Why is my O2 sensor still reading the same code?

If you have to drive 10 minutes before the Check Engine light comes on with the same code with the new O2 sensors, then the O2 sensor may be getting coated or contaminated where it can no longer read the oxygen content in the exhaust gasses and the voltage signal from the O2 sensor remains high.

When did I replace the O2 sensor in my van?

In February 2013, three error codes popped up (P0134, 0138, 0139), and the car was running sluggish and getting poor gas mileage. Three weeks ago, I took the van in to replace the O2 sensor. (I did not drive more than 40 miles since the codes came up).

When did Bank 1 O2 sensor stop working?

I have a 2002 Chrysler T&C limited. In September 2012, squirrels chewed through the wiring to my bank 1 O2 sensor. After a quick and easy fix, there were no issues or codes. In February 2013, three error codes popped up (P0134, 0138, 0139), and the car was running sluggish and getting poor gas mileage.

When to reset the ECU after changing an O2 sensor?

Sometimes an O2 sensor fails, and you need to replace it. Once you’ve replaced your vehicle’s O2 sensor, you’ll need to reset the ECU so it can properly gather information from the new O2 sensor.

What happens when the O2 sensor is replaced?

It’s a common problem that when the code refers to the O2 sensor, then the shop simply replaces the sensor. But the problem in many cases is not the O2 sensor. And when the set of them are replaced for no reason, you end up with a car which now has non-OEM sensors, which aren’t as good of quality as what you had in the first place.

Are there any codes for an oxygen sensor?

There are a large number of codes relating to oxygen sensor faults. There are also a lot of faults that are often incorrectly thought to be caused by a bad oxygen sensor (also referred to as an O2 Sensor). The O2 codes relating to circuit faults can be tested fairly easily.

What could cause all four 02 sensors codes to continue to show Bad?

What Could Cause All Four 02 Sensors Codes to Continue to Show Bad… What could cause all four 02 sensors codes to continue to show bad? On computer even after all sensors were replaced? I have a check engine light that has been on before I bought vehicle. I had the codes checked p0054 code and all four o2 sensors are displayed on computer.

What are the symptoms of a faulty oxygen sensor?

The most common symptom related to a faulty oxygen sensor is a sudden (significant and almost immediately noticeable) drop in your vehicle’s fuel economy. Other immediately apparent effects of a defective sensor is a drastic change in engine performance, overall power, and response.

Can you replace O2 sensor and still get check engine light on?

Replace O2 Sensor and still get Check Engine Light On. Replaced O2 Sensor and still get Check Engine Light On. 2 different shops did reads on my check engine light codes, I even paid $100 for one of them to do a full test of all sensors to identify which one was bad. Their diagnose was code P0141, oxygen sensor heater, o2 sensor had to be replaced.

Can a bad sensor cause an oxygen sensor to not work?

It turns out that most of the issues that set oxygen sensor codes are not a result of a bad sensor. So, automatically screwing in a new sensor because there’s a sensor-related code is a big gamble. A good mechanic will always use those trouble codes simply as a starting point in his diagnosis.

Why is a P0420 trouble code never a bad oxygen sensor?

NOTE: This is why a P0420 trouble code is almost never a bad oxygen sensor — because the ECM has already tested the downstream sensor. If it isn’t responding properly, it will set a trouble code. The same applies to the upstream sensor.

How do I remove the O2 sensor from my Mercedes Benz medic?

Once you place the O2 removal tool on the O2 sensor, you will need to turn it counterclockwise to remove it. Step 7: Install new oxygen sensor. Install the new oxygen sensor, which we showed you how to buy online for under under $100 in reverse order.

Do you need to replace your oxygen sensor?

Replacement of good oxygen sensors is one of the common mistakes that both seasoned auto repair mechanics and do it yourself driveway mechanics will make when tackling rich or lean diagnostic codes. I am not saying that these O2 sensor codes never require the replacement of the sensor itself.

What are the symptoms of a bad 02 sensor?

Engine Hesitation. Engine hesitation is similar to engine missing. However, engine hesitation is experienced only during acceleration, while an engine miss can be experienced both during engine acceleration and idle.

What causes 02 sensor failure?

Excess oil in the exhaust can also cause 02 sensor failure. You might also check ebay for an 02 sensor, I’ve bought a few there for less than half the price the local parts stores want. The problem isn’t caused by coolant or oil in the exhaust.

How often should O2 sensors be replaced?

Bosch recommends replacing unheated one- or two-wire O2 sensors on 1976 through early 1990s applications every 30,000 to 50,000 miles. Heated three and four-wire O2 sensors on mid-1980s through mid-1990s applications should be changed every 60,000 miles.

How often to change O2 sensor?

Heated three and four-wire O2 sensors on mid-1980s through mid-1990s applications should be changed every 60,000 miles. And on 1996 and newer OBD II-equipped vehicles, the recommended replacement interval is 100,000 miles. A good oxygen sensor is essential for good fuel economy, emissions and performance.

When do you need an oxygen sensor in a car?

You May Need an Oxygen Sensor Or You May Need Something Else Entirely When check engine lights are scanned, a p0420 code is a very common result. It’s actually a generic code, meaning it can be thrown from any vehicle after 1996.

How can I bypass the O2 sensor in my car?

Plug in the dummy oxygen/o2 sensor by rotating it clockwise. Insert it into the exhaust system and connect it to the electrical wiring. You can now lower the car onto the ground, but wait, we’re not done yet! Once your vehicle is safely lowered to the ground, you will need to start the engine.

Can a check engine light be an oxygen sensor?

It seems as though the check engine light and O2 Sensor codes have always gone hand in hand. I can’t even begin to tell you how many perfectly good sensors I’ve seen replaced for a rich/lean code, or as a cure to a service engine light that comes and goes. Fact is, when oxygen sensors were first being used, they did tend to fail.

Is there a p0134 code on my O2 sensor?

3 replacements of O2 sensor and still have P0134 code. Now told it is the PCM – Maintenance/Repairs – Car Talk Community 3 replacements of O2 sensor and still have P0134 code. Now told it is the PCM I have a 2002 Chrysler T&C limited.

What does it mean when your oxygen sensor says P0420?

Oxygen sensors are only a part of a greater system, meaning if the p0420 code (or p0141, or p0135) is thrown, that doesn’t necessarily indicate the oxygen sensors need replacement. Rather, there could be something else in that system does that’s causing the oxygen sensors to appear faulty.

How much does a P1167 oxygen sensor cost?

The cost of diagnosing the P1167 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. The Air/Fuel Ratio (A/F) sensor 1 is installed in the exhaust system and detects oxygen content in the exhaust gas.

How long does it take to diagnose Honda P1167 code?

An error occurred while retrieving sharing information. Please try again later. The cost of diagnosing the P1167 HONDA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

When does a sensor 1 heater malfunction?

If the element is not activated or the Engine Control Module (ECM) terminal voltage is a set value or less for at least a set time period when the power is drawn to the A/F sensor (sensor 1) heater, a malfunction is detected and the code is stored.

How does the resistance of an oxygen sensor change?

As you suggested, resistance in the circuit changes as the oxygen sensor heating element heats up. The circuit resistance is converting the supply voltage into heat for the heater, so the voltage drop across the heater circuit will also increase. The PCM senses the voltage drop and adjusts the duty cycle to lower the circuit on-time.

When do you need to replace your oxygen sensor?

Oxygen sensors eventually need to be replaced in all vehicles. If your vehicle’s O2 sensor is faulty, chances are there will be signs! Check this list to see if it’s time to replace YOUR vehicle’s oxygen sensors:

How long does it take O2 sensor to work?

Although your O2 Sensor should begin working immediately it is not unusual for it to take 50 to 100 miles of driving before it works correctly. If you are replacing the sensor to pass inspection make sure that you take that time to drive the car before you take it in for your test.

Why is my car sputtering after installing new O2?

Which is fine, the engine can run fine in open loop, probably wouldn’t even notice anything unless you were coming close to some performance limit or another. But when you switched to the new sensors, that confused the ECM, as it had been compensating for the bad sensor.

What should I do if my oxygen sensor fails?

Always follow the instructions in your owner’s manual for Oxygen (O2) Sensor replacement. The Oxygen (O2) Sensor is a wear item and does fail over time. This will reduce the level of emissions your vehicle puts into the atmosphere. And, At the same time keep your engine running smoothly.

Can a failing O2 sensor cause fuel surging?

In fact, the old O2 sensor was one of the first ever used to electronically modulate the ratio of fuel and air used by the engine — in a time even before what we would recognize as fuel injection today even existed. Surging is among the many problems a failing O2 sensor can cause, but it isn’t the only one.

What happens if your O2 sensor is bad?

Sudden decrease in fuel mileage. A defective O2 sensor will likely cause your air-fuel mixture to be too rich and directly affect your fuel economy. Flashing check engine light or malfunction indicator lamp in the vehicle?s dash board. Of course this can happen for other reasons as well (and a defective oxygen sensor is one of them!)

When is it time to replace your oxygen sensor?

Why is my crankshaft sensor still showing the same code?

Still showing original code saying to replace crankshaft sensor. the code for crank sensor does not mean the sensor needs to be replaced. it means the ecm does not recognise the signal, the signal is not there or it is erratic. thats why you pay for a real diag instead of a free diag from a parts person who has never fixed a car.

Can a PCM replace an O2 sensor needlessly?

In my professional experience, the PCM is seldom the cause Nevertheless, they often get replaced needlessly But if the second shop arrives at the same diagnosis, it may be the exception to the rule. The O2 sensor produces it’s own voltage. The lower the voltage is the more oxygen there is in the exhaust gasses.

What are the symptoms of a bad ECM computer?

There are a few things that can tip you off that there’s a problem. Here are the four most common symptoms of a bad ECM computer: There are many reasons your Check Engine light can turn on. These range from emissions problems to faulty O2 sensors to problems with the ECM.

Can a knock sensor cause a car ECM to fail?

There’s also a knock sensor on the engine itself. While these sensors aren’t likely to cause any catastrophic problems, failures in these areas can cause your ECM to make unnecessary adjustments that affect your car’s performance. In these cases, though, the problem is usually with the sensors, and not with the ECM.

How does the engine control module ( ECM ) work?

The ECM takes the information from the engine’s various sensors, and uses that information to calculate and tune engine spark and fuel for maximum power and efficiency. The ECM plays a crucial role in newer vehicles, where many (if not all) of the essential functions of the car are controlled by the ECM.

What are the symptoms of a bad engine control module?

1. Check Engine Light Turns On 2. Engine Stalling or Misfiring 3. Engine Performance Issues 4. Car Not Starting 5. Poor Fuel Economy The engine control module (ECM), also commonly referred to as the engine control unit (ECU) or powertrain control module (PCM), is one of the most important components found on virtually all modern vehicles.

How does the O2 sensor in a car work?

The O2 sensor in your vehicle monitors the exhaust gases coming out of the engine. It determines the amount of oxygen in the gases, which indicates how well the fuel is being burned. The O2 sensor then sends information to the electronic control unit, or ECU, the vehicle’s computer.

Can a bad O2 sensor cause incorrect readings?

A leak in the exhaust system before the O2 sensor will also cause incorrect readings. And always check for after- market modifications. These can throw a wrench into the works! The only other possibilities (however unlikely), are wiring issues, computer concerns or a bad O2 sensor!

What does it mean when your oxygen sensor is running rich?

Basic Oxygen (O2) Sensor Codes If there is too much fuel and not enough air, the engine is said to be “running rich”, or “has a rich mixture”. It will have a gassy or rotten egg smell from the exhaust, give off a burning effect to the eyes and will make black smoke.

What is the function of downstream O2 sensor?

The downstream oxygen sensor is located in the exhaust pipe after the catalytic converter. The role of the downstream oxygen sensor is to monitor the working and efficiency of the catalytic converter. There may be one or two oxygen sensors depending on the number of cylinders. The ECU compares the signal from upstream and downstream sensors.

What is a bad O2 sensor?

Bad O2 sensors are one of those car problems that most drivers tend to postpone until more serious problems occur. These symptoms will rarely cause any immediate damage, but over time, if left unattended, they can cause damage to the engine and other systems mainly through improper air-fuel mixture.

What does a bad O2 sensor do?

A bad oxygen sensor can impede the air/fuel mixture of an engine or interfere with the engine combustion, both of which can cause an engine to miss, or run irregularly.

Where is the O2 sensor located?

Oxygen sensors O2 sensors will always be located in the exhaust system. Their function is to sense how much oxygen remains in the exhaust that is flowing out of the engine, and report that information to the vehicle’s engine control computer.

Navigation