What kind of ignition coil does a GMC 1500 have?
This typical circuit diagram of the ignition coil, ignition control module, and pickup coil applies to: 1992, 1993, 1994, 1995 Chevrolet/GMC 1500, 2500, and 3500 Pick Up and Suburban equipped with a 4.3L V6, or a 5.0L v8, or a 5.8L V8 engine.
What happens when the EGR valve gets stuck on a GM 4.3L?
This tutorial addresses a very common problem I’ve seen on the 1987-1995 GM 4.3L, 5.0L, and 5.7L engines with throttle body fuel injection system: a stuck open EGR valve. And when the EGR valve gets stuck open, it’ll cause a rough idle condition that may hard to diagnose.
How does the fuel injection computer regulate the EGR valve?
The fuel injection computer is the one that regulates the opening and closing of the EGR valve thru’ the application and release of vacuum (through a vacuum solenoid). One side of the EGR vacuum solenoid (the one that has only one vacuum inlet port) connects to the vacuum port labeled with the letter J on the throttle body.
What kind of ignition system does a 1993 Chevy pick up have?
1992, 1993, 1994, 1995 Chevrolet/GMC 1500, 2500, and 3500 Pick Up and Suburban equipped with a 4.3L V6, or a 5.0L v8, or a 5.8L V8 engine. 1992, 1993, 1994, 1995 Chevrolet Astro (GMC Safari). NOTE: Testing the ignition system is a breeze.
This typical circuit diagram of the ignition coil, ignition control module, and pickup coil applies to: 1992, 1993, 1994, 1995 Chevrolet/GMC 1500, 2500, and 3500 Pick Up and Suburban equipped with a 4.3L V6, or a 5.0L v8, or a 5.8L V8 engine.
1992, 1993, 1994, 1995 Chevrolet/GMC 1500, 2500, and 3500 Pick Up and Suburban equipped with a 4.3L V6, or a 5.0L v8, or a 5.8L V8 engine. 1992, 1993, 1994, 1995 Chevrolet Astro (GMC Safari). NOTE: Testing the ignition system is a breeze.
What kind of ignition system does a GMC Suburban have?
The typical ignition system circuit diagram for the 1996-1999 4.3L, 5.0L, and 5.7L 1500, 2500, 3500 Pick Up and Suburban can be found here: Ignition System Circuit Diagram (1996-1999 Chevy/GMC Pick Up And SUV). Testing a no-start problem or a misfire due to an ignition system problem is not hard.
What to do if your ECM is not connected to ignition?
Make sure that the red battery wire is connected to a battery source (It is highly recommended that this wire is connected directly to the battery) and the pink wire is connected to an ignition 1 source. If your ignition wire is not connected to an ignition 1 source your ECM will not be powered while cranking the engine. 3.
What was the ignition module on a 1993 GMC k1500?
1993 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a no-start problem caused by the ignition module, or the ignition coil, or the distributor pickup coil. Wiring diagram. Component pin outs.
The typical ignition system circuit diagram for the 1992-1995 4.3L, 5.0L, and 5.7L 1500, 2500, 3500 Pick Up and Suburban can be found here: Ignition System Circuit Diagram (1992-1995 Chevy/GMC Pick Up And SUV).
How does the GM distributor mounted ignition module work?
OK, once the fuel injection computer receives the Distributor Reference Hi Signal, it starts activating the fuel injectors and above 400 RPM, starts to send a 5 Volt Bypass Signal to the ignition control module. It’s with the Bypass Signal that the computer starts to retard and advance ignition timing with the IC Signal.
1993 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a no-start problem caused by the ignition module, or the ignition coil, or the distributor pickup coil. Wiring diagram. Component pin outs.
The typical ignition system circuit diagram for the 1992-1995 4.3L, 5.0L, and 5.7L 1500, 2500, 3500 Pick Up and Suburban can be found here: Ignition System Circuit Diagram (1992-1995 Chevy/GMC Pick Up And SUV).
Can you test the GM distributor mounted ignition module?
The GM distributor mounted ignition control module (ICM), can be tested on the car or truck easily. Not only that, you don’t need any expensive tools to do it.
Where is the transmission on a Jaguar XJ6?
Transmissions are a four-speed automatic equipped with a lock-up torque converter. The transmission is mounted to the back of the engine, and power is transmitted to the fully independent rear axle through a two-piece propshaft.
What kind of suspension does a Jaguar XJ6 have?
The rear suspension is an independent type suspension which also have coil spring/shock absorber assemblies and a lower control arm. The rear driveshaft acts as the upper control arm. Power-assisted Anti-lock Brake Systems (ABS) with four-wheel disc brakes are standard equipment on all Jaguar XJ6 models covered in this manual.
Can you replace the wiring on a Jaguar XJ6?
Incidentally, JagBits has a very nice article written about replacing XJ12 wiring that is also relative to other cars. Pictures too! As it turned out, once the pitiful cloth insulation was removed, many wires leading to the coil where cracked, with some hanging on by a few wire strands underneath.
Is the Jaguar XJ6 Series III a no start car?
I am not a Jaguar mechanic. I own two XJ6’s a black ’81, which I drive everyday, and a black ’83 that I intend to restore. So not being a comprehensive Jaguar mechanic, I was baffled as to the cause of a deteriorating no-start problem.
Can a Jaguar XJ12 be replaced under the bonnet?
The Brits (still trying to get back at us for the Revolution), are very poor with their wire insulation and even worse at their artistic endeavor to provide a clean under-bonnet wiringat least in this vintage Jaguar. Incidentally, JagBits has a very nice article written about replacing XJ12 wiring that is also relative to other cars.
What kind of transmission does a Jaguar XJ6 have?
Jaguar XJ6 Service and Repair Manual 3261 Jaguar XJ6 Models covered Jaguar XJ6 models with 3.2 litre (3239 cc), 3.6 litre (3590 cc) & 4.0 litre (3980 cc) six-cylinder in-line dohc petrol engines and automatic transmission