put a good fuse in to check if the fuse blows with them disconnected, then you have another problem with the fuse blowing and not the horns. It’s also possible that you may have another problem like a shorted harness in the steering column and the horn is the first shorted wire.
Where is the trouble code on a Saturn?
These are listed in numerical order for easy searching. When retrieving Saturn trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
Is the anti-theft system in your car a nuisance?
An anti-theft system that prevents your car from running properly is a nuisance, and while you may be thankful for it in the event of a crime, it is now causing you a great deal of inconvenience, which these steps have hopefully helped you resolve.
How to check check engine light on Saturn?
Saturn Check Engine Light Codes 1 Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2 Turn the ignition on. 3 Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).
What to do when your PassLock security light goes out?
The Body Control Moudle should re-learn the security signal, and the “SECURITY” light should go out. When it does, Turn the ignition OFF for five (5) seconds, and then try to re-start the car. The “SECURITY” light should remain off this time, and the car should keep running. If not, don’t give up.
How to relearn the PassLock sensor data code?
Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF. Turn OFF the ignition, and wait 5 seconds . Repeat steps 1 through 4, 2 more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
What should I do if my Saturn ignition key is not working?
Check the fuse to make sure that the metal strip inside the fuse is not broken or damaged in any way. If it is, replace the fuse with another fuse of the same amperage. Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start.
What are the warning lights on a Saturn?
The following are warning lights and indicators found in vehicles built by Saturn. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are over 30 of them, so search carefully!
The following are warning lights and indicators found in vehicles built by Saturn. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are over 30 of them, so search carefully!
Where is the fuse on a Saturn ignition?
Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover. Locate the fuse for the starter in the fuse panel using the fuse diagram on the underside of the fuse panel cover. Remove the fuse using a fuse puller in the fuse box.
What happens if the PassLock security light is not read?
If the incorrect code is read, the system will not allow the engine to start for four minutes—even if the correct code is received. The security light will remain on or a message will be displayed on the Driver Information Center (depending on the model) when this occurs. Both of these starter interrupt systems are very effective on their own.
What happens if you have the wrong PassLock code?
Also, the ignition lock cylinder must be rotated to the “crank” position. If the incorrect code is read, the system will not allow the engine to start for four minutes—even if the correct code is received. The security light will remain on or a message will be displayed on the Driver Information Center (depending on the model) when this occurs.
What should I do if my PassLock security light goes off?
If nothing happens or the engine starts and dies, the security light will be flashing. Wait ten minutes. The flashing light should go off or illuminate without flashing. When it does, turn the ignition off, wait twenty seconds, and then try to start the engine. If it starts and runs, everything is okay.
When does the Toyota Corolla security light go off?
If nothing happens or the engine starts and dies, the security light will be flashing. Wait ten minutes. The flashing light should go off or illuminate without flashing. When it does, turn the ignition off, wait twenty seconds, and then try to start the engine.
Turn the key to the off position without removing it and back to “Run” for 10 more minutes. Turn the key off again and back to “Run” for 10 minutes a third. Turn the key off and then attempt to start the engine.
What happens when the PassLock system detects a fault?
When the system detects a fault, the warning light will illuminate or a message will be displayed on the DIC, depending on the model. If a fault occurs while driving, the engine may or may not start after turning the ignition off. If a fault occurs when trying to start the vehicle, it probably won’t start.
What happens if you turn off the PassLock system?
It prevents the car from starting with the wrong ignition key. Problems do occur with the PassLock system when your vehicle stalls and the theft system light illuminates on the dashboard. The vehicle will not start and the PassLock system will need to be disabled and reset before you can start the vehicle again. Thankfully this is an easy fix.
How do you disable the PassLock system on a GM car?
How to Disable a GM PassLock System. Look at the dashboard and locate the theft system light. It will be blinking on and off. Wait for 10 to 15 minutes until the light stops flashing and stays on. Turn the ignition to the “Off” position to disable the PassLock system, and wait for 20 seconds for the system to reset.
When do you turn off the PassLock system?
The vehicle learns the Passlock Sensor Data Code and/or resistance on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 12. Your all done, Solder all your new connections.
Can You disable the PassLock on a GM car?
The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.
How long does it take for PassLock sensor to turn off?
•Observe the security light located in the instrument cluster, after approximately 10 minutes the security light will turn OFF. Turn OFF the ignition, and wait 5 seconds. •The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
How to reset the PassLock 3 security system?
Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 6. Wait 10 minutes or until the SECURITY light to turn off. 7.
Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 6. Wait 10 minutes or until the SECURITY light to turn off. 7.
What does the P0300 Saturn engine code mean?
Start by checking for intake leaks, intake gaskets are commonly caused by multi-cylinder misfiring. If no leak is found the next step is to replace the spark plugs. If the problem persists more tests need to be done to diagnose the problem, see “Possible Causes”. The cost to diagnose the P0300 SATURN code is 1.0 hour of labor.
How much does it cost to repair a Saturn P0300?
The cost to diagnose the P0300 SATURN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? Engine Light ON (or Service Engine Soon Warning Light)
How do I Turn Off the PassLock security light?
1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine. If it starts and run, the system has reset.
What happens when the PassLock code is clear?
The BCM will enter fail enable mode and will allow the engine to start and run. The SECURITY light will be ON steady. The code will clear once the BCM senses normal voltage, but will store the code as a history code for the next 100 concurrent ignition cycles.
What’s the Red PassLock light on the dash?
OK, all good, I thought. I turned the truck off, went to use the key fob to lock the doors and saw that the red passlock light on the dash is now blinking when the truck is locked. Now, this may be normal and I never really noticed it before, as I don’t usually look in the window when I lock the truck.
What to do if your PassLock security light flashes?
“After attempting to start the engine, if the “SECURITY” light flashes or stays on, wait ten minutes with the key in ON until the light goes off. Then turn the ignition to OFF before attempting to start the engine again.” This normally works! Unfortunately, a few weeks later, you will probably have to go through the entire routine again.
Why is the PassLock indicator light not blinking?
The truck idled fine in the driveway and the light never turned on or blinked while it was running, which as I understand it, is when trouble is a brewing. I asked the same question on the 355 site, but I thought why not hit you guys up too.
When does the PassLock light work on a GMC Canyon?
It only works with PassLock when the key is in the on or start positions. With my truck, the security light flashes five times after the doors are locked with the remote, then stops. It does not continue to flash.
How does the PASSKey System on a Saturn Ion work?
The PASSKEY system uses an exciter coil located inside the key lock tumbler that detects the correct key being inserted and turned to start the car. When the correct key is turned in the cylinder it sends a signal to the computer which will then allow the fuel injectors to function.