How can I tell if my Montero has been reset?
Turn on the ignition, but don’t try to crank the engine. Wait 5 minutes and then insert the fuse back into the fuse panel. The “check engine” light on the dash of your Montero will blink several times and then shut off. This will indicate that the computer has been reset.
What to do if you have a problem with your Mitsubishi Montero?
If there is something wrong with any of the various sensors on the Montero, the module, called an ECU, will generate a trouble code. You can get a free diagnostic scan at most auto parts stores. However, a more precise scan can be done at a Mitsubishi dealership.
How does the ETACS work on a Montero?
On your car the key immobilizer information is read by the immobilizer ecu which then compares it’s reading with a stored figure in the engine PCM. As long as you are NOT fooling with the immobilizer ecu or engine PCM, the key immobilizer is not involved here. On this model the ETACS has no influence on the key immobilizer.
What are the symptoms of a bad ECM power relay?
A bad relay may cause the vehicle to crank, but not start, or sometimes not even crank at all. 3. Battery drain or dead battery. A failed ECM power relay can also cause a battery drain or dead battery. If the relay shorts it can leave power on to the computer, even when the vehicle is turned off.
What happens when the crank sensor on a Montero fails?
When the crankshaft position sensor on your 3.0L Mitsubishi Montero fails, your engine won’t start. Here are some more specific symptoms: The vehicle will not start. The engine will turn over (crank) but won’t start. Trouble code lighting up the check engine light (CEL) on your instrument cluster.
Where is the CKP sensor on a Montero?
Crankshaft position signal (output to the PCM). Power circuit (12 Volts). The crankshaft position (CKP) sensor is located behind the timing belt and it can be tested without removing the timing belt or its components.
What are the signs of a failing ECM?
Common signs of a failing PCM/ECM/ECU include the Check Engine Light coming on, engine performance issues, and the car not starting. 1. Check Engine Light Turns On 2. Engine Stalling or Misfiring 3. Engine Performance Issues 4. Car Not Starting
On your car the key immobilizer information is read by the immobilizer ecu which then compares it’s reading with a stored figure in the engine PCM. As long as you are NOT fooling with the immobilizer ecu or engine PCM, the key immobilizer is not involved here. On this model the ETACS has no influence on the key immobilizer.
Where is the ECU fuse on a Montero?
Pull down the fuse panel cover of your Montero. The fuse panel is located in the driver side footwell, under the steering column. Locate the fuse for the electronic control unit, or ECU. Use the fuse diagram on the underside of the fuse panel cover to locate the ECU fuse. Pull the ECU fuse using the fuse pullers that are mounted in the fuse panel.
How do you change the speed sensor on a Montero?
Turn the nut at the base of the speed sensor counterclockwise with the socket set. Continue to turn the nut until the sensor comes free. Install the new speed sensor by twisting it in clockwise. Tighten it with the socket set. Plug the wiring harness into the new sensor.
What does check engine light on Mitsubishi Montero mean?
A check engine light can indicate a broad spectrum of problems with your 1997 Mitsubishi Montero Sport. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.
What kind of engine light does a 1997 Montero Sport have?
This free video provides the steps to diagnose and clear a check engine light on a 1997 Mitsubishi Montero Sport XLS 3.0L V6. The video also provides steps on how to read the 1997 Mitsubishi Montero Sport XLS 3.0L V6 trouble code About Us Maintenance Parts & Tools Contact English SpanishFrench Search Home Mitsubishi
What are the symptoms of a bad alternator in a Montero?
Here are the most common symptoms of a bad alternator in a Mitsubishi Montero: The battery light is designed to tell you that there is not enough voltage to properly charge the battery, or that the battery itself is not holding the proper voltage. In rare occasions the service engine soon light may light up.
What should the volts be on a Mitsubishi Montero?
With your Montero turned off, you’ll connect the negative side of the meter to the negative battery post or wire. You’ll then touch the positive side of the voltmeter to the positive battery wire. With the engine off, you should get a reading somewhere between 12.0 volts and 12.6 volts.
Why is there no spark in my ignition?
An ignition module requires some type of external input in order to activate. If your vehicle stalls unexpectedly during operation and will not start again, it is likely because of loose or corroded electrical connections in the ignition module. In this case, check the switch, clean oxidized terminals, and replace broken wires if necessary.
Turn on the ignition, but don’t try to crank the engine. Wait 5 minutes and then insert the fuse back into the fuse panel. The “check engine” light on the dash of your Montero will blink several times and then shut off. This will indicate that the computer has been reset.
Pull down the fuse panel cover of your Montero. The fuse panel is located in the driver side footwell, under the steering column. Locate the fuse for the electronic control unit, or ECU. Use the fuse diagram on the underside of the fuse panel cover to locate the ECU fuse. Pull the ECU fuse using the fuse pullers that are mounted in the fuse panel.
How to reset the computer on a Mitsubishi Montero?
Pull the ECU fuse using the fuse pullers that are mounted in the fuse panel. Turn on the ignition, but don’t try to crank the engine. Wait 5 minutes and then insert the fuse back into the fuse panel. The “check engine” light on the dash of your Montero will blink several times and then shut off. This will indicate that the computer has been reset.
What causes a fuel leak in a Mitsubishi Montero?
Fuel Injection Line – Finding a leak in the fuel line can be a key cause of the fuel leaks and Mitsubishi Montero problems. This leak can cause a very strong fuel odor once you stop your vehicle and park the car.
Why does my Mitsubishi Montero make a rattle noise?
The rattle noise under the car can come from your car being fully warmed up and occur only after you have been driving it for a longer distance, causing the Mitsubishi Montero problems. Accelerating and Decelerating – You might hear a rattle noise under the car when the car is accelerating or decelerating.
If there is something wrong with any of the various sensors on the Montero, the module, called an ECU, will generate a trouble code. You can get a free diagnostic scan at most auto parts stores. However, a more precise scan can be done at a Mitsubishi dealership.
Fuel Injection Line – Finding a leak in the fuel line can be a key cause of the fuel leaks and Mitsubishi Montero problems. This leak can cause a very strong fuel odor once you stop your vehicle and park the car.
The rattle noise under the car can come from your car being fully warmed up and occur only after you have been driving it for a longer distance, causing the Mitsubishi Montero problems. Accelerating and Decelerating – You might hear a rattle noise under the car when the car is accelerating or decelerating.
Pull the ECU fuse using the fuse pullers that are mounted in the fuse panel. Turn on the ignition, but don’t try to crank the engine. Wait 5 minutes and then insert the fuse back into the fuse panel. The “check engine” light on the dash of your Montero will blink several times and then shut off. This will indicate that the computer has been reset.
How do you start a Montero Sport car?
Before starters, drivers were forced to hand crank their vehicles to get them running. All versions of the Montero, including the Montero Sport, use a traditional electrical starter. Disconnect the negative (-) battery cable for safety. Use the pliers to loosen the nut and slip the cable off.
What’s the wheelbase of a 2002 Mitsubishi Montero?
The Montero Sport is a little more rounded, with standard fender flares and running boards. The Sport rides a 107.3-inch wheelbase and measures 70 inches wide, and its 68.3-inch height gives it a lower profile than the regular Montero.
Before starters, drivers were forced to hand crank their vehicles to get them running. All versions of the Montero, including the Montero Sport, use a traditional electrical starter. Disconnect the negative (-) battery cable for safety. Use the pliers to loosen the nut and slip the cable off.
What kind of battery does a Montero Sport use?
All versions of the Montero, including the Montero Sport, use a traditional electrical starter. Disconnect the negative (-) battery cable for safety. Use the pliers to loosen the nut and slip the cable off. The starter is an electrical item; disconnecting the battery will prevent shock.
What does the spark do on a Montero?
The spark allows the vehicle to crank smoothly and reliably. Before starters, drivers were forced to hand crank their vehicles to get them running. All versions of the Montero, including the Montero Sport, use a traditional electrical starter. Disconnect the negative (-) battery cable for safety.