Menu

Navigation

What size fuel line does a Craftsman chainsaw use?

Posted on by Arif Clayton

What size fuel line does a Craftsman chainsaw use?

1/4 inch
Fuel line, 1/4 inch inside diameter hose. Cut to fit if needed.

What size is chainsaw fuel line?

It uses 1/8id x 3/16od, though 1/4od can be used also but it is a little harder to get pulled through the hole. This is pretty much a standard size on a lot of chainsaws, string trimmers, leaf blowers and etc.

How long does a chainsaw fuel line last?

50,000 to 75,000
The fuel lines are made to last anywhere from 50,000 to 75,000. In most cases, the checking of the fuel injection lines is not part of the routine maintenance you will receive from a mechanic. If the fuel lines are leaking, it poses a fire hazard, which is why it is important to get them fixed when needed.

How do you put a new gas line on a chainsaw?

Instructions

  1. Drain the fuel tank. Wear work gloves to protect your hands.
  2. Remove the cylinder shield.
  3. Disconnect the spark plug wire and remove the air filter.
  4. Remove the fuel filter.
  5. Remove the carburetor.
  6. Remove the old fuel lines.
  7. Install the new fuel lines.
  8. Install the fuel filter.

How do you replace fuel lines on a craftsman chainsaw?

HOW DO YOU REPLACE FUEL LINES ON A CRAFTMAN CHAINSAW MODEL 358355160. The lines are usually a tight fit in the fuel tank. This prevents leaks. They must be pulled out of the tank (one at a time) then cut the new lines end in a “v” pattern, this will allow you to push the new line through the tank. Long needle nose pliers are needed too.

What is the proper oil gas mixture for craftsmans chainsaw?

While Craftsman recommends a gas-to-oil mixture of 32:1 up to a 40:1 mixture, other factors, such as air quality or elevation, may alter the required amount of oil for your engine. The Craftsman chainsaw runs at high speeds, often higher than 10,000 RPM, so it needs a higher-quality gasoline to keep the piston at the right operating temperatures.

How do you replace Poulan chainsaw fuel line?

Route the new fuel line to the carburetor. Cut the line to length with the cutters on the needle-nose pliers . Attach the line to the metal tube. Fill the fuel tank with fresh gas-oil fuel for 2-stroke engines and start the chainsaw. It may take a few pulls to prime the new line with fuel.

What size fuel line does a Craftsman chainsaw use?

Posted on by Arif Clayton

What size fuel line does a Craftsman chainsaw use?

Fuel Line (Small)- 9/64 (.

How are the fuel lines connected to the carburetor?

If you have 2, small fuel lines to the carburetor connect them and start the engine. Reversing the fuel lines will not prevent the engine from starting. If you have them connected backwards, the engine will start and die. Reverse them and you will be correct. The routing of the fuel lines vary from model to model.

Where do gas lines go on a Ryobi?

One line goes from the fuel tank to the carburetor. One line goes from the fuel tank to the primer bulb, from the primer bulb to the carburetor, and back to the fuel tank. Be careful to not put a fuel line too near a hot place on the engine. If the gas is overheated it will vapor lock and stop fuel flow.

Can you get a fuel and vacuum line diagram?

Gy6 engine fuel and vacuum diagram products and names mentioned are the property of their respective owners. 2014 taotao atm 50 fuel and vacuum line routing can i get a fuel and vacuum lines diagram for my 50cc 2014 tao tao motorcycles question. This information applies to most 50 and cc scooters.

Where do the fuel lines connect to on a craftsman 358?

The routing of the fuel lines vary from model to model. Keep in mind that the primer bulb circulates fuel from the tank, through the carburetor, and back into the fuel tank. One line goes from the fuel tank to the carburetor. One line goes from the fuel tank to the primer bulb, from the primer bulb to the carburetor, and back to the fuel tank.

What kind of fuel line connector do I Need?

Fuel Line Connectors for Yamaha Outboard Motors… Fuel Line Connector for Mercury Outboard Motors… Fuel Line Connector for Suzuki Outboard Motors, 3/8″ Barb… Fuel Line Connector for Nissan/Tohatsu Outboard…

Where does the fuel line go in a weed eater?

Pull out about 1″ of fuel line from the fuel cap opening and attach filter. Replace the line back into the tank just like that because you want the fuel filter/line to flop around inside the tank. Now that same line goes from the tank to the bottom connector on the carb.

What kind of fuel line does speedway use?

Avoid using rubber lines in your fuel system and route your lines as far away as possible from heat sources like exhaust. Aluminum fuel line works great on low pressure applications, or you can opt for Speedway’s blue and black high pressure fuel hose, or stainless steel braided hose.

How do you get fuel lines out of a line trimmer?

Pull the old fuel lines out of the tank. If necessary, use needle-nose pliers to grip the lines. If you can’t pull the lines out, cut the lines flush with the tank. The use a small screwdriver to push the rest of the lines into the tank. Tip the trimmer and shake any fuel line pieces out of the tank. PHOTO: Pull the fuel lines from the fuel tank.