Why is my navigation not working on my car?
It is possible that one of the cables in the back of the unit has gotten loose or is disconnected. Another common error message that you will see is “Navigation is initiating please wait” Under such conditions the COMAND system works correctly except the navigation system.
What to do when your navigation system is not activated?
If you are trying to update the navigation system using an update DVD you may get an error message saying Loading Navigation. This process can take a while in some cases up to one hour. Try removing the Navi DVD, turn off your car and let it sit for one hour.
What does it mean when Mercedes says navigation cannot be activated?
After inserting the navigation DVD in your Mercedes-Benz COMAND, you get a warning message “Navigation Cannot Be Activated.” You press the NAVI button on the COMAND but get an alert message saying “”Navigation can not be activated. An error has occurred.” N1112 No data transfer between D2B master and D2B predecessor component possible.
Why is my navigation DVD not loading on my stereo?
If your stereo has only one slot for the Navigation DVD and audio CD, try inserting an audio CD or DVD to see it that works properly. If it does then the problem may be your disk and not the optical lens. If you are trying to update the navigation system using an update DVD you may get an error message saying Loading Navigation.
It is possible that one of the cables in the back of the unit has gotten loose or is disconnected. Another common error message that you will see is “Navigation is initiating please wait” Under such conditions the COMAND system works correctly except the navigation system.
What does it mean when it says navigation cannot be activated?
Error message “Navigation CanNot be Activated” usually means that the Navigation system is not being able to start up (boot up) which could be due to several reasons. Common problems include wrong DVD disk, issues with the navigation processor A40/3n2 or fault in CAN bus (controller area network) communication.
Why does my navigation screen say program cannot be read?
Now Navigation display information screen does not work properly and displays the message “A program cannot be read” My car has 66000 miles. My car has an automatic transmission. Hi there. You will need to do a hard reset on the vehicle if your navigation system is factory in design. Disconnect the battery and turn the headlights on.
What should I do if my Lexus navigation system is not working?
Turn on the vehicle and test to make sure the system is working properly. Follow the directions on the screen. This article is written for the 2001-’06 Lexus LS430 but is applicable for any Lexus or Toyota with the same navigation system. Always disconnect the battery when working on automobile electronics.
Why is my Navi CD not working properly?
Make sure the Navi disk itself isn’t damaged. If your stereo has only one slot for the Navigation DVD and audio CD, try inserting an audio CD or DVD to see it that works properly. If it does then the problem may be your disk and not the optical lens.
Why is my navigation not working on my Mercedes medic?
Reinsert the fuses and check if the error message is gone. Check all the cables and connections in the back of the COMAND or the DVD drive. Especially if work was done near those units. It is possible that one of the cables in the back of the unit has gotten loose or is disconnected.
Reinsert the fuses and check if the error message is gone. Check all the cables and connections in the back of the COMAND or the DVD drive. Especially if work was done near those units. It is possible that one of the cables in the back of the unit has gotten loose or is disconnected.
Make sure the Navi disk itself isn’t damaged. If your stereo has only one slot for the Navigation DVD and audio CD, try inserting an audio CD or DVD to see it that works properly. If it does then the problem may be your disk and not the optical lens.
Turn on the vehicle and test to make sure the system is working properly. Follow the directions on the screen. This article is written for the 2001-’06 Lexus LS430 but is applicable for any Lexus or Toyota with the same navigation system. Always disconnect the battery when working on automobile electronics.
What to do if your Navi button is not working?
Press NAVI button and wait for the system to restart. If that doesn’t work go to the next step. Try resetting the COMAND system by removing the fuse for 15 minutes. Reinsert the fuses and check if the error message is gone. Check all the cables and connections in the back of the COMAND or the DVD drive.
Why is my Mercedes navigation not working properly?
All the units which are part of the fiber optic need to be in proper working condition. If your Mercedes uses a separate drive for the NAVI DVD, it is possible that this unit can be defective. Learn more about fiber optic problem by reading Mercedes Audio System Explained. The DVD drive that holds your navigation disk could be damaged.
Is there a way to reset the navigation system?
On occasion, the navigation system may need to have a master reset performed. This task permanently deletes all data stored on the system and resets the preferences to the factory settings.
If you are trying to update the navigation system using an update DVD you may get an error message saying Loading Navigation. This process can take a while in some cases up to one hour. Try removing the Navi DVD, turn off your car and let it sit for one hour.
What to do if your Nav screen won’t open?
CAUTION: disconnecting the battery cable will reset the NAV, Radio and Hybrid systems (s). Do this at your own risk. Once reconnected – the nav screen “open” button worked and I was able to remove and re-insert the NAV disc. This solved my problem, but I had to re-enter my saved addresse and radio settings. HH Limited.
Why is there nothing to post error in Microsoft Dynamics NAV?
Here the Qty is 1 against which we are generating Invoice. But still both the orders are not posting from several users. Kindly update on this issue. Kindly share the solution, as our current Partner is unable to resolve the problem due to Protected Code written by previous Partner.
Are there modifications in your Microsoft Dynamics NAV forum community?
You will probably need to dig a little deeper, because the first layer is a “post (yes/no)” codeunit, containing the selection dialog and the codeunit which is really called for posting. Then have a look if this is the protected one. If not… are there modifications in your CU80?