Where is the service check light code on a Honda?
1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on. 3. MIL will indicate DTC’s by outputting a number of flashes.
What is the DTC code on a Honda Accord?
MIL will indicate DTC’s by outputting a number of flashes. Remember, these are manufacturer specific codes only. Refer to our Generic OBD II code list for definitions on all other Honda diagnostic trouble codes. Manufacturer Specific Codes P1106BARO Circuit Range/Performance Malfunction P1107BARO Circuit Low Input P1108BARO Circuit High Input
Where can I find the OBD code for my Acura?
If there is no procedure for your manufacturer specific code, then I suggest referring to a similar generic OBD II code (these are listed numerically by system type) to get a good idea of what to look for. If at this point you still need assistance use the “Get Help” link and let us know how we can help.
What to do if your Honda code is not working?
A guide on how to check your codes: If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.
How do you find the Diagnostic Code on a Honda OBD?
Turn ignition switch to ON position. Diagnostic Trouble Codes (DTCs) will be indicated by a series of long and short flashes on the Malfunction Indicator Lamp (MIL). The number of long flashes indicates the number in the 10s column. The number of short flashes indicates the number in the 1s column.
1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on. 3. MIL will indicate DTC’s by outputting a number of flashes.
How to test a Honda Civic a / C unit?
Open the globe box. Remove the glove box stop on each side, then let the glove box hang down. 4. Insert a thermometer in the dash center vent. 5. Place another thermometer (B) near the blower unit’s recirculation inlet duct. 6. Test conditions: •Avoid direct sunlight. •Open hood. •Open front doors. •Set the fan switch to highest speed.
Where can I find the Check Engine Light code?
You may also retrieve Honda check engine light codes using the Malfunction Indicator Lamp (MIL), by counting the flashes as follows: 1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash.
What’s the air pressure in a Honda Civic?
Ambient temp Humidity % Inlet air temp Static system pressure 45 psi minimum Center vent temp ~30°F < ambient Low side pressure Typical: ~ 30 psi High side pres- sure Typical: 2.2 to 2.5 X ambient °F Pressure behavior when AC is shut off: High Side Pressure PSI Low Side Pressure PSI Center Vent Air Temperature °F Inlet Air Temperature °F 1.
Where is the warning light on the fuel gauge?
As I was leaving I immediately noticed that the fuel gauge needle is all the way to the bottom and the orange warning light is flashing just below the indicator. I tried the simple things like disconnecting the battery for 10 minutes but it did not help.
How to self diagnostic a Honda Civic a / C?
The HVAC control unit has a self-diagnostic function for heating, ventilation, and air conditioning system. To run the self-diagnostic function, do the following: 1. Turn the ignition switch OFF. 2. Press and hold the recirculation control and rear window defogger buttons, and turn the ignition switch ON (II).
What is the chassis code for a Honda Civic?
In the years from 2006 to 2015 Honda released its 8th & 9th Generation Civic. 9th Gen Chassis Codes: FB2, FB4, FB6, FG 3, FG4. 8th Gen Chassis Codes: FG1, FG2, FA1, FA3. In the years from 2001 to 2005 Honda released it’s 7th Generation Civic.
Why is my Honda Civic a / C not working?
Clogged condenser or radiator fi ns A/C condenser or radiator fan not work- ing properly Clean. Check voltage and fan rpm. Check fan direction. Line to A/C condenser is excessively hot. Restricted fl ow of refrigerant in system Restricted lines. Discharge pressure abnormally low Excessive bubbles in sight glass; A/C condenser is not hot.