Are there any problems with my Nissan Almera?
My Nissan Almera 1.8 2005 starts normaly and after 25-30 km the engine stops working and can not be started 1-2 minutes, after starting, the problem repeats in shorter period. The check indicator is turned on. I have made computer diagnostic and it shows 3 errors:
What’s the engine code on a Nissan Almera?
Engine on tickover Idles at 1500 revs: driving , engine hunts between gear changes at 1800 to 2500 rpm Got nats codes 1610 & 1612 engine cranks but no start no spark at plugs. Nats light on dash continuously flashes.
What to do if your Almera engine is failing?
Check the crankshaft sensor and scan your vehicle to see the codes provided. If it is the alarm that is failing, that occurred to me and the whole alarm system needed to be disconnected. After doing so, the car never failed again. Thanks for all your comments.
What to do if your Nissan Almera stalls?
The vehicle occasionally stalls and starts without a problem. But there are some other occasions, which have been more frequent lately, in which the engine does not start working again after it stalls. You need to change both the crankshaft and camshaft sensors and then reset your computer.
What’s the problem with my Nissan Almera engine?
I am driving a nissan almera 2003 model, the car is starting but when i accelerates it only comes up to 2500 revs and then it starts jerking. I replaced the MAF sensor as well as the throttle position sensor, but its still doing the same thing, please help Even though the four coils are working, coil number 1 has no spark.
What are the Nats codes for Nissan Almera?
Got nats codes 1610 & 1612 engine cranks but no start no spark at plugs. Nats light on dash continuously flashes. Any ideas thanks The engine light came on, l scanned to find fault on bank 1 sensor 1which I replace, only for it to show bank 2 sensor 2 again.
The vehicle occasionally stalls and starts without a problem. But there are some other occasions, which have been more frequent lately, in which the engine does not start working again after it stalls. You need to change both the crankshaft and camshaft sensors and then reset your computer.
My Nissan Almera 1.8 2005 starts normaly and after 25-30 km the engine stops working and can not be started 1-2 minutes, after starting, the problem repeats in shorter period. The check indicator is turned on. I have made computer diagnostic and it shows 3 errors:
Can a Sentra sensor be replaced with an Altima sensor?
You can try replacing yours with a Sentra or an Altima sensor, good luck. Good afternoon, I have a Nissan Almera 2007, which starts but does not accelerate. The first failure that appeared and was detected by the scanner was a crankshaft sensor damage. It was replaced together with a coil that was failing too.
Why does my Nissan Almera stall when I change gear?
When changing the gear to reverse the car, it usually stalls. According to my mechanic, the car stalls either when the reverse lights are failing or when there is a damaged sensor in the reverse box. I had your same problem and, in my case, it was a failure in the reverse lights.
How to reset Nissan Almera airbag warning light?
Put your key in the ignition and turn it until the dashboard lights come on. Do not start the engine. Press the button on the inside of the door (pictured below) 5 times before the airbag warning light comes on (you have about 5 seconds so don’t panic). Turn the key all the way off as soon as the airbag light goes off.
Got nats codes 1610 & 1612 engine cranks but no start no spark at plugs. Nats light on dash continuously flashes. Any ideas thanks The engine light came on, l scanned to find fault on bank 1 sensor 1which I replace, only for it to show bank 2 sensor 2 again.
Is there a problem with the timing chain on a Nissan Almera?
The timing chain is a known issue on the Almera. The timing chain will need to be adjusted, most likely tightened. This should fix your problem. Watch the video below on how to carry out this repair: It is known on the Almera for the electric windows to fail.
Why does my Almera Tino not Rev over 2000 rpm?
UK Nissan Car Mechanic 41 satisfied customers 2004 Nissan Almera Tino 1.8 petrol won’t Rev over 2000rpm 2004 Nissan Almera Tino 1.8 petrol won’t Rev over 2000rpm fault code for throttle pedal sensor and throttle body ie tps comes up I have changed both these items but still happening…
Why does my Nissan Almera stutter when I Rev the engine?
Your Almera starts fine, but it stutters and sometimes cuts out when you rev the engine. This could be a variety of issues. Your first step should be to check the airflow sensor and then test that the fuel pump is working correctly.
Can a Sentra sensor be replaced in a Nissan Almera?
You can try replacing yours with a Sentra or an Altima sensor, good luck. Good afternoon, I have a Nissan Almera 2007, which starts but does not accelerate. The first failure that appeared and was detected by the scanner was a crankshaft sensor damage.
Check the crankshaft sensor and scan your vehicle to see the codes provided. If it is the alarm that is failing, that occurred to me and the whole alarm system needed to be disconnected. After doing so, the car never failed again. Thanks for all your comments.
Why does my Almera 1.6 equation not start?
My Almera 1.6 equation has been a really good runner so far but it is becoming quite unpredictable. It won’t start at all. The battery is fully charged, the starter motor doesn’t kick in. Sometime the car would start again after few hours and then it just didn’t start again once the problem happened.
When changing the gear to reverse the car, it usually stalls. According to my mechanic, the car stalls either when the reverse lights are failing or when there is a damaged sensor in the reverse box. I had your same problem and, in my case, it was a failure in the reverse lights.
You can try replacing yours with a Sentra or an Altima sensor, good luck. Good afternoon, I have a Nissan Almera 2007, which starts but does not accelerate. The first failure that appeared and was detected by the scanner was a crankshaft sensor damage. It was replaced together with a coil that was failing too.
Why does my Nissan Almera make a hissing noise?
The engine is running rough, and there is a hissing noise coming from it, although there are no problems revealed when you do a fault check. Most likely, this is a problem with your airflow meter.
Why does my Nissan Almera fill up with condensation?
You will need to fit a replacement oxygen sensor to resolve this problem. It is known on the Almera for the headlights to fill up with condensation. This is particularly a problem on cold mornings. The best thing to do is to drill small holes at the bottom of the headlight covers in order to allow any water build up to drain out.
What is the Nats code for Nissan Almera 53?
Please help very desperate my question is for my nissan almera 53 reg having problem starting it.
Why is the immobiliser light not working on my Almera?
As the NATS light stays on and the vehicle doesn’t start this is solely on the NATS system as proved by the 2 fault codes P1614 and P1615. 1614 means that the NATS IMMU can’t see the key or the code that is set is damaged in some way.
Why is my Nissan club car not starting?
It prevents the car from starting (for some period of time, even if the key issue is rectified). P1614 merely indicates an issue with the anti-theft system because the IMMU cannot receive the key ID signal.
Is the Immobilizer light on on a Nissan?
There were no prior warning symptoms or a lit MIL earlier in the day. In fact, everything has been running great for the past few months. After trying to start it several times, I noticed that while the key/ignition was in the “ON” position, the immobilizer light was in a constant-on state.
What does p1615 Nissan immobilizer code mean?
P1615 NISSAN Meaning An immobilizer is an electronic device fitted to an automobile which prevents the engine from running unless the correct key is present. This prevents the car from being hotwired after entry has been achieved.
How is the binary code read on a Nissan Leaf?
The microcircuit inside the key is activated by a small electromagnetic field which induces current to flow inside the key body, which in turn broadcasts a unique binary code which is read by the automobile’s Engine Control Module ( ECM ).