Where is the fuel pump relay located on a car?

The fuel pump relay is an electronic component that is found on virtually all vehicles equipped with an internal combustion engine. It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by…

Is the fuel pump relay controlled by the PCM?

Consequently, the fuel pump relay is usually controlled by, the ignition or powertrain control module (PCM). As a result, when switched on, the fuel pump relay; will provide current to the fuel pump, so that it may function. Therefore, any faults with it, can cause fuel pump issues.

Where is the fuel pump control module located?

It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by the ignition or Powertrain Control Module, and when switched on, will provide current to the fuel pump so that it may function.

What to do if your fuel pump relay is overheating?

Pull out the relay and visually inspect the terminals and socket; for signs of corrosion and overheating. Consequently, Corrosion prevents proper current flow; and overheating indicates problems with the relay or circuits it connects to. Clean corroded terminals and socket with electrical contact cleaner. Next Check all fuses before any repairs.

What happens when a fuel pump relay goes bad?

Consequently, if the fuel pump relay has an issue, it will cut off power to the fuel pump. Also, if a relay overheats, the electrical contacts inside the relay can short circuit; causing the electrical flow to stop. However, when the relay contacts cool, it will resume the flow of electricity.

Which is the secondary side of the fuel pump relay?

Terminals 87 and 30 are the secondary side of the relay. Consequently, It acts as the “switch” that connects electrical current, from one terminal to the other. Use Jumper wires to supply 12v power to terminals 86 and 85. Next, use a test light on terminals 87 and 30, to see if you have power.

What should I do if my fuel pump is not working?

Use Jumper wires to supply 12v power to terminals 86 and 85. Next, use a test light on terminals 87 and 30, to see if you have power. Finally, if the test light goes on the the problem lies somewhere else. Fuel Pump Circuit Breaker Reset

Where is the fuse block on a GMC Safari?

The fuse block is on the lower portion of the instrument panel on the driver’s side. Courtesy Lamps, Glove Box Lamp, Dome Reading Lamps, Vanity Mirror Lamps, Courtesy Lamps

Where to check for no start fuel pump?

The first thing you want to do is check the fuse panel to see if the fuse is blown. If your car has two fuse panels than the one in the engine compartment; should be the correct one to check. The fuse panel or circuit box is usually located near the battery; and is a small black box with a removable lid.

What causes a GMC fuel pump to fail?

When the level of fuel in the tank is below ¼ it causes the pump to run hot and driving regularly in this condition can lead to early pump failure. A defective GMC fuel pump can affect the performance of the vehicle and even bring it to a standstill.

What causes a fuel pump fuse to blow?

When the fuel pump begins to fail it overheats, causing it to drain more amperage (amp); if the amps exceed the amount of amps the ECM 1 fuse allows, the fuse will blow. Replacing the fuel pump should correct this problem. The ECM 1 operates via voltage sent from the battery.

What to do if your fuel pump does not work?

Keep the accelerator pedal fully pressed while cranking the engine to bleed the system. If this does not work, then it could be that the fuel filter will need to be bled. This can be done by powering up the fuel pump fuse. To do this, locate the small holder in the cover on the right side of the firewall.

Where is the fuel pump on a GMC Yukon?

When the straps are removed the rear of the tank will drop down to the ground. When the fuel lines are disconnected, the tank should be slid back and the front will drop. The fuel pump can now be accessed. How to connect the wires of the GMC fuel pump/sender on a 2003 Yukon?

What happens if the fuel pump relay fails?

If you hear no humming from the fuel pump but the car eventually starts and runs fine, then the fuel pump relay has failed. If the fuel pump relay fails, the engine management system records this event. A fuel pressure sensor lets the computer know if the fuel pressure has not created any pressure during cranking operation.

Is there no power to the fuel pump?

No power to the fuel pump and the fuel relay is not getti… Q: No power to the fuel pump and the fuel relay is not getting power. My car has 190000 miles.

Do you need to replace fuel filter when replacing fuel pump?

The fuel level sensor is a separate component attached to the fuel pump. This part does not always come with the fuel pump and sometimes is not interchangeable with aftermarket fuel pumps. Chevrolets have a common issue with fuel filters getting clogged. You always want to replace the fuel filter when replacing the fuel pump.

What to do if your fuel pump relay stops working?

Connect one lead to one of the power circuit pins, and connect the other lead to the other power terminal. If you hear a beeping sound, your fuel pump relay’s power pins have shorted. Replace the relay. You can test the fuel pump relay, along with many other parts in your car, with the cheap and handy multimeter. (Photo Source: carcody)

Why does my fuel pump not start when I change it?

You always want to replace the fuel filter when replacing the fuel pump. This could cause the concern you are having. It may seem as you are getting enough fuel from the pressure regulator but if the pressure from the fuel tank is not correct, it will still not start. Another problem you could be having is spark.

How much does it cost to replace a fuel pump relay?

You can easily find fuel pump relays online or at any automotive spare parts shop.The average replacement cost of the fuel pump relay ranges from $90 to $150, of which $20-$50 is for parts and the remaining is the labour cost.

What are the symptoms of a bad fuel pump relay?

A bad fuel pump relay can cause many different symptoms. Here are the most common ones The fuel pump relay is an important component of the fuel system of your vehicle. The fuel pump relay gives the fuel pump power when it is time to build up fuel pressure in the rail.

Fuel pump relay Replacement cost. The average replacement cost of the fuel pump relay is around $90 and $150. The parts may cost you between $20 and $50, while the remaining cost is the labour cost. Fuel pump relay is a small electronic device which is easily acquired online or at the nearest spare parts shop.

What is the average rating of a fuel pump relay?

Average rating from 198 customers who received a Car is stalling Inspection. The fuel pump relay is an electronic component that is found on virtually all vehicles equipped with an internal combustion engine.

What are the symptoms of a bad fuel pump?

The engine may still crank when the key is turned, however it will not be able to start due to lack of fuel. This symptom can also be caused by a wide variety of other issues, so having the vehicle properly diagnosed is highly recommended. 3. No noise from the fuel pump

When do you need to replace the fuel pump relay?

If the engine is stalling or not starting, or the fuel pump is not making any noise when the key is on, you may need to replace the fuel pump relay. 1. Engine stalls 2. Engine does not start 3. No noise from the fuel pump

Where is the fuel filter and pump located?

Raise the car (740) high enough, so that you have the best of angles (and room to work) to hold all in proper position. Spray the fuel filter fittings with penetrating oil. The filter and pump sit in a subframe or cradle under the driver’s side of the car, mid-ship, held up by three 10mm bolts.

What to do when no fuel is left in the fuel pump?

Pull the fuel pump fuse while engine is running, engine stops with no fuel pressure left in line. (alternative 1:pull the fuses for the fuel pumps and crank the engine. (alternative 2: attach a vacuum pump to the FPR vacuum fitting and apply vacuum.)

What are the symptoms of a faulty fuel pump relay?

1 Engine does not start. A common symptom of a faulty fuel pump relay is an engine that just refuses to start, even though the engine may still crank when the 2 Engine stalls. One of the most common symptoms of a failing fuel pump relay is an engine that suddenly stalls. 3 Loss of Power. 4 No noise from the fuel pump. …

When is the fuel pump relay turned on?

The fuel pump relay is activated whenever the ignition is turned on. A fuel pump relay functions primarily to maintain a consistent voltage supply to the fuel pump. The ignition or powertrain control module (PCM) usually controls the fuel pump relay.

Where is the fuel pump reset switch location on the Chevy?

The fuel pump reset is snugly positioned in the passenger footwell. If the switch needs to be replaced, You can expect to pay between $30 and $138 for parts. The fuel pump reset switch can be found on the toe-board, to the right of the transmission hump, in the passenger-side footwell.

Where is the fuel pump in a car?

The fuel pump is located in the fuel tank, near the rear of the vehicle and can usually be heard when the engine starts. A healthy fuel pump plus a healthy fuel pump relay will often produce a variation of a low volume hum or whine which can be heard from inside the vehicle, or from the outside, near the fuel tank.

How do you clean a fuel pump relay?

Since any debris will affect the fuel pump relay’s performance, you should regularly inspect and clean it when necessary. The fuel pump relay is an electrical car part, thus be extremely careful when handling a relay. First, take off the relay and use the blower to blow off dirt and dust for about 1-2 minutes.

What does the main relay on a Honda do?

The main relay in a vehicle controls the fuel pump and supplies power to the injectors. Knowing how to test a Honda main relay can help you better pinpoint the cause when an electrical issue arises. There’s a pretty simple way to tell if your main relay is affected. Simply turn on the vehicle and see if it continues to run.

How does a fuel pump relay work in a car?

It is usually controlled by the ignition or the power control module. When you turn on the ignition, the fuel pump relay is activated and will supply electricity to turn on the fuel pump.

The fuel pump relay is located in your under hood fuse panel on the drivers side. It is the number in the 32 position in the picture of the fuse box itself. Ron

Where is the fuel pump fuse box located?

The engine’s or the dashboard fuse box is usually a long black box containing a fuel pump relay and various other fuses and relays. For different vehicles, the fuel pump relays can be located in different places.

Where is the FP relay on a car?

The FP Relay is in the intelligent power distribution module in the right front engine compartment. Check fuse no.32 15amp in the IPDM Do this find the fuel pump connector and power the black and yellow wire from the battery this will cause the fuel pump to come on.

Where is the fuel pump relay located on a Ford F150?

The fuel pump relay of a Ford pickup, also known as the fuel shut off switch, is located in the passenger foot well, behind the behind the kick panel and inside the fuse panel.

What is a fuel relay fuse?

A fuel pump relay is an electrical device much like an automotive fuse. It directs current to the electric fuel pump and ensures that the part receives enough power to operate properly, but not too much as to damage it.

What is a fuel relay?

A fuel pump relay or any kind of relay is an effective way to utilize a small degree of voltage to generate a signal in order to open or close the contact of a higher current or voltage line. The relay basically functions as a switch.

How often should I change the fuel pump relay?

Repeat at least 5 times; the recommended number can vary, depending on the vehicle. You can test the fuel pump relay by swapping it with a similar one in the fuse box. The air conditioner relay is often close enough. If the car starts with the second relay connected, the fuel pump relay is bad.

Where is the fuel pump relay its located?

In most vehicles, the fuel pump relay can be located in the fuse box in the engine bay. The fuse box of the engine is usually a long black box which contains a fuel pump relay along with various other fuses and relays.

Where is the fuel pump relay located in a vehicle?

Most fuel-pump relay units are located under the dashboard near the steering column. In some cases, the unit is located in the area where the steering column is mounted or near the engine’s firewall.

Were is the fuel pump relay switch located?

Location The fuel pump relay of a Ford pickup, also known as the fuel shut off switch, is located in the passenger foot well, behind the behind the kick panel and inside the fuse panel .

Where is a fuel pump located?

In many modern cars the fuel pump is usually electric and located inside the fuel tank. The pump creates positive pressure in the fuel lines, pushing the gasoline to the engine. The higher gasoline pressure raises the boiling point.

Why does the fuel pump relay need to be Tip Top?

The fuel pump relay needs to function in tip-top condition if the engine is expected to run without any issues. Therefore, any compromise in the fuel pump relay can directly cause engine problems, such as the stalling of the engine.

Where can I buy a fuel pump relay?

At O’Reilly Auto Parts, we offer high-quality fuel pump relays. Check out our stock of fuel pump relays to find the part you need for your repair.

Why does my Ford pickup have a green relay?

You’ll be able to find out if the fuel pump relay, or the fuel pump Inertia Switch, or the fuel pump is the cause of the No Start Condition on your Ford car or pickup. If your fuel injected Ford pickup, van, or car still has the Ford relay, this bad boy will be a green color (like the one in the image viewer).

What kind of noise does a fuel pump make?

No noise from the fuel pump. Another symptom that may hint at an issue with the fuel pump relay is no noise from the fuel pump when the key is switched on. Most fuel pumps will produce a low volume hum or whine which can be heard from the inside the vehicle if listened for closely, or from the outside of the vehicle, near the fuel tank.

How to test and replace a fuel pump relay?

How to test and replace a fuel pump relay. The principles shown here apply to most vehicles. However, it’s best to check with your vehicle’s repair manual for testing parameters.This specific vehicle is a ’97 Nissan Maxima. — Choosing the best oil filter: Wix XP / Amsoil / Royal Purple..

How does the fuel system work in a Honda Civic?

The fuel system in your Honda Accord and Civic consists of many working parts. Each part is designed to work in sync with your car’s entire fuel system to deliver optimum fuel flow to the engine, and sustain the normal operation of your vehicle’s idling, acceleration, and speed.

What should I do if my Honda fuel line is dirty?

Clean or replace the dirty fuel injectors, and check the fuel line pressure using a fuel pressure gauge. Visit a local mechanic to have the fuel pressure regulator replaced if it’s operating without sufficient pressure.

What to do if your fuel pump is bad?

If your car has a bad fuel pump check valve, the biggest issues you’ll notice are your car will run poorly, stall, or it won’t start at all. Replace the fuel pump check valve with one that meets the specifications of your vehicle. You will need to refer to the owner’s manual.

How many amps are in the Honda Element?

Passenger compartment No. Amps. Circuits Protected 16 — Not Used 17 15 A Fuel Pump 18 15 A Front Accessory Power Socket 19 7.5 A Turn Signal Lights

When did the Honda Element come out for sale?

The compact crossover SUV Honda Element was produced from 2003 to 2010. In this article, you will find fuse box diagrams of Honda Element 2003, 2004, 2005, 2006, 2007, 2008, 2009 and 2010, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout).

What causes bad fuel economy in a Honda?

Poor fuel economy can be exacerbated by a loose gas cap, clogged fuel filters and fuel lines, or clogged injectors. Check for trouble codes in your car to diagnose a faulty fuel system.

What kind of fuel pump does a 2002 Honda Civic have?

The 2002 Honda Civic came standard with a 110-horsepower, 1.7-liter engine and had a series of optional engines capped by the 160-horsepower, 2.0-liter four-cylinder engine. The fuel pump relay on the 2002 Civic is referred to as the PGM-FI relay and it also acts as the main relay for the vehicle.

Where are the fuses on a Honda Accord?

Passenger’s Under-Dash Fuse Box Number Fuse name Circuits Protected 6 LAF HEATER Primary H02S relay (ULEV) 7 P/W REAR L SUNROOF RELAY Left rear window motor, Moonroof open an 8 P/W FRONT R Front passenger’s window motor 9 RADIO CIGARETTE LIGHTER Accessory power socket, Audio unit

What to do if your Honda fuel relay isn’t working?

If playback doesn’t begin shortly, try restarting your device. Setting a goal at the Nürburgring | Does it Matter? EP 1 Here at the midnight garage you can expect a lot of random car shenanigans, mostly with JDM imports.

Where is the battery negative terminal on Honda main relay?

Consult your owner’s manual or vehicle repair manual and remove the main relay. Attach the battery positive terminal to the No. 4 terminal and the battery negative terminal to the No. 8 terminal of the main relay.

How to test a fuel pump relay with a multimeter?

1 Turn off your vehicle and remove the key from the ignition. 2 Find the fuel pump relay in your vehicle’s fuse box. 3 Pull the relay straight out from the fuse box to remove it. 4 Clean the relay prongs with a wire brush. The fuel pump relay may be faulty or have a loose connection if it’s developed any rust or corrosion on the …

Where is the fuse box for the fuel pump?

The main fuse box is usually located underneath the hood near the front of your vehicle, but there may be a smaller fuse box under the steering column inside your vehicle as well. Pull the cover off of the fuse box and look at the diagram printed on it to know where the fuel pump relay is located.

Where is the fuel pump relay located in a car?

You can try to listen closer around the fuel tank for any noise for 2-3 seconds after turning the ignition on. Where is the Fuel Pump Relay Located? In most car models, the fuel pump relay is located in a fuse box somewhere under your dashboard, but it can also be located in the fuse box in the engine bay.

How to check fuel delivery in Hyundai Sonata?

Check fuel delivery in the Hyundai Sonata if the engine runs rough, stalls in traffic or doesn’t start at all. Relieve fuel system pressure. Take the back seat cushion out and remove the access panel underneath to disconnect the connector for the fuel pump module.

What kind of engine does Hyundai Sonata have?

185-horsepower 2.4L I4 6-speed shiftable automatic FWD Scanned and found code P107500 Camshaft position actuator relay circuit performance fault in active state. Vehicle was idling high.

Are there any recalls on the Hyundai Sonata?

Chart based on 2175 repairs. See TSBs and recalls for the Hyundai Sonata. Worried about potential repair costs? An extended warranty can provide peace of mind. Chart based on 363 repair trips. The repair cost chart excludes repairs made under warranty, do-it-yourself repairs, and repair trips that include maintenance.

What causes low power light on Hyundai Sonata?

The camshaft timing sensor cover seal was breached due to sub zero temperatures and oil leaked on the sensor. This caused a low power condition and check engine light. There was a backorder for the part.

Where are the fuses on a Jaguar XJ6?

If your car’s accessories are shutting off on their own inspect the car’s fuses and replace blown ones. Replacing a fuse is much cheaper than paying for new equipment or repairs that you don’t need so take a few minutes to find your fuse boxes. Your owner’s manual can help you locate them. Jaguar XJ6 Series 3 1. Glass fuse https://amzn.to/2GeEANS

It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by the ignition or Powertrain Control Module , and when switched on, will provide current to the fuel pump so that it may function.

How to replace fuel pump on Jaguar X type?

The fuel pump on a Jaguar X type, is a Very difficult job, however if you cut 2 holes the job becomes super easy. Watch this The fuel pump on a Jaguar X type, is a Very difficult job, however if you cut 2 holes the job becomes super easy. Watch this Skip navigation Sign in Search Loading… We’ll stop supporting this browser soon.

What are the relays on a Jaguar S-type?

Diesel – Engine management system relay (2004) 2006-2008: Heated Exhaust Gas Oxygen sensors, ignition EMS relays. Diesel/petrol – EMS relays, Supercharger water pump relay. 2004-2005: Petrol – Ignition coil on plugs supply, capacitor, HEGO Relay coil.

What to do when your fuel pump goes out?

Step 1: Turn on the ignition key to run. Listen for the fuel pump to actuate. Also, listen to the fuel pump relay for any buzzing or clicking noise. Step 2: Start the engine. Check that there is oil pressure. On some vehicles, there will only be an oil light indicator. When the indicator light goes out, then there is oil pressure.

What are the symptoms of a fuel pump relay problem?

1. Engine stalls One of the first symptoms of an issue with the fuel pump relay is an engine that suddenly stalls. If the fuel pump relay has an issue while the vehicle is operating it will cut off power to the fuel pump, which will cause the engine to stall.

What causes a fuel pump to stop working?

However, this can happen due to several other reasons, such as a choked fuel filter, so you should always properly diagnose your car before replacing any parts. If the fuel pump relay may have any bad solderings inside it, it might suddenly lose the relay connection and stop delivering power to the fuel pump.

If the fuel pump relay fails, the fuel pump will receive no power and will not operate, thus it will be silent. Always start with a visual inspection first before moving on to other tests, which will be specified below.

How to repair the fuel pump relay in a 1983 280 SL?

This video shows how to locate and repair the fuel pump relay in a 1983 280 SL. The video also touches on the fuel pump relays and fuses in earlier SL’s incl… This video shows how to locate and repair the fuel pump relay in a 1983 280 SL. The video also touches on the fuel pump relays and fuses in earlier SL’s incl…

How many pins does a fuel pump relay have?

Generally there are four pins (terminals) on the fuel pump relay. One is for input voltage, one is the ground pin, one is the load pin that goes to the fuel pump, and one goes to the battery.

Symptoms of Bad Pump Relay Fuel Pumps: Fuel Pump Noise Fuel Pre-Pump Problems & Diagnoses Fuel Pump and Sender Replacement Fuel Gauge Failure: Fuel Level Sending Unit Repair Fuel Main Pump Problems & Replacement Gas More Than Empty But Can’t Be Pumped Out B230K BiFuel Engine Ticking Sound: Fuel Pump Fuel Tank: Gas Cap

Where is the fuel pump shut off switch located?

On Ford, Peugeot, VW, Citroen, Vauxhall, Subaru, Renault, Toyota and Mazda, inertia switch location is usually on one of the following two hidden places: Behind or below glove compartment, sometimes hidden under the carpet; On the driver side, between the footrest area and door, sometimes hidden under the carpet.

What causes a Ford fuel pump to shut off?

If your Ford ever fails to start or stalls on you suddenly, the first thing to check is the inertia fuel shut-off switch. The switch is designed to trip and cut power to the fuel pump in the event of a collision, but you can also trigger it by hitting a large bump or pothole as well.

Is there a way to reset the Ford fuel shut off?

To reset your Ford’s inertia switch, press down on the reset button. Although the location of the shut-off switch varies by year and model, Ford has stuck with a few common spots over the years.

Usually, when you start your car the fuel pump gives off a slight buzzing sound signaling that it has started working. However, if there is any problem with the fuel pump relay the fuel pump will not respond at all and you will be left turning the ignition key again and again. If you experience such an ordeal, it is time to visit the mechanic.

How much should it cost to replace a fuel pump relay?

A fuel pump relay will typically cost about $25 for the part, and a mechanic may charge a minimum of an hour’s worth of labor to replace it. The vehicle not starting may be a fuel pump or relay along with other possible ignition problems.

Is there a relay switch for the fuel pump?

In addition to controlling the flow of fuel to the engine, the relay also keeps the electric fuel pump from functioning after a collision, minimizing the chance of fire igniting after an accident. After a collision, the fuel pump relay switch is automatically activated, preventing the vehicle from cranking.

Where specifically is the fuel pump relay?

In most vehicles, the fuel pump relay can often be found in the fuse box in the engine bay, which is usually a long black box which contains fuel pump relay along with various other fuses and relays. The fuel pump relay can be found in most engine bays. (Photo Source: pinterest)

What is the purpose of a fuel injection relay?

Two relays are located inside the fuel-injection system; one of them is responsible for turning the ignition on without turning over the engine, and the other is responsible for turning on when the engine turns. You can check to see if the first relay is working by touching it while turning the ignition on and off.

How do you check the fuse on a Nissan Altima?

Open the fuse box cover. On the fuse diagram, find the number of the fuse you want to check. The diagram tells you where to locate the fuse on the panel. Pinch the fuse perpendicularly with the fuse puller and pull it out. To check a fuse, look at the silver-colored band inside the fuse.

Why is my fuel pump relay outside the fuse box?

If it’s located inside the engine bay, which can get hot from the engine’s heat, the heat can impede the relay’s performance. In addition, in the rare cases where you will find the relay placed in the engine bay but outside the fuse box, it will be exposed to heat plus dust and dirt.

What to do if your fuel pump is not working?

If no sound is coming from your fuel pump, it’s time to inspect the pump relay or fuse to see if it’s providing any power to the pump. At O’Reilly Auto Parts, we offer high-quality fuel pump relays. Check out our stock of fuel pump relays to find the part you need for your repair.

Where do you find the fuel pump relay?

When you shut off the ignition, it powers down the fuel pump. In most vehicles, the fuel pump relay can often be found in the fuse box in the engine bay, which is usually a long black box which contains fuel pump relay along with various other fuses and relays.

What are the symptoms of a bad fuel pump in a Pontiac Sunfire?

Here are the most common symptoms of a bad fuel pump in your Pontiac Sunfire: One of the most common signs that a fuel pump is going bad is a whining sound. The whining sound can indicate that the fuel pump is going out before there are any performance based issues. Keeping an open ear can save you from getting stuck somewhere with a bad fuel pump.

How does a fuel pump relay control the fuel pump?

The fuel pump relay is usually controlled by the ignition or Powertrain Control Module, and when switched on, will provide current to the fuel pump so that it may function. As the fuel pump relay controls power to the fuel pump, any faults with it can cause issues with the fuel pump,…

Where is the fuse box located on a Saturn L?

Saturn L-Series – fuse box – instrument panel (driver’s side) The passenger’s side fuse block is located under the instrument panel on the passenger’s right side.

Can a broken fuse be replaced with a new fuse?

Never replace a broken fuse with anything other than a new fuse. Even after a fuse is replaced, it will continue to blow if the cause of the overload is not identified and corrected. If the fuse continues to blow, have the vehicle’s electrical system checked by your dealer or a qualified service technician.

Where is the fuse box on a Dodge Ram?

The fuse panel is located behind the cover on the driver’s side of the instrument panel. The fuse box is near the battery.

Where are the fuses located on a Saturn L?

Saturn L-Series (1999 – 2004) – fuses box diagram Year of production: 1999, 2000, 2001, 2002, 2003, 2004 Floor Console Fuse Block The driver’s side instrument panel is located under the instrument panel on the driver’s left side. Saturn L-Series – fuse box – instrument panel (driver’s side) Fuses Usage RADIO Audio, OnStar®, Rear Seat DVD (Option

Why are fuses silver on a Saturn Astra?

The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of damage caused by electrical problems. Look at the silver-colored band inside the fuse.

What kind of wiring do you need for a fuel pump?

At the wiring you need to find the 12v supply wire from the ECU to the fuel pump. Once that wire has been found cut that wire so that you now have half of that wiring running to the fuel pump, and the other half running to the factory ECU. Choosing a Relay The relayyou need should be a four-prong relay with at least 14-gauge wiring.

No power to the fuel pump and the fuel relay is not getti… Q: No power to the fuel pump and the fuel relay is not getting power. My car has 190000 miles.

How to test a Volvo V70 fuel pump?

Electrical testing: Remove the under hood fuse panel cover. Check the fuel pump fuse. On my vehicle (V70 base 1999) it was fuse 3 15 amp (red arrow). Electrical testing: Working in the left side of the wiper cowl, loosen the four T20 Torx screws (red arrows). Then remove the electrical compartment lid (inset).

Where is the fuse box on a Volkswagen Passat?

Fuses and relay Volkswagen Passat B5 For the Volkswagen Passat B5 (3B, 3C) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005 model year. Fuse box in passenger compartment. Fuse box location. The fuse panel is located behind the instrument cluster on the left side. fuse box diagram legend (1996-05/2002) F1

Navigation