How do you reset the turn signal on a Harley Davidson?
Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.
How do you reset the turn signal on a Dyna Glide?
Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.
Where can I replace light bulbs on a Harley Davidson touring?
This article applies to the Harley Davidson Touring (1991-2016). The basic turn signal light bulb replacement operation is fairly simple and most anyone can do this at home. Turn signal light bulbs are relatively cheap and easy to find at any local auto parts store. They are exactly the same as the bulbs used in a lot of cars today.
Why is the right turn signal light not working?
The right turn signal light and the neutral light does not light. What do you call these indicators lights and where can you get them? Hi William. Those are, simply, indicator lights. They are sealed. There are no bulbs to change for the indicators on your year/model. Usually, when one fails, however, it is due to a bad connection or switch.
Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.
Why is my hazard light not working on my Harley?
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.
What to do if left turn signal is not working?
If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled. If you apply 12 vdc to the (Lt out) pin -the Left turn signal lights should come on. (you’ve just bypassed the TSM) Next.. connect a jumper from (Lt in)pin to (Lt out) pin & press the Left turn signal switch.
What to do if your turn signal doesn’t cancel?
If your turn signal doesn’t cancel one way or the other after turning a corner, a turn signal spring is probably broken and needs replaced. Loading…
How to reset the turn signal on a Harley Davidson Dyna Glide?
Press the reset button again and the display will read “PSSPt.” Press the reset button a few times until the first “S” is flashing, then press and hold it for five seconds. The error codes should now display on the odometer. Press and hold the odometer reset button for five seconds to clear each code.
Why is my turn signal not working on my Harley?
These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse. Fixing these problems could lead to the module clearing its own code. Accessing the diagnostics menu requires you to press several of the accessory switches in a very specific manner, within a short amount of time.
How do you fix a speed sensor on a Harley?
Unplug your turn signals from behind your signal bar, or from inside your taillight (depending on the year of your Heritage). Use a small 1/2″socket, or a ratcheting box wrench to remove the two retaining bolts from inside the fender. It is, usually best to clean and reuse your stock hardware. Reinstall with red Loctite.
Why does my Speedo not work on my Harley?
Speedo works when it wants but only at highway speeds and again randomly. Now blinkers are starting too work intermittently. Any ideas? Don’t believe both switches would go at same time, Short maybe or relay. Not sure and I would appreciate any ideas. Might be a failing Harley speed sensor. Remove the sensor and see if it needs to be cleaned.
Why does my turn signal keep turning on?
Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse. Fixing these problems could lead to the module clearing its own code.