Why are my wipers not working on my Yukon Denali?
My wipers were working intermittently. I replaced the motor control board (actually the whole motor and control board, as this is the only way it comes for a 2011 Yukon Denali) Two weeks later and I have the exact same problem. Wipers would not work at all last night, worked this morning.
Why are my windshield wipers not working on my car?
The windshield wipers may not work intermittently due to a faulty wiper motor control board. Our technicians tell us that lightly taping on the wiper motor when the fault occurs should temporarily get the wipers working again. Some vehicles were recalled for this problem and some were not.
Why do I hear a noise from my wiper motor?
You can hear a noise from the wiper motor area like it is trying to work, but will not. Moving the wires into the wiper motor control board sometimes will get them working, but only for a short time.
My wipers were working intermittently. I replaced the motor control board (actually the whole motor and control board, as this is the only way it comes for a 2011 Yukon Denali) Two weeks later and I have the exact same problem. Wipers would not work at all last night, worked this morning.
Are there any windshield wipers that will work?
Wipers will only work on the high speed setting. Low or delay setting will not work. I don’t have a Denali, but an 04 GMC Yukon. Windshield wipers work on highest setting but nothing else. Also can’t use the cleaning function. Wiper blades working fine one day and very next very very very slow moving. My wipers were working intermittently.
Why are the wipers on my car not working?
Torn wiper blades, a bad wiper motor, a blown fuse, or heavy snow may be why your wipers are not working. Keeping your windshield clear is paramount to a safe driving experience.
Why does my windshield wiper not work when I change the pivot?
A nut tightens onto the pivot stud to hold the wiper arm tightly to the pivot. If the nut is a little loose – which is common – the wiper motor will turn the pivot but the wiper arm will not move. You may see it slightly move when the wiper direction changes, but it does not wipe the windshield.
What does it mean when your windshield wipers don’t work?
You may see it slightly move when the wiper direction changes, but it does not wipe the windshield. You may notice only one wiper working while the other stays at the bottom. If you have this issue, make sure the wiper pivot nuts are tight.
What happens if there is no power to the wiper?
If there is power, the motor is bad. If there is no power, although the motor could “still” be bad, you first want to trace the circuit back to the power source to figure out where the break is. Once the circuit is fixed, of course if the motor still doesn’t work, it’s condemned and replaced.
What are the codes for my windshield wipers?
The codes P0300 and P0301 are coming up for a misfire on cylinder number 1. Check the cylinder for spark, fuel, and air. Check the spark plug and make sure that it is firing. The spark plug wire could have…
Do you need a snow brush for your windshield wipers?
Windshield wipers are able to remove small amounts of snow from your windshield, but heavy, wet snow needs to be cleared by a snow brush before operating your wipers. Wet snow can be so heavy on your wipers that your blades can get bent, the wiper arms can skip or strip at the pivots,…
You can hear a noise from the wiper motor area like it is trying to work, but will not. Moving the wires into the wiper motor control board sometimes will get them working, but only for a short time.
Wipers will only work on the high speed setting. Low or delay setting will not work. I don’t have a Denali, but an 04 GMC Yukon. Windshield wipers work on highest setting but nothing else. Also can’t use the cleaning function. Wiper blades working fine one day and very next very very very slow moving. My wipers were working intermittently.
Why does my GMC Denali suddenly stop working?
I have a 2007 GMC Denali with the same symptoms. The power suddenly dies. This is a reoccurring issue for the past 3 years. I noticed the negative battery cable had bad contact so I took a steel brush and scuffed up the cable where it meets the ground connection. That seemed to fix the issues for 6 months, but it came back again.
Where is the fuse box located on a GMC Yukon?
The fuse block access door is on the driver’s side edge of the instrument panel. The center instrument panel utility block is located underneath the instrument panel, to the left of the steering column. The underhood fuse/relay center is located in the rear of the engine compartment near the brake fluid reservoir.