Where are the needle bearings in a JAG?
All four corners of the flat plate under the differential (lower swingarm inner joints). There are holes in the plate for access to the zerk fittings. The needle bearings in the lower pivot joint of the rear hub carriers; the fittings are just inside the rear wheels at the bottom.
Do you need slip plates for Jaguar XJ S?
The Jaguar XJ-S Repair Operation Manual describes a check, but it assumes you have original tires with full tread. It also assumes you have “slip plates”, devices you set the front tires on so they can slide around and not bind the suspension travel.
Where are the Zerk fittings on a 1983 JAG?
The pre-1983 Jaguars also had zerk fittings on the tie rod ends, but the later cars were fitted with “improved” tie rod ends with no such fittings. The ball joint zerk fittings are designed with a relief system to prevent the grease gun from applying too much pressure. Under the fitting itself is a plastic washer that covers the relief hole.
What kind of fittings does a JAG have?
GREASE (ZERK) FITTINGS: Unlike the newer American “low-maintenance” cars, the Jag has zerk fittings all over the suspension. Periodically it should be gone over with the grease gun, but please be conservative.
All four corners of the flat plate under the differential (lower swingarm inner joints). There are holes in the plate for access to the zerk fittings. The needle bearings in the lower pivot joint of the rear hub carriers; the fittings are just inside the rear wheels at the bottom.
The pre-1983 Jaguars also had zerk fittings on the tie rod ends, but the later cars were fitted with “improved” tie rod ends with no such fittings. The ball joint zerk fittings are designed with a relief system to prevent the grease gun from applying too much pressure. Under the fitting itself is a plastic washer that covers the relief hole.
The Jaguar XJ-S Repair Operation Manual describes a check, but it assumes you have original tires with full tread. It also assumes you have “slip plates”, devices you set the front tires on so they can slide around and not bind the suspension travel.
GREASE (ZERK) FITTINGS: Unlike the newer American “low-maintenance” cars, the Jag has zerk fittings all over the suspension. Periodically it should be gone over with the grease gun, but please be conservative.
What kind of styling does the Jaguar X308 have?
The X308 kept much of the same exterior styling as its predecessor, carrying its rounded four-headlamp bonnet, low roofline, sloping tail, and wrap-around rear light clusters.
How tall should the front wheels be on a JAG?
Measure the height to the center of the front wheels. With any luck, they should be the same, but if they vary slightly determine the average. Subtract 6-3/8″ from this height. This gives you the correct height above the ground for the flat bottom of the cross member between the front wheels.
Where can I buy OEM Jaguar car parts?
Genuine OEM parts can be expensive, particularly when bought from local dealers and retailers, but shopping online can make a big difference in how much you pay for your parts. Parts Geek offers a great selection of Jaguar car parts online at low prices and with the added convenience of hassle-free shipping.
What makes a Jaguar S-type a JAG?
The company resurrected an old nameplate from the mid-1960s for this car and took many styling cues from the original S-Type and Mark II. That’s not to say the car is a retro design; it is a thoroughly modern, sleek-looking luxury car with heritage. What makes a Jag a Jag?
How tall is a 2000 Jaguar’s Type?
Exterior Length 191.3 ” Body width 71.6 ” Body height 55.7 ” Wheelbase 114.5 ” Ground clearance 5.8 ”
How to request new parts for a Jaguar?
Complete the Jaguar Parts Request Form: Can’t find the new or used Jaguar parts you need? Complete the Jaguar Parts Request Form: