What kind of transmission does a Freightliner have?
Freightliner Transmissions by Eaton and Detroit Drive the next generation of technology with the new Detroit 12-speed, direct- or over-drive automated manual transmission. It combines an automated clutch with a computer-controlled shift actuator to give you the power you need while optimizing fuel economy.
What kind of truck is a 2015 Freightliner Cascadia?
2015 Freightliner CASCADIA 125, , This is a 2015 Freightliner CASCADIA 125 RYDER CERTIFIED Tandem Axle Tractor –80000 GVW…. 2015 Freightliner CASCADIA 125, , This is a 2015 Freightliner CASCADIA 125 RYDER CERTIFIED Tandem Axle Tractor –80000 GVW…. Great running truck.
When to set FMI 7 in Freightliner Cascadia?
Conditions to Set Fault • FMI 7 is set when the set when engine torque is greater than 400 Nm, engine torque commanded is less than 0 for 0.3 seconds and the clutch position commanded is open for 1 second with the gear position confirmed in neutral.
How is clutch assembly on Freightliner Cascadia controlled?
The mechanical clutch assembly is controlled through the Electric Clutch Actuator (ECA) that is mounted on the clutch housing. The Hybrid Control Module (HCM) controls the ECA position and monitors several variables to determine if their is a slip concern in the clutch when it is in the closed position.
What’s the problem with a Freightliner automatic transmission?
They will at least run a week or two between breakdowns! The problem with the newer automatics is when you are going down hill they will hit coast mode and come out of gear so the engine will idle and save fuel. When you start up the hill, it’s late, and you lose 5-10 mph before it’s back in gear again.
I have an Eaton 10-speed autoshift transmission and a Detroit engine in my 2001 Freightliner. I am having problems with the transmission. Some times it will not downshift below the 6th gear. It happened 4 times when I was driving a 160 miles trip.
Why does Autoshift not go into any gears?
When i have the truck off and turn key to start position and try to shift gears i can hear the transmission shifting successfully, however once the engine is running it will not shift gears. There are no service lights or error codes being displayed.
Why does my Eaton Fuller not shift gears?
My eaton fuller autoshift suddenly will not go into any gears in my driveway, just shows down arrows and R or 2 (flashing) when I try to go into any gear. When i have the truck off and turn key to start position and try to shift gears i can hear the transmission shifting successfully, however once the engine is running it will not shift gears.
Why does my transmission shift hard from 1st to 2nd gear?
The fluid gets dirty over time and when it does, it causes plenty of troubles. Hard shifting is one of them. If the color is dark brown or burnt, changing it is likely to solve this issue. Dirty transmission fluid. (Photo Source: procarreviews)
Click to expand… Harder to back up, imo. Dont have the clutch to ride back into the dock. When you go to set up you don’t stop on a dime like you do a manual. Roll past your spot so you have to account for that. Which auto is it? Freightliners have two options today, a DT12 (or DT15) or an Eaton.
What kind of manual transmission does Eaton make?
Eaton offers fully synchronized and non-synchronized manual transmissions as well as automated manual transmissions across a full spectrum of applications. Original equipment manufacturers around the globe count on Eaton’s extensive experience in tailor-made solutions that enhance the overall vehicle efficiency, reliability, safety and drivability.
How does automatic transmission work in Freightliner Cascadia?
One is the transmission can turn on the engine brakes. That stops transmission from missing gears when pulling a hill. Also at stop lights and in parking lots. Another this the DT12 has is GPS location on the hills.
How to troubleshoot an Eaton ultrashift plus fault code?
When troubleshooting an Inactive fault code, use the Fault Isolation Procedures to guide you to the wiring and connectors associated wi th that fault. Once PD Mode is activated, flex the wiring harness and connectors to attempt to recreate the fault.