How do you remove a harmonic balancer unit?
Step 3: Remove the harmonic balancer bolt. Remove the harmonic balancer bolt by using the strap wrench to hold the balancer still. Hold it still while loosening the bolt with a socket and ratchet handle or breaker bar. It will be very tight, so pull hard. Step 4: Remove the harmonic balancer unit.
Can a harmonic balancer be installed on a Chevy 350?
The final step to installing the harmonic balancer is the one that is most often overlooked. The bolt is commonly tightened until it cannot be tightened anymore. Proper installation requires that the 350’s harmonic balancer’s bolt be tightened to only 60 pound-feet of torque to avoid damaging the balancer, the crankshaft, or both.
Can a torque wrench be used on a harmonic balancer?
The bolt is commonly tightened until it cannot be tightened anymore. Proper installation requires that the 350’s harmonic balancer’s bolt be tightened to only 60 pound-feet of torque to avoid damaging the balancer, the crankshaft, or both. Therefore, only a torque wrench should be used to tighten the bolt to the proper torque setting.
What causes a crankshaft harmonic balancer to fail?
On many engines, the harmonic balancer is integrated into the crank pulley. They do not fail often, but excess engine vibrations and misaligned timing marks are among the symptoms of a bad or failing crankshaft harmonic balancer
Where is the harmonic balancer on a car?
Step 1: Prepare the vehicle. Jack the vehicle up high enough to obtain access to the harmonic balancer, located on the front of the motor and attached to the crankshaft. Step 2: Remove the accessory drive belts. On many modern vehicles, there is an automatic, spring-loaded belt tensioner that can be rotated to loosen the belt.
Step 3: Remove the harmonic balancer bolt. Remove the harmonic balancer bolt by using the strap wrench to hold the balancer still. Hold it still while loosening the bolt with a socket and ratchet handle or breaker bar. It will be very tight, so pull hard. Step 4: Remove the harmonic balancer unit.
Step 1: Prepare the vehicle. Jack the vehicle up high enough to obtain access to the harmonic balancer, located on the front of the motor and attached to the crankshaft. Step 2: Remove the accessory drive belts. On many modern vehicles, there is an automatic, spring-loaded belt tensioner that can be rotated to loosen the belt.
On many engines, the harmonic balancer is integrated into the crank pulley. They do not fail often, but excess engine vibrations and misaligned timing marks are among the symptoms of a bad or failing crankshaft harmonic balancer
Where can I buy a harmonic balancer puller kit?
With the rattle gun the bolt came loose straight away. I had already purchased a harmonic balancer puller kit from super-cheap for $25, however had to buy three new bolts for it. The bolts provided in the kit had the wrong thread!
Which is the best harmonic balancer installation tool?
Tool, Harmonic Balancer Installation Tool, Cadillac, Chevy, GMC, Pontiac, Small Block LS, Each Harmonic Balancer Puller, 3-Jaw Puller, 4 Forcing Rods, 1 Forcing Screw, Kit Damper Puller, Installer, Puller Plate, Installer Studs, Puller Bolts, and Storage Case, Kit Harmonic Balancer Installation Tool, Small Block Chevy, 7/16 in.-20 Thread, Kit
Where does the coolant leak from a water pump come from?
My leak appears to be coming off the back side of the pump housing, but originating above the area that i can see with a mirror. Surely somebody out there in cyberspace has seem the dark side of the moon behind the water pump and could direct me on this.
What happens if coolant leaks from the bottom of the engine?
Your vehicle’s head gasket seals the space between its cylinder head and engine block. If the head gasket fails, coolant, and engine oil may mix. You may also notice that coolant is leaking from the bottom of the engine and dripping onto the ground. Either way, a blown head gasket can be disastrous for your engine.
What’s the best way to fix a coolant leak?
The best way to fix a coolant leak is to track down the location of the leak and repair the old, damaged, or ineffective part. For example, if you have a cracked hose, replacing it is the most effective way to stop your leak. Some components naturally wear out over time.
Can a hot coolant leak cause a burn?
You must be careful when checking fluid levels, though. If the engine is not completely cool before you remove the radiator cap, you may suffer a serious burn from escaping steam or hot coolant. Therefore, you should never open the radiator cap or the coolant reservoir when your car’s engine is hot.