Why does my bike stall when put into 1st gear?

So I recently replaced my clutch plates and fibres and finally had a chance to ride the bike. Upon start up, I let the bike warm up, held clutch in and then put the bike into gear, and it immediately jumped and stalled. It keeps doing it and I can’t ride the bike. The clutch has been bled properly with 0 bubbles.

What causes a motorcycle to stall at idle?

Or, you could have air leaking around the throttle, just enough to lean it out at idle; the mounting boots could be the leak, or diaphragms in the carbs, that kind of thing. Wow, thanks both of you! I will try these things when my mechanic manual comes for this bike, the owners manual is like “here is the start button, a durr.”

What to do when your motorcycle starts stalling?

Now option b) give it more choke, it goes back up to 1,500 rpm which is great and then 10 seconds later it starts sounding like its going to take off (4k rpm atleast) sometimes you can get it to idle at 1.5k for a minute or two, but then it will either start to die, or it will start revving too high.

What causes a ct200u ex minibike to stall?

If I wait about 30 seconds, it will start right up, run for 15 seconds, and repeats stall. Tried playing with choke, carb settings, to no avail. Starts, runs 15 seconds, then dies. First I thought it might be a clogged carburetor. Cleaned it (no go), then replaced it (same problem).

When do you Put your bike in 1st gear?

Remove ads, support ADV. Bike stalls immediately when put into 1st gear – clutch sticking? Discussion in ‘ Thumpers ‘ started by peteandrewd, Jun 23, 2016 . Hey everyone. So I recently replaced my clutch plates and fibres and finally had a chance to ride the bike.

What to do when your clutch stalls in first gear?

My friend used to have this problem, when he used to do cold starts hed fire his bike up then apply the back brake, hed then rev the engine grab the clutch and put it into gear, it would make a big clunk but then be fine for the rest of the day. This post is not being displayed . The clutch is sticking overnight, do you have the correct oil in it?

Is it safe to start a bike without the clutch?

If you ride off road you should know how to start and stop your bike without the clutch. It’s tricky but it can be done. Probably the safest way would be to get a rolling start in neutral jump on the bike start it and shift into gear. Almost like a push start. (You must log in or sign up to reply here.)

What’s the first gear on a Kawasaki Z900?

Bearing in mind the Z900 already has an engine tuned for good low-to-mid-range torque, the Z900RS initially feels quite aggressive in first gear, taking a little bit of wrist recalibration to adjust to the acceleration unleashed by a small turn. Even in third, it pulls enthusiastically from about 2,000rpm, making for a healthy muscle-bike feel.

Why does my Kawasaki z900rs keep shutting off?

When you try to hold a constant low throttle through a corner, there’s a tendency for it to shut off and then reopen with a jerk. It seems to be a common problem on late motorcycles, no doubt related to the challenge of meeting ever tightening emission limits. The Z900RS has a mild case of it, not half as bad as some others I could list.

When do I drop from first to neutral my bike stalls?

This post is not being displayed . When I initially start up the bike and drop from neutral to first, the engine stalls pretty much every time. It only happens once and then I can drop down to first with no problems during a ride.

Why does my Fazer stall when I put it in first gear?

I know on my Fazer, if the side stand is down and I go to put it into 1st gear from neutral, the engine will cut out. This is the switch working correctly. If it developed a fault it either wouldn’t cut the engine, or it would sense that the stand was down, even if it wasn’t.

Can you roll a bike in gear with the engine off?

Nope. Can’t roll it in gear with the engine off. It’s a wet clutch system. Always had to warm the bike up thoroughly to be able to push it when shut off. Basket was already checked for grooves and wear and is fine.

Can you push a bike around in gear?

Bike is a 2011 KTM 530 EXC. With the bike shut off can you push it around in gear with the clutch pulled in? I would pull the clutch and soak the fibers. With everything pulled out check the basket for grooves or damage. UK for now. I was having the same issue. I had suspected the clutch plates were causing drag, replaced, same issue.

What to do when your bike won’t go into first gear?

1. I didn’t have any B12 , but added SeaFoam Motor Treatment to the crank case. 2. Found, as suggested, that the bike wasn’t actually going into first gear, even though the neutral like would go off. 3. Utilized suggestion and put presssue on the gear lever while rolling the bike.

Why are the gears not working on my Kawasaki motorcycle?

Perhaps the clutch disks are stuck together and the clutch isn’t releasing; the shift lever may be moving but not quite far enough to engage first. Shut the motor off while you think it’s in first and try to push the bike in that state (without applying clutch lever). If it’s in first and everything is kosher the motor will fight your progress.

Why are the gears on my bike not shifting?

The gear refusing to shift is the most common problem with a very simple solution – indexing. When indexed properly, the gears shift one after the other with ease. If you are skipping gears and facing problems, the indexing is to blame.

Can you shift from neutral to 1st gear?

If you don’t want to pull the plates you could lay the bike on the clutch side and I think that the oil would pool in the clutch area and maybe soak your plates. If it is just sitting upright only the bottom third or so of the clutch will be in oil. Can you shift from neutral into gear give the bike some gas and take off?

Why does my Honda ATV not shift gears?

The problem occurs even more often when it is cold outside. Fortunately, the answer/fix to the problem is really very easy! The problem is caused by very heavy, stiff, gummy grease that was installed in the shift motor gears at the factory. Once that grease is removed and replaced with a different grease, you’ll be back to shifting normally!

How do you change the shift motor on a Honda ATV?

Once that grease is removed and replaced with a different grease, you’ll be back to shifting normally! So, here’s how you replace that grease: Remove the shift motor and gears (all one piece) from the lower front of your engine.

Why does my Honda ATV stall in cold weather?

During the last few months (50-60 miles of use) the ATV has acted up on TWO occasions in relatively cold weather 15 degrees (F). The ATV will be running fine, but when I slow down to idle speed and then try to accelerate the engine will bog out/stall. Note: the ATV will idle just fine, but when throttle is applied it simply dies.

What causes a motorcycle to stall when the clutch is released?

Please try again later. This is a detailed description of a classic motorcycle problem, characterized by an engine stall when the transmission is in gear and the clutch handle released. The ignition wiring diagram is shown for a Kawasaki VN800 motorcycle, but many bikes with sidestands will have similar variations.

What does it mean when your motorcycle is bogging?

Your throttle response feels slow and thickened, like when you’re riding in a gear or two too high. Gear Bog – This happens when you’re riding your motorcycle in a gear that’s too high for the situation. The feeling is slow and sluggish like you’re riding through a mud bog.

How can I get my motorcycle to stop stalling?

Once you get to a good cruising speed and your rpm’s start to get high then pull in the clutch handle again and pull up on the gear selector to go to 2nd gear. Then slowly let go of the clutch handle. If you repeat this process you can successfully go through all the gears without stalling your motorcycle.

Why does my motorcycle stall at high RPM?

As you slowly increase the throttle and slowly let go of the clutch handle the motorcycle will start to roll forward. Once you get to a good cruising speed and your rpm’s start to get high then pull in the clutch handle again and pull up on the gear selector to go to 2nd gear.

Why does my motorcycle spin when I drop into first gear?

When you pull the clutch handle and drop the motorcycle into first gear the engine is still spinning independently of the transmission because the clutch has disengaged the two. As soon as you start to let go of the clutch handle the transmission and the engine start engaging, and they want to spin together.

What to do if your car stalls when you put it in gear?

Basically, the first is to apply your foot brake after steering over to the roadside. Don’t forget to turn the hazard light on and try restarting your vehicle. If it cannot restart your car, you should call a mechanic or your friends to help. Aside from that, the jumper cables do not work in rebooting the engine, right?

Why does my bike stall when put in first gear?

Assuming the clutch is adjusted correctly with the right ammount of free play, stalling when selecting first gear from cold is usually a case of sticking clutch plates. This invariably happens with my YamahaXJ600.

What to do when put in first gear?

10 min job there will be a sump bolt on the bottom of the gear box dont forget let the bike drain standing upright then lean it one way for 5 mins then the other for another for 5 makes sure all old oil out, dont forget to put the sump bolt back in before toping up done that before mess ewverywere.

Navigation